Luc Vivien Assiene Mouodo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Luc Vivien Assiene Mouodo has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Petros J. Axaopoulos
Department of Mechanical Engineering, University of West Attica, Campus II, Thivon 250, 12 241 Aegaleo, Greece
5 shared publications Jean Gaston Tamba
4 shared publicationsNna Nna Theodore Patrice
3 shared publicationsPetros Axaopoulos
3 shared publications- Abdel-Hamid Mahamat Ali
Department of Engineering Electrical, National Higher Institute University, Ndjamena P.O. Box 1872, Chad
2 shared publications - Felix Paune
Department of Computer Engineering, ENSET Douala, University of Douala, Douala P.O. Box 1872, Cameroon
2 shared publications
Latest Publications
- Open Access
- 1 September 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (17) , 8698
Hybrid Electro-Thermal and FNN Framework for Joint SoC, SoH Estimation and Lifetime Prediction of Lithium-Ion Batteries in Electric Vehicles
Improving the performance and lifespan of lithium-ion batteries is a key challenge for the development of electric vehicles. However, accurately estimating the state of charge (SoC), state of health (SoH), and life cycle remains complex due to the electrical, thermal, and aging phenomena associated with these energy storage systems. Against this backdrop, this study proposes a hybrid approach combining an electro-thermal model with a feedforward neural network (FNN) to improve the estimation of key lithium-ion battery performance indicators within a temperature range of 0 °C to 40 °C. The developed methodology was implemented in MATLAB/Simulink and applied to the analysis of the vehicle’s power profile, as well as the evolution of SoC, SoH, and battery life cycle. The results demonstrate an accuracy of 95.3% for state of charge (SoC) estimation, with a mean absolute error of 4.7%. For state of health (SoH) estimation, the accuracy is 95.8% accompanied by a mean absolute error of 4.2%. Lastly, for life cycle prediction, the accuracy is 92.5% with a mean absolute error of 7.5%. The performance results demonstrate the robustness of the proposed approach and its ability to replicate battery dynamic behavior under climatic conditions representative of the African context. This contribution opens up promising avenues for optimizing battery management systems and advancing the sustainable development of electric mobility.
- 1 September 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (17) , 8698
Open AccessHybrid Electro-Thermal and FNN Framework for Joint SoC, SoH Estimation and Lifetime Prediction of Lithium-Ion Batteries in Electric Vehicles
Improving the performance and lifespan of lithium-ion batteries is a key challenge for the development of electric vehicles. However, accurately estimating the state of charge (SoC), state of health (SoH), and life cycle remains complex due to the electrical, thermal, and aging phenomena associated with these energy storage systems. Against this backdrop, this study proposes a hybrid approach combining an electro-thermal model with a feedforward neural network (FNN) to improve the estimation of key lithium-ion battery performance indicators within a temperature range of 0 °C to 40 °C. The developed methodology was implemented in MATLAB/Simulink and applied to the analysis of the vehicle’s power profile, as well as the evolution of SoC, SoH, and battery life cycle. The results demonstrate an accuracy of 95.3% for state of charge (SoC) estimation, with a mean absolute error of 4.7%. For state of health (SoH) estimation, the accuracy is 95.8% accompanied by a mean absolute error of 4.2%. Lastly, for life cycle prediction, the accuracy is 92.5% with a mean absolute error of 7.5%. The performance results demonstrate the robustness of the proposed approach and its ability to replicate battery dynamic behavior under climatic conditions representative of the African context. This contribution opens up promising avenues for optimizing battery management systems and advancing the sustainable development of electric mobility.
- Open Access
- 12 August 2026
- Published by MDPI AG in Preprints.org
Hybrid Electro-Thermal and FNN Framework for Joint SoC, SoH Estimation and Lifetime Prediction of Lithium-Ion Batteries in Electric Vehicles
Improving the performance and lifespan of lithium-ion batteries is a key challenge for the development of electric vehicles. However, accurately estimating the state of charge (SoC), state of health (SoH), and lifecycle remains complex due to the electrical, thermal, and aging phenomena associated with these energy storage systems. Against this backdrop, this study proposes a hybrid approach combining an electro-thermal model with a feedforward neural network (FNN) to improve the estimation of key lithium-ion battery performance indicators within a temperature range of 0 °C et 40 °C. The developed methodology was implemented in MATLAB/Simulink and applied to the analysis of the vehicle's power profile, as well as the evolution of SoC, SoH, and battery lifecycle. The results demonstrate an accuracy of 95.3% for State of Charge (SoC) estimation, with a mean absolute error of 4.7%. For State of Health (SoH) estimation, the accuracy is 95.8% accompanied by a mean absolute error of 4.2%. Lastly, for lifecycle prediction, the accuracy is 92.5% with a mean absolute error of 7.5%. The performance results demonstrate the robustness of the proposed approach and its ability to replicate battery dynamic behavior under climatic conditions representative of the African context. This contribution opens up promising avenues for optimizing battery management systems and advancing the sustainable development of electric mobility.
- 12 August 2026
- Published by MDPI AG in Preprints.org
Open AccessHybrid Electro-Thermal and FNN Framework for Joint SoC, SoH Estimation and Lifetime Prediction of Lithium-Ion Batteries in Electric Vehicles
Improving the performance and lifespan of lithium-ion batteries is a key challenge for the development of electric vehicles. However, accurately estimating the state of charge (SoC), state of health (SoH), and lifecycle remains complex due to the electrical, thermal, and aging phenomena associated with these energy storage systems. Against this backdrop, this study proposes a hybrid approach combining an electro-thermal model with a feedforward neural network (FNN) to improve the estimation of key lithium-ion battery performance indicators within a temperature range of 0 °C et 40 °C. The developed methodology was implemented in MATLAB/Simulink and applied to the analysis of the vehicle's power profile, as well as the evolution of SoC, SoH, and battery lifecycle. The results demonstrate an accuracy of 95.3% for State of Charge (SoC) estimation, with a mean absolute error of 4.7%. For State of Health (SoH) estimation, the accuracy is 95.8% accompanied by a mean absolute error of 4.2%. Lastly, for lifecycle prediction, the accuracy is 92.5% with a mean absolute error of 7.5%. The performance results demonstrate the robustness of the proposed approach and its ability to replicate battery dynamic behavior under climatic conditions representative of the African context. This contribution opens up promising avenues for optimizing battery management systems and advancing the sustainable development of electric mobility.
- Open Access
- 6 July 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (13) , 6756
Experimental Approach to Intelligent Estimation of the State-of-Charge (SoC) of Batteries: Case of Electric Vehicles
The development of the electric vehicle sector increasingly requires optimal intelligent and embedded energy management. Electric vehicles are now positioning themselves as a strategic alternative to traditional fuel vehicles. This article therefore highlights the design of an embedded system capable of evaluating and transmitting in real time the state-of-charge (SoC) of an electric vehicle battery to a cloud platform, while optimizing energy consumption and data reliability. The methodological approach proposes an experimental study involving the development of two deep learning models, LSTM (Long Short-Term Memory) and GRU (Gated Recurrent Unit), in the MATLAB 2024.b environment, associated with the design of an embedded prototype for data collection and transmission via Arduino IoT Cloud. Then, a comparative analysis of the models’ performances is also carried out. The results obtained show that the GRU model offers the best performance, with an accuracy of 83.6%, an MSE of 0.0715, and an RMSE of 0.2589, thus validating the relevance of the proposed approach for the intelligent estimation of the state-of-charge in a real application context.
- 6 July 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (13) , 6756
Open AccessExperimental Approach to Intelligent Estimation of the State-of-Charge (SoC) of Batteries: Case of Electric Vehicles
The development of the electric vehicle sector increasingly requires optimal intelligent and embedded energy management. Electric vehicles are now positioning themselves as a strategic alternative to traditional fuel vehicles. This article therefore highlights the design of an embedded system capable of evaluating and transmitting in real time the state-of-charge (SoC) of an electric vehicle battery to a cloud platform, while optimizing energy consumption and data reliability. The methodological approach proposes an experimental study involving the development of two deep learning models, LSTM (Long Short-Term Memory) and GRU (Gated Recurrent Unit), in the MATLAB 2024.b environment, associated with the design of an embedded prototype for data collection and transmission via Arduino IoT Cloud. Then, a comparative analysis of the models’ performances is also carried out. The results obtained show that the GRU model offers the best performance, with an accuracy of 83.6%, an MSE of 0.0715, and an RMSE of 0.2589, thus validating the relevance of the proposed approach for the intelligent estimation of the state-of-charge in a real application context.
- Open Access
New Experimental Approach for Optimizing Electrical Power Quality Through Harmonic Pollution Control: The Case of a Hybrid Filter on Variable Electrical Networks
The quality of electrical power on distribution networks depends heavily on the performance of the harmonic filtering method implemented according to the operating conditions of the system under study. This article proposes a new experimental approach that allows us to determine the dynamic behavior of the harmonic signature of the nonlinear load connected to the electrical network. The ultimate goal is to propose a new law for extracting the reference currents required during the overall online harmonic filtering process using a hybrid filter. This offers advantages in robustness and accuracy during variations in the electrical network compared to the classical methods used in the current literature. The methodological approach consists of selecting several nonlinear loads according to specific profiles and technical characteristics, then experimentally analyzing their harmonic signatures over time to obtain new models for extracting reference currents that will ultimately be faster to implement. In a decentralized global harmonic filtering strategy using a TLC adaptive hybrid filter compliant with the IEEE-519-2022 standard, the results obtained offer THD (total harmonic distortion) values of 1.88%, 3.29%, and 2.78% in three-phase currents, with a reduced DC voltage consumption of 105 V for the inverter. This contrasts with similar models in the current literature, which require input DC voltages exceeding 850 V for identical performance. This work therefore represents a major contribution to new models for extracting experimentally obtained reference currents, enabling the optimization of power quality on electrical networks through the use of a hybrid filter.
Open AccessNew Experimental Approach for Optimizing Electrical Power Quality Through Harmonic Pollution Control: The Case of a Hybrid Filter on Variable Electrical Networks
The quality of electrical power on distribution networks depends heavily on the performance of the harmonic filtering method implemented according to the operating conditions of the system under study. This article proposes a new experimental approach that allows us to determine the dynamic behavior of the harmonic signature of the nonlinear load connected to the electrical network. The ultimate goal is to propose a new law for extracting the reference currents required during the overall online harmonic filtering process using a hybrid filter. This offers advantages in robustness and accuracy during variations in the electrical network compared to the classical methods used in the current literature. The methodological approach consists of selecting several nonlinear loads according to specific profiles and technical characteristics, then experimentally analyzing their harmonic signatures over time to obtain new models for extracting reference currents that will ultimately be faster to implement. In a decentralized global harmonic filtering strategy using a TLC adaptive hybrid filter compliant with the IEEE-519-2022 standard, the results obtained offer THD (total harmonic distortion) values of 1.88%, 3.29%, and 2.78% in three-phase currents, with a reduced DC voltage consumption of 105 V for the inverter. This contrasts with similar models in the current literature, which require input DC voltages exceeding 850 V for identical performance. This work therefore represents a major contribution to new models for extracting experimentally obtained reference currents, enabling the optimization of power quality on electrical networks through the use of a hybrid filter.
- Open Access
- 20 March 2026
- Published by Elsevier in Results in Engineering
- Vol. 30
Design of an optimal vector control of an induction motor for electric vehicles
- 20 March 2026
- Published by Elsevier in Results in Engineering
- Vol. 30
Open AccessDesign of an optimal vector control of an induction motor for electric vehicles
- Open Access
- 31 July 2025
- Published by Seventh Sense Research Group Journals in International Journal of Electronics and Communication Engineering
- Vol. 12 (7)
Impact of an Innovative Approach in the Management of the Electricity Network in Cameroon
This paper highlights an innovative adaptive approach to optimize network topology and Distributed Generation (DG) placement with the objective of reducing power losses and optimizing voltage stability. The methodological approach proposes a metaheuristic algorithm inspired by the CUCKOO model for which the process of selecting the best solutions for successive iterations immediately integrates the convergence criteria (number of iterations, tolerance); this algorithm is tested respectively on the networks: IEEE-33, IEEE-69, and on the Northern Interconnected Networks (RIN) Cameroon; and this with 4 operating scenarios for each network with an estimation of convergence performance and a comparison with the current literature; the decentralized PV production used is permanent as a working hypothesis for the implementation. The results obtained for the case of the RIN Cameroon offer a reduction in power losses of 23.9647%, for a minimum voltage of 0.97762 PU. Thus, demonstrating the effectiveness and performance of the proposed method in optimizing the management of the reconfiguration of electrical networks. A comparison of its results with those of the literature allows us to recommend this work in particular for the development program of the Energy sector horizon 2030 (PDSE 20230) for Cameroon. And in general, for the reconfiguration of electrical networks.
- 31 July 2025
- Published by Seventh Sense Research Group Journals in International Journal of Electronics and Communication Engineering
- Vol. 12 (7)
Open AccessImpact of an Innovative Approach in the Management of the Electricity Network in Cameroon
This paper highlights an innovative adaptive approach to optimize network topology and Distributed Generation (DG) placement with the objective of reducing power losses and optimizing voltage stability. The methodological approach proposes a metaheuristic algorithm inspired by the CUCKOO model for which the process of selecting the best solutions for successive iterations immediately integrates the convergence criteria (number of iterations, tolerance); this algorithm is tested respectively on the networks: IEEE-33, IEEE-69, and on the Northern Interconnected Networks (RIN) Cameroon; and this with 4 operating scenarios for each network with an estimation of convergence performance and a comparison with the current literature; the decentralized PV production used is permanent as a working hypothesis for the implementation. The results obtained for the case of the RIN Cameroon offer a reduction in power losses of 23.9647%, for a minimum voltage of 0.97762 PU. Thus, demonstrating the effectiveness and performance of the proposed method in optimizing the management of the reconfiguration of electrical networks. A comparison of its results with those of the literature allows us to recommend this work in particular for the development program of the Energy sector horizon 2030 (PDSE 20230) for Cameroon. And in general, for the reconfiguration of electrical networks.
- 15 July 2025
- Published by Elsevier in Journal of Energy Storage
- Vol. 132
Contribution to optimizing the performance of chargers for electric vehicle batteries: Case of AC-DC converters
- 15 July 2025
- Published by Elsevier in Journal of Energy Storage
- Vol. 132
Contribution to optimizing the performance of chargers for electric vehicle batteries: Case of AC-DC converters
- Open Access
Optimization and Estimation of the State of Charge of Lithium-Ion Batteries for Electric Vehicles
Lithium batteries have become one of the best choices for current consumer electric vehicle batteries due to their good stability and high energy density. To ensure the safety and reliability of electric vehicles (EVs), the battery management system (BMS) must provide accurate and real-time information on the usage status of the onboard battery. This article highlights the precise estimation of the state of charge (SOC) applied to four models of lithium-ion batteries (Turnigy, LG, SAMSUNG, and PANASONIC) for electric vehicles in order to ensure optimal use of the battery and extend its lifespan, which is frequently influenced by certain parameters such as temperature, current, number of charge and discharge cycles, and so on. Because of the work’s novelty, the methodological approach combines the extended Kalman filter algorithm (EKF) with the noise matrix, which is updated in this case through an iterative process. This leads to the migration to a new adaptive extended Kalman filter algorithm (AEKF) in the MATLAB Simulink 2022.b environment, which is novel or original in the sense that it has a first-order association. The four models of batteries from various manufacturers were directly subjected to the Venin estimator, which allowed for direct comparison of the models under a variety of temperature scenarios while keeping an eye on performance metrics. The results obtained were mapped charging status (SOC) versus open circuit voltage (OCV), and the high-performance primitives collection (HPPC) tests were carried out at 40 °C, 25 °C, 10 °C, 0 °C and −10 °C. At these temperatures, their corresponding values for the root mean square error (RMSE) of (SOC) for the Turnigy graphene battery model were found to be: 1.944, 9.6237, 1.253, 1.6963, 16.9715, and for (OCV): 1.3154, 4.895, 4.149, 4.1808, and 17.2167, respectively. The tests cover the SOC range, from 100% to 5% with four different charge and discharge currents at rates of 1, 2, 5 and 10 A. After characterization, the battery was subjected to urban dynamometer driving program (UDDS), Energy Saving Test (HWFET) driving cycles, LA92 (Dynamometric Test), US06 (aggressive driving), as well as combinations of these cycles. Driving cycles were sampled every 0.1 s, and other tests were sampled at a slower or variable frequency, thus verifying the reliability and robustness of the estimator to 97%.
Open AccessOptimization and Estimation of the State of Charge of Lithium-Ion Batteries for Electric Vehicles
Lithium batteries have become one of the best choices for current consumer electric vehicle batteries due to their good stability and high energy density. To ensure the safety and reliability of electric vehicles (EVs), the battery management system (BMS) must provide accurate and real-time information on the usage status of the onboard battery. This article highlights the precise estimation of the state of charge (SOC) applied to four models of lithium-ion batteries (Turnigy, LG, SAMSUNG, and PANASONIC) for electric vehicles in order to ensure optimal use of the battery and extend its lifespan, which is frequently influenced by certain parameters such as temperature, current, number of charge and discharge cycles, and so on. Because of the work’s novelty, the methodological approach combines the extended Kalman filter algorithm (EKF) with the noise matrix, which is updated in this case through an iterative process. This leads to the migration to a new adaptive extended Kalman filter algorithm (AEKF) in the MATLAB Simulink 2022.b environment, which is novel or original in the sense that it has a first-order association. The four models of batteries from various manufacturers were directly subjected to the Venin estimator, which allowed for direct comparison of the models under a variety of temperature scenarios while keeping an eye on performance metrics. The results obtained were mapped charging status (SOC) versus open circuit voltage (OCV), and the high-performance primitives collection (HPPC) tests were carried out at 40 °C, 25 °C, 10 °C, 0 °C and −10 °C. At these temperatures, their corresponding values for the root mean square error (RMSE) of (SOC) for the Turnigy graphene battery model were found to be: 1.944, 9.6237, 1.253, 1.6963, 16.9715, and for (OCV): 1.3154, 4.895, 4.149, 4.1808, and 17.2167, respectively. The tests cover the SOC range, from 100% to 5% with four different charge and discharge currents at rates of 1, 2, 5 and 10 A. After characterization, the battery was subjected to urban dynamometer driving program (UDDS), Energy Saving Test (HWFET) driving cycles, LA92 (Dynamometric Test), US06 (aggressive driving), as well as combinations of these cycles. Driving cycles were sampled every 0.1 s, and other tests were sampled at a slower or variable frequency, thus verifying the reliability and robustness of the estimator to 97%.
- Open Access
- 31 May 2025
- Published by Seventh Sense Research Group Journals in International Journal of Electronics and Communication Engineering
- Vol. 12 (5) , 94-107
Control and Analysis of a Power System From a Dual IPC_240 System Controlled by FPGA in High Contingencies Situations
This work presents automatic management methods for handling single-phase or two-phase faults on an electrical power transmission line, enabling the redirection of power flow from the defective phase to the normal phases. When one or more phases are disconnected, the automated system provides a portion of the rated power on the receiving side while maintaining the three-phase balance of the load supply. In the event of a fault, alerts are sent in real-time to operators via SMS on their phones or by email, accompanied by an audible alarm and the activation of the relevant indicator lights. This type of work is particularly crucial for both developing countries and developed nations facing frequent short circuits in power transmission networks, as it improves system flexibility and reliability. The Field Programmable Gate Array (FPGA), combined with a communication module and programmed in VHDL, generates a series of logic gates. It was integrated into the QUARTUS II environment for real-time monitoring of its operation. The outcomes of the simulations confirm the possibility of implementation and effectiveness of the two 240 interphase power controller technologies in managing energy flow, both in standard situations and in times of emergency. Overall, the results demonstrate that using two interphase power regulators, one on the source side and the other on the load side, ensures 98% stability in the transmission of electrical energy.
- 31 May 2025
- Published by Seventh Sense Research Group Journals in International Journal of Electronics and Communication Engineering
- Vol. 12 (5) , 94-107
Open AccessControl and Analysis of a Power System From a Dual IPC_240 System Controlled by FPGA in High Contingencies Situations
This work presents automatic management methods for handling single-phase or two-phase faults on an electrical power transmission line, enabling the redirection of power flow from the defective phase to the normal phases. When one or more phases are disconnected, the automated system provides a portion of the rated power on the receiving side while maintaining the three-phase balance of the load supply. In the event of a fault, alerts are sent in real-time to operators via SMS on their phones or by email, accompanied by an audible alarm and the activation of the relevant indicator lights. This type of work is particularly crucial for both developing countries and developed nations facing frequent short circuits in power transmission networks, as it improves system flexibility and reliability. The Field Programmable Gate Array (FPGA), combined with a communication module and programmed in VHDL, generates a series of logic gates. It was integrated into the QUARTUS II environment for real-time monitoring of its operation. The outcomes of the simulations confirm the possibility of implementation and effectiveness of the two 240 interphase power controller technologies in managing energy flow, both in standard situations and in times of emergency. Overall, the results demonstrate that using two interphase power regulators, one on the source side and the other on the load side, ensures 98% stability in the transmission of electrical energy.
- Open Access
- 1 January 2025
- Published by Institution of Engineering and Technology (IET) in IET Renewable Power Generation
- Vol. 19 (1)
Control of Photovoltaic‐Based Shunt Active Power Filter System Based on Optimal Operating Point Tracking of PV System for Harmonic Mitigation, Load Supply and Grid Current Injection
This paper explores an innovative control strategy for photovoltaic‐based shunt active power filters (PV‐SAPF), aiming to enhance power quality, support load supply, and inject low‐harmonic current into the grid. Unlike existing approaches that rely solely on MPPT‐controlled inverters for optimal PV performance, this method integrates an optimal operating point tracking (OOPT) algorithm with a harmonic identification method (HIM), enabling comprehensive system functionality. The control scheme employs a HIM modules to generate reference currents, facilitating harmonic mitigation, reactive power compensation, and load support under varying energy production conditions. MATLAB/Simulink simulations demonstrate the effectiveness of this approach in maintaining grid stability during both energy surplus and deficit scenarios. When energy exceeds load demand, the PV‐SAPF supplies the load and injects less than 1% THD into the grid; during underproduction, it partially supplies the load and mitigates harmonics. The results adhere to IEEE Std 519‐2022 standards, showcasing the system's ability to improve power quality and grid harmony. Notably, this strategy differs from previous methods by removing the need for MPPT‐controlled converters and allowing compatibility with any harmonic identification technique, thus offering a versatile and efficient solution for integrating PV systems into the power grid.
- 1 January 2025
- Published by Institution of Engineering and Technology (IET) in IET Renewable Power Generation
- Vol. 19 (1)
Open AccessControl of Photovoltaic‐Based Shunt Active Power Filter System Based on Optimal Operating Point Tracking of PV System for Harmonic Mitigation, Load Supply and Grid Current Injection
This paper explores an innovative control strategy for photovoltaic‐based shunt active power filters (PV‐SAPF), aiming to enhance power quality, support load supply, and inject low‐harmonic current into the grid. Unlike existing approaches that rely solely on MPPT‐controlled inverters for optimal PV performance, this method integrates an optimal operating point tracking (OOPT) algorithm with a harmonic identification method (HIM), enabling comprehensive system functionality. The control scheme employs a HIM modules to generate reference currents, facilitating harmonic mitigation, reactive power compensation, and load support under varying energy production conditions. MATLAB/Simulink simulations demonstrate the effectiveness of this approach in maintaining grid stability during both energy surplus and deficit scenarios. When energy exceeds load demand, the PV‐SAPF supplies the load and injects less than 1% THD into the grid; during underproduction, it partially supplies the load and mitigates harmonics. The results adhere to IEEE Std 519‐2022 standards, showcasing the system's ability to improve power quality and grid harmony. Notably, this strategy differs from previous methods by removing the need for MPPT‐controlled converters and allowing compatibility with any harmonic identification technique, thus offering a versatile and efficient solution for integrating PV systems into the power grid.