Peng Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Peng Wang has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Bin Zou
Center for Advanced Jet Engineering Technologies (CaJET), School of Mechanical Engineering, Shandong University, Jinan 250061, China
2 shared publications - Shouling Ding
Centre for Advanced Jet Engineering Technologies (CaJET), School of Mechanical Engineering, Shandong University, Jinan 250061, China
1 shared publication - Yuexi Zhuang
Centre for Advanced Jet Engineering Technologies (CaJET), School of Mechanical Engineering, Shandong University, Jinan 250061, China
1 shared publication
Latest Publications
- Open Access
Shear and Tensile Behaviors of Fiber-Reinforced Resin Matrix Composites Printed by the FDM Technology
Resin/fiber composites were prepared by the FDM printing technology. The effects of arrangements, types (carbon, glass, and Kevlar), and volume fraction of fibers on the shear and tensile properties of resin 3D-printed composites are investigated in this paper. The experimental results show that the addition of continuous fibers increases the shear strength and tensile strength of FDM-3D-printed composites, but the strength will not keep increasing with an increase in the fiber content. As the fiber content increases, the print quality decreases, and the porosity between the fibers increases. The enhancement degree of the shear stress of specimens by different fiber types can be classified as follows: glass fiber > carbon fiber > Kevlar fiber. Notch sensitivity is reduced when the 90° arrangement of fibers is added, while the addition of 0° arranged fibers will improve the notch sensitivity of the sample. The research results of this paper have an important guiding significance for selecting fiber types and arrangement mode of notched components in engineering applications.
Open AccessShear and Tensile Behaviors of Fiber-Reinforced Resin Matrix Composites Printed by the FDM Technology
Resin/fiber composites were prepared by the FDM printing technology. The effects of arrangements, types (carbon, glass, and Kevlar), and volume fraction of fibers on the shear and tensile properties of resin 3D-printed composites are investigated in this paper. The experimental results show that the addition of continuous fibers increases the shear strength and tensile strength of FDM-3D-printed composites, but the strength will not keep increasing with an increase in the fiber content. As the fiber content increases, the print quality decreases, and the porosity between the fibers increases. The enhancement degree of the shear stress of specimens by different fiber types can be classified as follows: glass fiber > carbon fiber > Kevlar fiber. Notch sensitivity is reduced when the 90° arrangement of fibers is added, while the addition of 0° arranged fibers will improve the notch sensitivity of the sample. The research results of this paper have an important guiding significance for selecting fiber types and arrangement mode of notched components in engineering applications.
- Open Access
Improvement of Heat Treatment Process on Mechanical Properties of FDM 3D-Printed Short- and Continuous-Fiber-Reinforced PEEK Composites
Due to the addition of short/continuous fibers with better mechanical properties, FDM 3D-printed short- and continuous-fiber-reinforced PEEK composites possess better performance than printed PEEK. However, the interlayer bonding performance becomes poor due to the layer stacking and weak fiber–resin interface adhesion. In this study, a heat treatment process was proposed to improve the interlaminar bonding properties of 3D-printed short- and continuous-fiber-reinforced PEEK composites. The effects of heat treatment temperature and time on the interlaminar shear strength, porosity and dimensional change of printed samples were studied by a single-factor experiment. Moreover, the thermal properties and fracture morphology of FDM 3D-printed fiber-reinforced PEEK composites before and after heat treatment were investigated to explore the toughening and strengthening mechanism. The experimental results showed that the mechanical properties of FDM 3D-printed fiber-reinforced PEEK composites improved by heat treatment process can be attributed to the improvement of crystallinity and interfacial bonding. The heat treatment process can also improve the infiltration and diffusion among adjacent filaments and layers, and further reduce the defects. The optimized heat treatment temperature and time were 250 °C and 6 h, respectively. The maximum ILSS of FDM 3D-printed short- and continuous-fiber-reinforced PEEK composites increased by 16 and 85% compared with untreated samples, respectively.
Open AccessImprovement of Heat Treatment Process on Mechanical Properties of FDM 3D-Printed Short- and Continuous-Fiber-Reinforced PEEK Composites
Due to the addition of short/continuous fibers with better mechanical properties, FDM 3D-printed short- and continuous-fiber-reinforced PEEK composites possess better performance than printed PEEK. However, the interlayer bonding performance becomes poor due to the layer stacking and weak fiber–resin interface adhesion. In this study, a heat treatment process was proposed to improve the interlaminar bonding properties of 3D-printed short- and continuous-fiber-reinforced PEEK composites. The effects of heat treatment temperature and time on the interlaminar shear strength, porosity and dimensional change of printed samples were studied by a single-factor experiment. Moreover, the thermal properties and fracture morphology of FDM 3D-printed fiber-reinforced PEEK composites before and after heat treatment were investigated to explore the toughening and strengthening mechanism. The experimental results showed that the mechanical properties of FDM 3D-printed fiber-reinforced PEEK composites improved by heat treatment process can be attributed to the improvement of crystallinity and interfacial bonding. The heat treatment process can also improve the infiltration and diffusion among adjacent filaments and layers, and further reduce the defects. The optimized heat treatment temperature and time were 250 °C and 6 h, respectively. The maximum ILSS of FDM 3D-printed short- and continuous-fiber-reinforced PEEK composites increased by 16 and 85% compared with untreated samples, respectively.