KHKarl D. Hirschman

Karl D. Hirschman

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Karl D. Hirschman has a total of 82 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Thermally Dependent Metastability of Indium-Tungsten-Oxide Thin-Film Transistors

    by Eli Powell, Meghana Nagesha, Robert G. Manley, Bin Zhu, Karl D. Hirschman

    Indium tungsten oxide (IWO) has been investigated as an oxide semiconductor candidate for next-generation thin-film transistors (TFTs). Bottom-gate TFTs were fabricated with a 30-nm IWO channel material sputter-deposited with oxygen partial pressure (PO2) ranging from 2.5% to 10% of the total ambient pressure. Annealing was conducted at temperatures ranging from 100ºC to 275ºC. Device transfer characteristic measurements revealed a pronounced interaction between the sputter PO2 setting and passivation annealing conditions. Devices annealed at 100ºC in air ambient demonstrated characteristics with a strong dependence on PO2, attributed to differences in oxygen vacancy defects and semiconductor electronic properties. Devices annealed at 200ºC in air ambient demonstrated characteristics like those of unannealed devices, with operation far in depletion mode. Donor state passivation is possible following additional annealing at 275ºC in air, with reduced sensitivity to the initial sputter PO2 setting. A hypothesis on the mechanism of metastability is proposed.

  • Temperature Dependence of Intrinsic Channel Mobility in Indium-Gallium-Zinc-Oxide TFTs

    by Muhammad S. Kabir, Robert G. Manley, Karl D. Hirschman

    This work reports on the development of a new TCAD material and device model for Indium-Gallium-Zinc-Oxide TFTs that accounts for operation from 150 K to room temperature, over applied gate and drain bias conditions up to 10 V. Specified defect state distributions include oxygen vacancy donors, conduction band-tail acceptor states, and acceptor-like interface traps. The presented model allows the TCAD simulation to account for the behavior of defect states according to defined energy distributions, thus properly regulating the amount of free channel charge. An intrinsic channel mobility defined as only a function of temperature was found to accurately represent extended state transport. The intrinsic channel mobility was 19 cm 2 /V•s at room temperature, with a reduction to 9 cm 2 /V•s at T = 150 K. The functional dependence reflects a thermally-activated diffusive mobility with a distinct activation energy E a = 40 meV, that is shown to be independent of the Fermi level.


  • Flash Lamp Annealed LTPS TFTs with ITO Bottom-Gate Structures

    by Glenn Packard, Adam Rosenfeld, Robert G. Manley, Karl D. Hirschman

    Low-Temperature Polycrystalline Silicon (LTPS) thin-film transistors (TFTs) are usually built as a top-gate structure. This is due to the serious challenge presented by locally crystallizing a thin layer of amorphous silicon that has regions of overlap with an absorptive and thermally conductive gate electrode and areas of thermally insulating glass. Early attempts to create LTPS devices quickly switched from the industry standard of bottom-gate to the more attainable top-gate, in which a gate structure is deposited subsequent to crystallization [1]. Despite this difficulty, bottom-gate devices offer potential benefits in breakdown voltage and dielectric-semiconductor interface quality, as well as being a requirement for double-gate devices and enabling higher fill-factor pixel designs in TFT display backplanes. Bottom-gate TFTs have been realized with crystallization via excimer laser annealing (ELA) with a demonstrated improvement over top-gate devices [2]. This is of particular interest for the development of LTPS devices that employ an alternative crystallization technique, such as metal-induced lateral crystallization [3, 4] and continuous-wave laser annealing [5, 6], motivated by potential advantages in large-panel manufacturing. FLA (Flash lamp annealing) has been explored as an alternative to ELA LTPS [7], and has the potential to streamline and decrease the cost of fabrication while providing applicable electrical performance. In this method, amorphous silicon is exposed to a single pulse of light emitted from a xenon flash lamp, causing melting and recrystallization in an area of cm2 rather than nm2 in less than a millisecond. FLA has shown value in crystallizing silicon and activating dopants in both PFET and NFET TFTs [8]. Early attempts to produce bottom-gate FLA-LTPS TFTs were ineffective; the high degree of light absorption and reflectivity in metal or polysilicon gates resulted in severe, localized ablation of the overlying channel silicon. Reducing FLA emission intensity prevented this catastrophic channel loss, but also reduced the crystallization of source/drain region silicon to the point where device performance was dominated by series resistance. In this work, bottom-gate LTPS TFTs are realized using FLA by incorporating indium-tin oxide (ITO) as a transparent conductive gate electrode material. The reduction in absorbance and reflectivity, as well as the enhanced thermal and chemical stability, of ITO allows for the simultaneous, comparable crystallization of both channel silicon above the gate and adjacent source/drain silicon regions above SiO2 and glass substrate. A finalized ITO bottom-gate PFET is shown in Figure 1A and an in-progress image after FLA and ion implantation in 1B. A distinction is visible between silicon over the gate and freestanding silicon, with an even sharper distinction between implanted source-drain silicon over the gate and the true, non-implanted channel. It is clear that the presence of an ITO gate locally enhances silicon crystallization with a slight lateral bleed, but this effect does not dominate to the point of damaging the channel. A subsequent 630 °C furnace treatment provides for both dopant activation and recrystallization of amorphized regions. P-channel TFTs fabricated with ITO bottom gates demonstrated excellent device performance, as shown in Figures 1C and 1D. The ION/IOFF ratio is between 6 and 7 orders of magnitude with notably low off-state leakage. The typical device shown exhibits a threshold voltage VT ~ -5.0 V. The channel mobility was extracted using the maximum transconductance method, indicating a hole µch ~ 190 cm2/Vs. Most transfer characteristics experienced significant degradation at higher drain bias conditions for reasons still under investigation. Nevertheless, these preliminary results provide direction for further investigation, which include the study of a double-gate structure for comparisons in device performance and stability. The additional presence of a top gate will improve electrostatic control of the channel charge, mitigating problems caused by interface trap states with an effect similar to enhanced channel passivation. Further passivation efforts using hydrogen/nitrogen plasma treatments will be incorporated in tandem; these are more effective on bottom and double-gate structures due to easier channel access at the processing back-end. In addition, FLA is being explored as a replacement for the long furnace anneal currently used for dopant activation. Figure 1

  • Interpretation of Donor Activation in Boron and Argon Implanted Self-Aligned Bottom-Gate IGZO TFTs

    by Muhammad Salahuddin Kabir, Rahnuma Rifat Chowdhury, Robert G. Manley, Karl D. Hirschman

    The source/drain electrodes in IGZO TFTs (thin-film transistors) can be direct metal overlapping the IGZO region. However, to achieve ohmic behavior with minimal resistance and ensure tolerance to overlay error, several microns of gate overlap is required. IGZO TFTs with self-aligned channel regions have advantages in reduced parasitic capacitance and stage delay, and a reduction in overhead real estate. Several techniques have been used to selectively form conductive IGZO regions including the introduction of hydrogen [1, 2], plasma exposure [3] and ion implantation [4, 5]. This work provides an interpretation of donor activation in self-aligned bottom-gate (SA-BG) IGZO TFTs with ion-implantation of boron (11B+) and argon (40Ar+) species as the source/drain treatment. Preliminary work investigated a top-gate electrode configuration, which served as the implant mask for the self-aligned strategy. These devices exhibited a significant left-shift in the ID-VGS transfer characteristics that was attributed to charge accumulation on the metal gate, subjecting the gate dielectric to a high electric field and the creation of ionized defects [5]. The bottom-gate implementation utilizes the opaque gate electrode as a mask for a through-wafer exposure of positive photoresist, providing a perfectly aligned implant mask that averted this charging mechanism. Both 11B+ and 40Ar+ implanted SA-BG devices exhibited electrical characteristics that were consistent with non-SA devices [6], with minimal impact of added series resistance. However, there were noted differences in the device operation that became pronounced following thermal stress treatments below 200 °C. Hypotheses in the mechanisms involved with donor activation have been developed from both similarities and differences in electrical behavior. Results suggest a defect-induced mechanism is responsible for implant activation with 40Ar+, whereas implant activation with 11B+ is attributed to the formation of an electrically active donor species involving chemical bonding. Examination of characteristics measured before and after applied thermal stress will be used to explain the interpretation, with the additional support of SIMS and XPS analysis. References H. Wu, H. H. Hsieh, C. W. Chien, and C. C. Wu, “Self-aligned top-gate coplanar In–Ga–Zn–O thin-film transistors,” J. Display Technol., vol.5, no. 12, pp. 515–519, Dec. 2009. H. Kang, I. Kang, S. H. Ryu, and J. Jang, “Self-aligned coplanar a-IGZO TFTs and application to high-speed circuits,” IEEE Electron Device Lett., vol. 32, no. 10, pp. 1385–1387, Oct. 2011. Park, I. Song, S. Kim, S. Kim, C. Kim, J. Lee, H. Lee, E. Lee, H. Yin, K. Kim, K. Kwon, and Y. Park, “Self-aligned top-gate amorphous gallium indium zinc oxide thin film transistors,” Appl. Phys. Lett., vol. 93, no. 5, p. 053501, Aug. 2008. Chen, W. Zhou, M. Zhang, M. Wong, and H. S. Kwok, “Self-Aligned Indium-Gallium-Zinc Oxide Thin-Film Transistor with Source/Drain Regions Doped by Implanted Arsenic”, IEEE Electron Device Lett., vol. 34, no. 1, pp. 60–62, 2013. R. Chowdhury, M.S. Kabir, R.G. Manley, & K.D. Hirschman, “Self-Aligned IGZO TFTs with Boron Implanted Source/Drain Regions”, ECS Transactions, 92(4), 135–142., Oct. 2019. S. Kabir, R. R. Chowdhury, R. G. Manley, and K. D. Hirschman, “Device Structure and Passivation Options for the Integration of Scaled IGZO TFTs,” ECS Trans., vol. 92, no. 4, pp. 143–151, 2019. Figure 1

  • Edge-Directed LTPS Via Flash Lamp Annealing Using a Cr Adhesion Layer for Improved Wettability

    by Glenn Packard, Adam Rosenfeld, Matthew Hum, Robert G. Manley, Karl D. Hirschman

    Flash lamp annealing (FLA) has been explored as an alternative to excimer laser annealed low-temperature polycrystalline silicon (LTPS) for display applications and has shown potential to streamline and decrease the cost of fabrication while maintaining electrical performance [1], [2]. In this method, amorphous silicon is exposed to a single pulse of light emitted from a xenon flash lamp, causing melting and recrystallization in an area of cm2 rather than nm2 in less than a millisecond. FLA has shown value in crystallizing silicon and activating dopants in both PFET and NFET thin-film transistors (TFTs) [3]. However, FLA suffers from inconsistent material uniformity, a consequence of large areas of silicon melting simultaneously. This can cause the molten silicon to de-wet from the oxide or nitride underlayer, leading to the formation of numerous randomized voids. Though previous studies have shown encouraging results when using this void-associated LTPS morphology, improved structure control is necessary to reduce the variance of FLA-LTPS device operation. Edge-directed LTPS has a distinctly different macroscopic morphology than the void associated material, with potential advantages in uniformity and electrical performance. Differences between these morphologies have been previously discussed [4], however in that work the realization of the edge-directed material was hardly intentional and the formation mechanism was not clearly determined. A repeatable and controllable method of producing edge-directed LTPS would effectively solve a key obstacle towards industrial integration of FLA, that of randomly-dispersed irregularities and material nonuniformity. In this work, a replicable morphology of FLA-LTPS is produced and analyzed by using a thin chromium underlayer to promote adhesion without rendering the silicon entirely conductive. With thickness reduced to < 10 nm, Cr does not absorb damaging amounts of energy from the FLA pulse, as opposed to other metal and ceramic layers, which could improve wettability. Chrome has been applied as a silicon underlayer in thin-film photovoltaic applications [5]. The result of this Cr adhesion layer beneath an a-Si mesa during FLA is a characteristic ridge-like pattern of grain formation, as shown in Figure 1A. Large, elongated domains oriented perpendicular to the edges of the silicon mesas are clearly visible. An abrupt ridge is seen equidistant between the long edges of this mesa, with further diagonal ridges present at a 45° angle from the corners. This structure suggests a propagation of crystallization that begins at the edge of the mesas and travels inwards, terminating when it reaches another advancing crystallization front. This structure is only realized when the Cr layer is a continuous film rather than discrete microparticles, suggesting that the effect is due to adhesion rather than metal-induced crystallization. Without this adhesion layer, the randomly-irregular structure seen in Figure 1B is produced. Figure 1C demonstrates atomic force microscopy on this ridge morphology. In this structure, a maximum height differential of around 55 nm between the tops of ridges and the lowest point on the mesa is demonstrated (ignoring scanning artifacts). This is significant, as the original thickness of amorphous silicon as deposited was only 60 nm, suggesting large-scale mass transfer during crystallization. However, dewetting behavior is minimized. The elongated structure, lack of voids, and edge-inward pattern of this morphology is hypothetically consistent with explosive crystallization [6], versus a quasi-equilibrium melt-phase which results in randomly-irregular material. Similar morphology has been demonstrated using excimer laser and continuous-wave laser annealing, in which only a small area of silicon is in liquid phase at any given moment [7], [8]. However, its formation in FLA, in which large areas are melted simultaneously, is an important step towards the commercial viability of flash lamp annealing. This polycrystalline material is being explored as a viable channel material for PFET TFTs. The apparent presence of micrometer-scale grains is expected to improve channel mobility [9], while providing a uniform and predictable structure, thus minimizing variance in device operation. Material properties and electrical characteristics will be presented. Figure 1

  • Flash Lamp Annealed LTPS TFTs with ITO Bottom-Gate Structures

    by Glenn Packard, Adam Rosenfeld, Robert G. Manley, Karl D. Hirschman

    A study on bottom-gate PMOS TFTs built on flash lamp annealed polycrystalline silicon is presented. As an alternative to top-gate devices, bottom-gate TFTs offer potential benefits in dielectric-semiconductor interface quality due to process integration details of crystallization and defect passivation. Indium Tin Oxide was used as the gate electrode material due to its attractive optical and electrical properties, thermal stability, and compatibility with the FLA process. Details of an experimental design used to investigate combinations of FLA and furnace annealing for a-Si crystallization and dopant activation processes will be discussed. ITO Bottom-gate TFTs fabricated with FLA crystallization followed by boron ion implantation and furnace activation exhibited superior electrical characteristics in comparison to other treatments. A comparison of electrical characteristics measured on bottom-gate and double-gate devices is used to develop an interpretation of defect effects and provide a qualitative assessment of interface states.

  • Edge-Directed LTPS Via Flash Lamp Annealing Using a Cr Adhesion Layer for Improved Wettability

    by Glenn Packard, Adam Rosenfeld, Matthew Hum, Robert G. Manley, Karl D. Hirschman

    PMOS TFTs built on flash lamp annealed polycrystalline silicon are presented. A thin layer of chromium is used as an adhesion promoter to prevent randomized voids from forming, allowing predictable grain growth in an elongated morphology oriented away from silicon mesa edges. Operational TFTs were realized, revealing that the Cr under-layer does not result in a significant conductance in parallel with the channel, and effectively serves as a barrier to glass contaminants. The methodology supports the production of TFTs with a high degree of electrical uniformity. Comparisons are made between electrical characteristics of transistors with grains oriented in the same direction as the channel carrier pathway versus those with perpendicular orientation; the former demonstrating approximately ten percent higher channel mobility. Process details and representative electrical characteristics are described.

  • Self-Aligned IGZO TFTs with Boron Implanted Source/Drain Regions

    by Rahnuma Rifat Chowdhury, Muhammad Salahuddin Kabir, Robert G. Manley, Karl D Hirschman

    Self-aligned channel regions in thin-film transistors (TFTs) have advantages in reduced parasitic capacitance and stage delay, and a reduction in overhead real estate. A common method used to fabricate self-aligned a-Si:H TFTs is to utilize a through-glass exposure of photoresist which is blocked by the opaque metal bottom-gate electrode [1,2]. This process does not require an additional photomask or lithographic alignment, and thus supports low production cost. Sputtered IGZO has been introduced into flat panel display product manufacturing, exhibiting a channel mobility of approximately an order of magnitude higher than a-Si:H. The working source/drain electrodes in IGZO TFTs can be direct metal contact regions to the IGZO, without the need for additional processes such as doping to render the IGZO conductive. Proper metallurgy and annealing processes can provide ohmic behavior with minimal series resistance [3], however this usually requires several microns of gate-to-source/drain overlap in order to ensure such behavior. Various self-aligned channel strategies have been demonstrated that either utilize through-glass exposure or a top-gate structure [4,5]; however such methods must address associated process integration challenges. The focus of this study is a novel technique to realize bottom-gate (BG) Indium-Gallium-Zinc Oxide (IGZO) TFTs that is not design-rule dependent or dependent on lithographic alignment. This work presents an alternative method to attain a self-aligned IGZO channel on the traditional staggered BG TFT structure which utilizes top-side exposure and optical thin-film interference. Reflection from the underlying bottom-gate electrode can result in a lower effective exposure of positive-working photoresist, creating a mirror image of the gate electrode in photoresist above the IGZO channel region (see Figure 1). One-dimensional verification of this technique was demonstrated using an underlying molybdenum gate electrode, 100 nm SiO2 gate dielectric, 50 nm IGZO, and AZ MIR 701 positive photoresist imaging layer. Top-side illumination at g-line (λ = 436 nm) with slight underexposure resulted in “reflection gates” that were aligned to the underlying bottom metal electrodes (see Figure 2). This pattern definition can then be used to protect the channel region during subsequent source/drain “activation” processes under investigation which include ion implantation, UV irradiation and plasma exposure [5-7]. Details of the lithographic process, selective source/drain activation, and resulting TFT operation will be presented. [1] K. Asama, T. Kodama, S. Kawai, Y. Nasu, and S.Yanagisawa, “Self-Alignment Processed A-Si TFT Matrix Circuit for LCD Panels”, SID Intl. Symp. Digest of Technical Papers, pp. 144-145, 1983. [2] Y. Kuo, “A New Process Using Two Photo-Masks to Prepare Trilayer Thin Film Transistors”, J. Electrochem. Soc., pp. 138, 1991. [3] T. Mudgal, N. Walsh, R.G. Manley, and K.D. Hirschman, “Impact of Annealing on Contact Formation and Stability of IGZO TFTs,” ECS J. Solid State Sci. Technol. 2014 volume 3, issue 9, Q3032-Q3034 (2014) / DOI: 10.1149/2.006409jss [4] Z. Xia, L. Lu, J. Li, H. S. Kwok, and M. Wong, “A Bottom-Gate Metal-Oxide Thin-Film Transistor With Self-Aligned Source/Drain Regions”, IEEE Trans. Electron Devices, vol. 65, no. 7, pp. 2820–2826, 2018. [5] R. Chen, W. Zhou, M. Zhang, M. Wong, and H. S. Kwok, “Self-Aligned Indium-Gallium-Zinc Oxide Thin-Film Transistor With Source/Drain Regions Doped by Implanted Arsenic”, IEEE Electron Device Lett., vol. 34, no. 1, pp. 60–62, 2013. [6] M.-H. Kim, S.-Y. Choi, S.-H. Jeon, J.-H. Lim, and D.-K. Choi, “Stability Behavior of Self-Aligned Coplanar a-IGZO Thin Film Transistors Fabricated by Deep Ultraviolet Irradiation”, ECS J. Solid State Sci. Technol., vol. 7, no. 4, pp. Q60–Q65, 2018. [7] X. He, L. Wang, X. Xiao, W. Deng, L. Zhang, M. Chan, and S. Zhang, “Implementation of Fully Self-Aligned Homojunction Double-Gate a-IGZO TFTs”, vol. 35, no. 9, pp. 927–929, 2014. Figure 1

  • Device Structure and Passivation Options for the Integration of Scaled IGZO TFTs

    by Muhammad Salahuddin Kabir, Rahnuma Rifat Chowdhury, Robert G. Manley, Karl D Hirschman

    The focus of this work is on the performance dependence of scaled IGZO TFTs with variations in gate electrode configuration and passivation options. A conservative process for the fabrication of long channel length devices (i.e. L ≥ 2 µm) exhibits long-channel behavior and excellent stability in both bottom-gate (BG) and double-gate (DG) configurations [1,2]. As the devices are scaled to shorter channel lengths, limitations of the device electrostatics begin to give way to short channel behavior. Dielectrics used for the gate and back-channel regions are typically adjusted to overcome short-channel effects as lateral dimensions are reduced. However certain interaction effects require additional process modifications for the desired device response and to accommodate the details of process integration. Scaled devices with channel lengths L < 2 µm are under investigation, with process conditions evaluated by quantitative measures on the materials properties, electrostatic behavior, and stability when subjected to bias and thermal stress. Process recipes for PECVD passivation layers, oxygen ambient annealing, and ALD capping materials are under reevaluation for their impact on short-channel devices. TCAD simulation is used as a resource to refine material and device models [3], and provide insight on the details which establish the limits of device operation. Design rule scaling and self-aligned gate device structures are also being studied for reduced parasitic capacitance and stage delay, and a reduction in overhead real estate. [1] T. Mudgal, N. Edwards, P. Ganesh, A. Bharadwaj, Eli Powell, M.S. Pierce, R. G. Manley, and K. D. Hirschman, “Investigation on the Gate Electrode Configuration of IGZO TFTs for Improved Channel Control and Suppression of Bias-Stress Induced Instability”, ECS Trans. 75 (10), 189-197 (2016) [2] M.S. Kabir, P. Ganesh, R.R. Chowdhury, H. Sethupathi, J. Okvath, J. Konowitch, R.G. Manley and K.D. Hirschman, “Channel-length dependent performance degradation of thermally stressed IGZO TFTs”, ECS Trans. 86 (11), 125-133 (2018) DOI: 10.1149/08611.0125ecst [3] K.D. Hirschman, T. Mudgal, E. Powell and R.G. Manley, “A 2D empirical model for on-state operation of scaled IGZO TFTs exemplifying the physical response of TCAD simulation”, ECS Trans. 86 (11), 153-166 (2018) DOI: 10.1149/08611.0153ecst Figure 1

  • Flash Lamp Annealed Polycrystalline Silicon TFT Dependence on Surface Morphology and the Back-Channel Material Interface

    by Glenn Packard, Robert G. Manley, Karl D Hirschman

    This work studies the operation of polycrystalline silicon p-channel TFTs prepared via Flash Lamp Annealing (FLA). Silicon nitride was investigated as a back-channel interface layer to suppress void formation via dewetting of molten silicon. Predefined polygons of amorphous silicon were crystallized on display glass using single-pulse FLA exposure. Two distinct surface morphologies were realized within the same exposed region as a result of the underlying silicon nitride film and localized variation in the substrate thermal contact during PECVD deposition of amorphous silicon. While both resulting morphologies have polysilicon grains on micron scale, differences in TFT electrical behavior appear to coincide with differences in grain structure and boundary regions. The electrical results also indicate inferior electrical performance in response to the back-channel silicon nitride in comparison to results demonstrated on SiO2. Extracted parameters provide a quantitative assessment of the device operation as related to surface morphology and the back-channel material interface.