Muhammad Salahuddin Kabir
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Muhammad Salahuddin Kabir has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Karl D. Hirschman
Rochester Institute of Technology
4 shared publications Rahnuma Rifat Chowdhury
4 shared publications- Robert G. Manley
Corning Research and Development Corporation
4 shared publications
Latest Publications
- 14 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 43 (8) , 1259-1262
Temperature Dependence of Intrinsic Channel Mobility in Indium-Gallium-Zinc-Oxide TFTs
This work reports on the development of a new TCAD material and device model for Indium-Gallium-Zinc-Oxide TFTs that accounts for operation from 150 K to room temperature, over applied gate and drain bias conditions up to 10 V. Specified defect state distributions include oxygen vacancy donors, conduction band-tail acceptor states, and acceptor-like interface traps. The presented model allows the TCAD simulation to account for the behavior of defect states according to defined energy distributions, thus properly regulating the amount of free channel charge. An intrinsic channel mobility defined as only a function of temperature was found to accurately represent extended state transport. The intrinsic channel mobility was 19 cm 2 /V•s at room temperature, with a reduction to 9 cm 2 /V•s at T = 150 K. The functional dependence reflects a thermally-activated diffusive mobility with a distinct activation energy E a = 40 meV, that is shown to be independent of the Fermi level.
- 14 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 43 (8) , 1259-1262
Temperature Dependence of Intrinsic Channel Mobility in Indium-Gallium-Zinc-Oxide TFTs
This work reports on the development of a new TCAD material and device model for Indium-Gallium-Zinc-Oxide TFTs that accounts for operation from 150 K to room temperature, over applied gate and drain bias conditions up to 10 V. Specified defect state distributions include oxygen vacancy donors, conduction band-tail acceptor states, and acceptor-like interface traps. The presented model allows the TCAD simulation to account for the behavior of defect states according to defined energy distributions, thus properly regulating the amount of free channel charge. An intrinsic channel mobility defined as only a function of temperature was found to accurately represent extended state transport. The intrinsic channel mobility was 19 cm 2 /V•s at room temperature, with a reduction to 9 cm 2 /V•s at T = 150 K. The functional dependence reflects a thermally-activated diffusive mobility with a distinct activation energy E a = 40 meV, that is shown to be independent of the Fermi level.
- 23 November 2020
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2020-02 (28) , 1925
Interpretation of Donor Activation in Boron and Argon Implanted Self-Aligned Bottom-Gate IGZO TFTs
The source/drain electrodes in IGZO TFTs (thin-film transistors) can be direct metal overlapping the IGZO region. However, to achieve ohmic behavior with minimal resistance and ensure tolerance to overlay error, several microns of gate overlap is required. IGZO TFTs with self-aligned channel regions have advantages in reduced parasitic capacitance and stage delay, and a reduction in overhead real estate. Several techniques have been used to selectively form conductive IGZO regions including the introduction of hydrogen [1, 2], plasma exposure [3] and ion implantation [4, 5]. This work provides an interpretation of donor activation in self-aligned bottom-gate (SA-BG) IGZO TFTs with ion-implantation of boron (11B+) and argon (40Ar+) species as the source/drain treatment. Preliminary work investigated a top-gate electrode configuration, which served as the implant mask for the self-aligned strategy. These devices exhibited a significant left-shift in the ID-VGS transfer characteristics that was attributed to charge accumulation on the metal gate, subjecting the gate dielectric to a high electric field and the creation of ionized defects [5]. The bottom-gate implementation utilizes the opaque gate electrode as a mask for a through-wafer exposure of positive photoresist, providing a perfectly aligned implant mask that averted this charging mechanism. Both 11B+ and 40Ar+ implanted SA-BG devices exhibited electrical characteristics that were consistent with non-SA devices [6], with minimal impact of added series resistance. However, there were noted differences in the device operation that became pronounced following thermal stress treatments below 200 °C. Hypotheses in the mechanisms involved with donor activation have been developed from both similarities and differences in electrical behavior. Results suggest a defect-induced mechanism is responsible for implant activation with 40Ar+, whereas implant activation with 11B+ is attributed to the formation of an electrically active donor species involving chemical bonding. Examination of characteristics measured before and after applied thermal stress will be used to explain the interpretation, with the additional support of SIMS and XPS analysis. References H. Wu, H. H. Hsieh, C. W. Chien, and C. C. Wu, “Self-aligned top-gate coplanar In–Ga–Zn–O thin-film transistors,” J. Display Technol., vol.5, no. 12, pp. 515–519, Dec. 2009. H. Kang, I. Kang, S. H. Ryu, and J. Jang, “Self-aligned coplanar a-IGZO TFTs and application to high-speed circuits,” IEEE Electron Device Lett., vol. 32, no. 10, pp. 1385–1387, Oct. 2011. Park, I. Song, S. Kim, S. Kim, C. Kim, J. Lee, H. Lee, E. Lee, H. Yin, K. Kim, K. Kwon, and Y. Park, “Self-aligned top-gate amorphous gallium indium zinc oxide thin film transistors,” Appl. Phys. Lett., vol. 93, no. 5, p. 053501, Aug. 2008. Chen, W. Zhou, M. Zhang, M. Wong, and H. S. Kwok, “Self-Aligned Indium-Gallium-Zinc Oxide Thin-Film Transistor with Source/Drain Regions Doped by Implanted Arsenic”, IEEE Electron Device Lett., vol. 34, no. 1, pp. 60–62, 2013. R. Chowdhury, M.S. Kabir, R.G. Manley, & K.D. Hirschman, “Self-Aligned IGZO TFTs with Boron Implanted Source/Drain Regions”, ECS Transactions, 92(4), 135–142., Oct. 2019. S. Kabir, R. R. Chowdhury, R. G. Manley, and K. D. Hirschman, “Device Structure and Passivation Options for the Integration of Scaled IGZO TFTs,” ECS Trans., vol. 92, no. 4, pp. 143–151, 2019. Figure 1
- 23 November 2020
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2020-02 (28) , 1925
Interpretation of Donor Activation in Boron and Argon Implanted Self-Aligned Bottom-Gate IGZO TFTs
The source/drain electrodes in IGZO TFTs (thin-film transistors) can be direct metal overlapping the IGZO region. However, to achieve ohmic behavior with minimal resistance and ensure tolerance to overlay error, several microns of gate overlap is required. IGZO TFTs with self-aligned channel regions have advantages in reduced parasitic capacitance and stage delay, and a reduction in overhead real estate. Several techniques have been used to selectively form conductive IGZO regions including the introduction of hydrogen [1, 2], plasma exposure [3] and ion implantation [4, 5]. This work provides an interpretation of donor activation in self-aligned bottom-gate (SA-BG) IGZO TFTs with ion-implantation of boron (11B+) and argon (40Ar+) species as the source/drain treatment. Preliminary work investigated a top-gate electrode configuration, which served as the implant mask for the self-aligned strategy. These devices exhibited a significant left-shift in the ID-VGS transfer characteristics that was attributed to charge accumulation on the metal gate, subjecting the gate dielectric to a high electric field and the creation of ionized defects [5]. The bottom-gate implementation utilizes the opaque gate electrode as a mask for a through-wafer exposure of positive photoresist, providing a perfectly aligned implant mask that averted this charging mechanism. Both 11B+ and 40Ar+ implanted SA-BG devices exhibited electrical characteristics that were consistent with non-SA devices [6], with minimal impact of added series resistance. However, there were noted differences in the device operation that became pronounced following thermal stress treatments below 200 °C. Hypotheses in the mechanisms involved with donor activation have been developed from both similarities and differences in electrical behavior. Results suggest a defect-induced mechanism is responsible for implant activation with 40Ar+, whereas implant activation with 11B+ is attributed to the formation of an electrically active donor species involving chemical bonding. Examination of characteristics measured before and after applied thermal stress will be used to explain the interpretation, with the additional support of SIMS and XPS analysis. References H. Wu, H. H. Hsieh, C. W. Chien, and C. C. Wu, “Self-aligned top-gate coplanar In–Ga–Zn–O thin-film transistors,” J. Display Technol., vol.5, no. 12, pp. 515–519, Dec. 2009. H. Kang, I. Kang, S. H. Ryu, and J. Jang, “Self-aligned coplanar a-IGZO TFTs and application to high-speed circuits,” IEEE Electron Device Lett., vol. 32, no. 10, pp. 1385–1387, Oct. 2011. Park, I. Song, S. Kim, S. Kim, C. Kim, J. Lee, H. Lee, E. Lee, H. Yin, K. Kim, K. Kwon, and Y. Park, “Self-aligned top-gate amorphous gallium indium zinc oxide thin film transistors,” Appl. Phys. Lett., vol. 93, no. 5, p. 053501, Aug. 2008. Chen, W. Zhou, M. Zhang, M. Wong, and H. S. Kwok, “Self-Aligned Indium-Gallium-Zinc Oxide Thin-Film Transistor with Source/Drain Regions Doped by Implanted Arsenic”, IEEE Electron Device Lett., vol. 34, no. 1, pp. 60–62, 2013. R. Chowdhury, M.S. Kabir, R.G. Manley, & K.D. Hirschman, “Self-Aligned IGZO TFTs with Boron Implanted Source/Drain Regions”, ECS Transactions, 92(4), 135–142., Oct. 2019. S. Kabir, R. R. Chowdhury, R. G. Manley, and K. D. Hirschman, “Device Structure and Passivation Options for the Integration of Scaled IGZO TFTs,” ECS Trans., vol. 92, no. 4, pp. 143–151, 2019. Figure 1
- 1 September 2019
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2019-02 (25) , 1178
Self-Aligned IGZO TFTs with Boron Implanted Source/Drain Regions
Self-aligned channel regions in thin-film transistors (TFTs) have advantages in reduced parasitic capacitance and stage delay, and a reduction in overhead real estate. A common method used to fabricate self-aligned a-Si:H TFTs is to utilize a through-glass exposure of photoresist which is blocked by the opaque metal bottom-gate electrode [1,2]. This process does not require an additional photomask or lithographic alignment, and thus supports low production cost. Sputtered IGZO has been introduced into flat panel display product manufacturing, exhibiting a channel mobility of approximately an order of magnitude higher than a-Si:H. The working source/drain electrodes in IGZO TFTs can be direct metal contact regions to the IGZO, without the need for additional processes such as doping to render the IGZO conductive. Proper metallurgy and annealing processes can provide ohmic behavior with minimal series resistance [3], however this usually requires several microns of gate-to-source/drain overlap in order to ensure such behavior. Various self-aligned channel strategies have been demonstrated that either utilize through-glass exposure or a top-gate structure [4,5]; however such methods must address associated process integration challenges. The focus of this study is a novel technique to realize bottom-gate (BG) Indium-Gallium-Zinc Oxide (IGZO) TFTs that is not design-rule dependent or dependent on lithographic alignment. This work presents an alternative method to attain a self-aligned IGZO channel on the traditional staggered BG TFT structure which utilizes top-side exposure and optical thin-film interference. Reflection from the underlying bottom-gate electrode can result in a lower effective exposure of positive-working photoresist, creating a mirror image of the gate electrode in photoresist above the IGZO channel region (see Figure 1). One-dimensional verification of this technique was demonstrated using an underlying molybdenum gate electrode, 100 nm SiO2 gate dielectric, 50 nm IGZO, and AZ MIR 701 positive photoresist imaging layer. Top-side illumination at g-line (λ = 436 nm) with slight underexposure resulted in “reflection gates” that were aligned to the underlying bottom metal electrodes (see Figure 2). This pattern definition can then be used to protect the channel region during subsequent source/drain “activation” processes under investigation which include ion implantation, UV irradiation and plasma exposure [5-7]. Details of the lithographic process, selective source/drain activation, and resulting TFT operation will be presented. [1] K. Asama, T. Kodama, S. Kawai, Y. Nasu, and S.Yanagisawa, “Self-Alignment Processed A-Si TFT Matrix Circuit for LCD Panels”, SID Intl. Symp. Digest of Technical Papers, pp. 144-145, 1983. [2] Y. Kuo, “A New Process Using Two Photo-Masks to Prepare Trilayer Thin Film Transistors”, J. Electrochem. Soc., pp. 138, 1991. [3] T. Mudgal, N. Walsh, R.G. Manley, and K.D. Hirschman, “Impact of Annealing on Contact Formation and Stability of IGZO TFTs,” ECS J. Solid State Sci. Technol. 2014 volume 3, issue 9, Q3032-Q3034 (2014) / DOI: 10.1149/2.006409jss [4] Z. Xia, L. Lu, J. Li, H. S. Kwok, and M. Wong, “A Bottom-Gate Metal-Oxide Thin-Film Transistor With Self-Aligned Source/Drain Regions”, IEEE Trans. Electron Devices, vol. 65, no. 7, pp. 2820–2826, 2018. [5] R. Chen, W. Zhou, M. Zhang, M. Wong, and H. S. Kwok, “Self-Aligned Indium-Gallium-Zinc Oxide Thin-Film Transistor With Source/Drain Regions Doped by Implanted Arsenic”, IEEE Electron Device Lett., vol. 34, no. 1, pp. 60–62, 2013. [6] M.-H. Kim, S.-Y. Choi, S.-H. Jeon, J.-H. Lim, and D.-K. Choi, “Stability Behavior of Self-Aligned Coplanar a-IGZO Thin Film Transistors Fabricated by Deep Ultraviolet Irradiation”, ECS J. Solid State Sci. Technol., vol. 7, no. 4, pp. Q60–Q65, 2018. [7] X. He, L. Wang, X. Xiao, W. Deng, L. Zhang, M. Chan, and S. Zhang, “Implementation of Fully Self-Aligned Homojunction Double-Gate a-IGZO TFTs”, vol. 35, no. 9, pp. 927–929, 2014. Figure 1
- 1 September 2019
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2019-02 (25) , 1178
Self-Aligned IGZO TFTs with Boron Implanted Source/Drain Regions
Self-aligned channel regions in thin-film transistors (TFTs) have advantages in reduced parasitic capacitance and stage delay, and a reduction in overhead real estate. A common method used to fabricate self-aligned a-Si:H TFTs is to utilize a through-glass exposure of photoresist which is blocked by the opaque metal bottom-gate electrode [1,2]. This process does not require an additional photomask or lithographic alignment, and thus supports low production cost. Sputtered IGZO has been introduced into flat panel display product manufacturing, exhibiting a channel mobility of approximately an order of magnitude higher than a-Si:H. The working source/drain electrodes in IGZO TFTs can be direct metal contact regions to the IGZO, without the need for additional processes such as doping to render the IGZO conductive. Proper metallurgy and annealing processes can provide ohmic behavior with minimal series resistance [3], however this usually requires several microns of gate-to-source/drain overlap in order to ensure such behavior. Various self-aligned channel strategies have been demonstrated that either utilize through-glass exposure or a top-gate structure [4,5]; however such methods must address associated process integration challenges. The focus of this study is a novel technique to realize bottom-gate (BG) Indium-Gallium-Zinc Oxide (IGZO) TFTs that is not design-rule dependent or dependent on lithographic alignment. This work presents an alternative method to attain a self-aligned IGZO channel on the traditional staggered BG TFT structure which utilizes top-side exposure and optical thin-film interference. Reflection from the underlying bottom-gate electrode can result in a lower effective exposure of positive-working photoresist, creating a mirror image of the gate electrode in photoresist above the IGZO channel region (see Figure 1). One-dimensional verification of this technique was demonstrated using an underlying molybdenum gate electrode, 100 nm SiO2 gate dielectric, 50 nm IGZO, and AZ MIR 701 positive photoresist imaging layer. Top-side illumination at g-line (λ = 436 nm) with slight underexposure resulted in “reflection gates” that were aligned to the underlying bottom metal electrodes (see Figure 2). This pattern definition can then be used to protect the channel region during subsequent source/drain “activation” processes under investigation which include ion implantation, UV irradiation and plasma exposure [5-7]. Details of the lithographic process, selective source/drain activation, and resulting TFT operation will be presented. [1] K. Asama, T. Kodama, S. Kawai, Y. Nasu, and S.Yanagisawa, “Self-Alignment Processed A-Si TFT Matrix Circuit for LCD Panels”, SID Intl. Symp. Digest of Technical Papers, pp. 144-145, 1983. [2] Y. Kuo, “A New Process Using Two Photo-Masks to Prepare Trilayer Thin Film Transistors”, J. Electrochem. Soc., pp. 138, 1991. [3] T. Mudgal, N. Walsh, R.G. Manley, and K.D. Hirschman, “Impact of Annealing on Contact Formation and Stability of IGZO TFTs,” ECS J. Solid State Sci. Technol. 2014 volume 3, issue 9, Q3032-Q3034 (2014) / DOI: 10.1149/2.006409jss [4] Z. Xia, L. Lu, J. Li, H. S. Kwok, and M. Wong, “A Bottom-Gate Metal-Oxide Thin-Film Transistor With Self-Aligned Source/Drain Regions”, IEEE Trans. Electron Devices, vol. 65, no. 7, pp. 2820–2826, 2018. [5] R. Chen, W. Zhou, M. Zhang, M. Wong, and H. S. Kwok, “Self-Aligned Indium-Gallium-Zinc Oxide Thin-Film Transistor With Source/Drain Regions Doped by Implanted Arsenic”, IEEE Electron Device Lett., vol. 34, no. 1, pp. 60–62, 2013. [6] M.-H. Kim, S.-Y. Choi, S.-H. Jeon, J.-H. Lim, and D.-K. Choi, “Stability Behavior of Self-Aligned Coplanar a-IGZO Thin Film Transistors Fabricated by Deep Ultraviolet Irradiation”, ECS J. Solid State Sci. Technol., vol. 7, no. 4, pp. Q60–Q65, 2018. [7] X. He, L. Wang, X. Xiao, W. Deng, L. Zhang, M. Chan, and S. Zhang, “Implementation of Fully Self-Aligned Homojunction Double-Gate a-IGZO TFTs”, vol. 35, no. 9, pp. 927–929, 2014. Figure 1
- 1 September 2019
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2019-02 (25) , 1180
Device Structure and Passivation Options for the Integration of Scaled IGZO TFTs
The focus of this work is on the performance dependence of scaled IGZO TFTs with variations in gate electrode configuration and passivation options. A conservative process for the fabrication of long channel length devices (i.e. L ≥ 2 µm) exhibits long-channel behavior and excellent stability in both bottom-gate (BG) and double-gate (DG) configurations [1,2]. As the devices are scaled to shorter channel lengths, limitations of the device electrostatics begin to give way to short channel behavior. Dielectrics used for the gate and back-channel regions are typically adjusted to overcome short-channel effects as lateral dimensions are reduced. However certain interaction effects require additional process modifications for the desired device response and to accommodate the details of process integration. Scaled devices with channel lengths L < 2 µm are under investigation, with process conditions evaluated by quantitative measures on the materials properties, electrostatic behavior, and stability when subjected to bias and thermal stress. Process recipes for PECVD passivation layers, oxygen ambient annealing, and ALD capping materials are under reevaluation for their impact on short-channel devices. TCAD simulation is used as a resource to refine material and device models [3], and provide insight on the details which establish the limits of device operation. Design rule scaling and self-aligned gate device structures are also being studied for reduced parasitic capacitance and stage delay, and a reduction in overhead real estate. [1] T. Mudgal, N. Edwards, P. Ganesh, A. Bharadwaj, Eli Powell, M.S. Pierce, R. G. Manley, and K. D. Hirschman, “Investigation on the Gate Electrode Configuration of IGZO TFTs for Improved Channel Control and Suppression of Bias-Stress Induced Instability”, ECS Trans. 75 (10), 189-197 (2016) [2] M.S. Kabir, P. Ganesh, R.R. Chowdhury, H. Sethupathi, J. Okvath, J. Konowitch, R.G. Manley and K.D. Hirschman, “Channel-length dependent performance degradation of thermally stressed IGZO TFTs”, ECS Trans. 86 (11), 125-133 (2018) DOI: 10.1149/08611.0125ecst [3] K.D. Hirschman, T. Mudgal, E. Powell and R.G. Manley, “A 2D empirical model for on-state operation of scaled IGZO TFTs exemplifying the physical response of TCAD simulation”, ECS Trans. 86 (11), 153-166 (2018) DOI: 10.1149/08611.0153ecst Figure 1
- 1 September 2019
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2019-02 (25) , 1180
Device Structure and Passivation Options for the Integration of Scaled IGZO TFTs
The focus of this work is on the performance dependence of scaled IGZO TFTs with variations in gate electrode configuration and passivation options. A conservative process for the fabrication of long channel length devices (i.e. L ≥ 2 µm) exhibits long-channel behavior and excellent stability in both bottom-gate (BG) and double-gate (DG) configurations [1,2]. As the devices are scaled to shorter channel lengths, limitations of the device electrostatics begin to give way to short channel behavior. Dielectrics used for the gate and back-channel regions are typically adjusted to overcome short-channel effects as lateral dimensions are reduced. However certain interaction effects require additional process modifications for the desired device response and to accommodate the details of process integration. Scaled devices with channel lengths L < 2 µm are under investigation, with process conditions evaluated by quantitative measures on the materials properties, electrostatic behavior, and stability when subjected to bias and thermal stress. Process recipes for PECVD passivation layers, oxygen ambient annealing, and ALD capping materials are under reevaluation for their impact on short-channel devices. TCAD simulation is used as a resource to refine material and device models [3], and provide insight on the details which establish the limits of device operation. Design rule scaling and self-aligned gate device structures are also being studied for reduced parasitic capacitance and stage delay, and a reduction in overhead real estate. [1] T. Mudgal, N. Edwards, P. Ganesh, A. Bharadwaj, Eli Powell, M.S. Pierce, R. G. Manley, and K. D. Hirschman, “Investigation on the Gate Electrode Configuration of IGZO TFTs for Improved Channel Control and Suppression of Bias-Stress Induced Instability”, ECS Trans. 75 (10), 189-197 (2016) [2] M.S. Kabir, P. Ganesh, R.R. Chowdhury, H. Sethupathi, J. Okvath, J. Konowitch, R.G. Manley and K.D. Hirschman, “Channel-length dependent performance degradation of thermally stressed IGZO TFTs”, ECS Trans. 86 (11), 125-133 (2018) DOI: 10.1149/08611.0125ecst [3] K.D. Hirschman, T. Mudgal, E. Powell and R.G. Manley, “A 2D empirical model for on-state operation of scaled IGZO TFTs exemplifying the physical response of TCAD simulation”, ECS Trans. 86 (11), 153-166 (2018) DOI: 10.1149/08611.0153ecst Figure 1
- 1 May 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Electrification of streets of Dhaka city using solar and piezoelectric energy
This research paper carries out a proposal to implement an efficient way to electrify the streets of Dhaka, the capital of Bangladesh, using solar power. Recently, government has launched a project named “Solar Photovoltaic-Powered LED (Light Emitting Diode) Street Lighting” to electrify the streets of Dhaka using only solar panels. Under the prevailing project, 122 LED lights, each of 30W are installed to electrify approximately 2 km streets. But after implementation, it has been found that 60-100W LED light is required for adequately illuminating the streets which will allow the ADB fund to cover only 250-300 km streets. Our proposal is to use the solar panels implemented in this project more efficiently and to carry out a realistic experimental approach to enhance the solar output power to a significant level with the application of solar concentrator and piezoelectric energy harvesting circuit. The method is arranged using `Double Sun Technology'. A remarkable enhancement in the output power is achieved with this method. Rather than using only a solar panel, the output power increases by 12.14% by using a photovoltaic (PV) panel with two flat mirrors as concentrator. To implement the project more efficiently, the concept of piezoelectricity have been introduced. In this paper, piezoelectric-based energy-harvesting technology is applied to generate electricity from roadways. The piezoelectric energy harvesting circuit was designed and simulated in PSPICE. A voltage doubler and a bridge rectifier were wired to the equivalent circuit model of the piezoelectric materials. The vibration present on the roadways from the movement of the vehicles was applied in the form of voltage to the energy harvesting circuit. The goal of this experiment is to investigate whether piezoelectricity would be able to provide sufficient source of voltage to charge the parent battery in case of rainy or cloudy days.
- 1 May 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Electrification of streets of Dhaka city using solar and piezoelectric energy
This research paper carries out a proposal to implement an efficient way to electrify the streets of Dhaka, the capital of Bangladesh, using solar power. Recently, government has launched a project named “Solar Photovoltaic-Powered LED (Light Emitting Diode) Street Lighting” to electrify the streets of Dhaka using only solar panels. Under the prevailing project, 122 LED lights, each of 30W are installed to electrify approximately 2 km streets. But after implementation, it has been found that 60-100W LED light is required for adequately illuminating the streets which will allow the ADB fund to cover only 250-300 km streets. Our proposal is to use the solar panels implemented in this project more efficiently and to carry out a realistic experimental approach to enhance the solar output power to a significant level with the application of solar concentrator and piezoelectric energy harvesting circuit. The method is arranged using `Double Sun Technology'. A remarkable enhancement in the output power is achieved with this method. Rather than using only a solar panel, the output power increases by 12.14% by using a photovoltaic (PV) panel with two flat mirrors as concentrator. To implement the project more efficiently, the concept of piezoelectricity have been introduced. In this paper, piezoelectric-based energy-harvesting technology is applied to generate electricity from roadways. The piezoelectric energy harvesting circuit was designed and simulated in PSPICE. A voltage doubler and a bridge rectifier were wired to the equivalent circuit model of the piezoelectric materials. The vibration present on the roadways from the movement of the vehicles was applied in the form of voltage to the energy harvesting circuit. The goal of this experiment is to investigate whether piezoelectricity would be able to provide sufficient source of voltage to charge the parent battery in case of rainy or cloudy days.