S. Lakshmana Kumar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
S. Lakshmana Kumar has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Bommi Rammohan
Department of ECE, Chennai Institute of Technology, Chennai, India
2 shared publications R. Raj Jawahar
2 shared publications- Annamalai Mahendran
Sona College of Technology
1 shared publication - Chakaravarthy Ezilarasan
Center for Applied Research, Chennai Institute of Technology, Chennai, India
1 shared publication Dynamech Design Solutions Ceo
1 shared publication- M. Thenmozhi
Department of Computer Science, Sona College of Arts and science, Salem, India
1 shared publication
Latest Publications
- Open Access
- 16 June 2022
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2022, 1-11
A Machine Learning Approach to Optimize, Model, and Predict the Machining Factors in Dry Drilling of Nimonic C263
In this present paper, the machine learning approach is used to optimize, model, and predict the factors during drilling Nimonic C263 under dry mode. Nimonic C263 is tough to machine aero alloys, and it is required to find a predictive model and to optimize the factors in drilling this alloy before the actual machining process. It helps to avoid the actual machining cost and material cost. Experimental trails are planned based on Taguchi analysis, and L27 orthogonal array was chosen. Speed, feed, and approach angle of drill were considered as controlling factors, and cutting force and surface roughness were considered as responses. The feed forward neural network (FFNN) was used to develop a predictive model. The prediction capability was validated with a predictive model developed by Taguchi analysis. Furthermore, ANOVA (analysis of variance) analysis was done to find out the most influence factor on the responses.
- 16 June 2022
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2022, 1-11
Open AccessA Machine Learning Approach to Optimize, Model, and Predict the Machining Factors in Dry Drilling of Nimonic C263
In this present paper, the machine learning approach is used to optimize, model, and predict the factors during drilling Nimonic C263 under dry mode. Nimonic C263 is tough to machine aero alloys, and it is required to find a predictive model and to optimize the factors in drilling this alloy before the actual machining process. It helps to avoid the actual machining cost and material cost. Experimental trails are planned based on Taguchi analysis, and L27 orthogonal array was chosen. Speed, feed, and approach angle of drill were considered as controlling factors, and cutting force and surface roughness were considered as responses. The feed forward neural network (FFNN) was used to develop a predictive model. The prediction capability was validated with a predictive model developed by Taguchi analysis. Furthermore, ANOVA (analysis of variance) analysis was done to find out the most influence factor on the responses.
- Open Access
- 1 January 2022
- Published by Wiley in Journal of Nanomaterials
- Vol. 2022 (1)
Surface Roughness Evaluation in Turning of Nimonic C263 Super Alloy Using 2D DWT Histogram Equalization
Surface roughness of specimens is an important area of research since it influences the performance of machined parts. Meanwhile, employing a vision system to judge the roughness of the machined surface of specimens via captured images acquired from the specimen is an innovative and extensively used method. In this investigation, a vision system is used to capture the SEM images of the machined surface. The two‐dimensional images of the machined surface of the Nimonic263 alloy are used to approximate the profile of the surface of specimens in finish turning. Surface roughness was detected in simulated images of specimens in a variety of machining conditions using the imaging technology. In this research work, the surface texture is extracted using a technique that combines 2D surface images and wavelet transform approach. The 2D wavelet transform has the capability to disintegrate a machined surface image into multiresolution depiction for several surface characteristics and can be utilized for surface evaluation. The difference in the histogram frequency of an illuminated region of interest (ROI) from turned surface images was analyzed to aid in the evaluation of surface roughness with an average prediction error of less than 3.2%.
- 1 January 2022
- Published by Wiley in Journal of Nanomaterials
- Vol. 2022 (1)
Open AccessSurface Roughness Evaluation in Turning of Nimonic C263 Super Alloy Using 2D DWT Histogram Equalization
Surface roughness of specimens is an important area of research since it influences the performance of machined parts. Meanwhile, employing a vision system to judge the roughness of the machined surface of specimens via captured images acquired from the specimen is an innovative and extensively used method. In this investigation, a vision system is used to capture the SEM images of the machined surface. The two‐dimensional images of the machined surface of the Nimonic263 alloy are used to approximate the profile of the surface of specimens in finish turning. Surface roughness was detected in simulated images of specimens in a variety of machining conditions using the imaging technology. In this research work, the surface texture is extracted using a technique that combines 2D surface images and wavelet transform approach. The 2D wavelet transform has the capability to disintegrate a machined surface image into multiresolution depiction for several surface characteristics and can be utilized for surface evaluation. The difference in the histogram frequency of an illuminated region of interest (ROI) from turned surface images was analyzed to aid in the evaluation of surface roughness with an average prediction error of less than 3.2%.
- 30 January 2020
- Published by Blue Eyes Intelligence Engineering and Sciences Engineering and Sciences Publication (BEIESP) in International Journal of Recent Technology and Engineering (IJRTE)
- Vol. 8 (5) , 1929-1937
Prediction of Paper Mill Wastewater Treatment Process Parameters in Sequencing Batch Reactor using Fuzzy Logic Technique
Integrated paper and pulp mills utilize logs and wood chips for the production of paper. During the process, the expose of raw effluents affect the environmental factors. In this analysis, waste water from paper mills was processed with the SBR (sequencing batch reactor) cycle. The effect of microbes and aeration periods with varying amounts of waste water on the efficiency of SBRs has been evaluated. During the tests, removal efficiencies of COD, BOD and TDS have been tracked. For experimental design, study and optimization, Box-Behnken core composite architecture was implemented. To maximize SBR performance, Fuzzy logic control was used. The SBR demonstrated higher efficiency in removal output on the basis of the tests. At the optimum conditions of microbe dosage of 55 ml aeration time of 5 hrs and wastewater concentration of 75% and the SBR achieved maximum removal percentage of COD, BOD and TDSis 88.18%, 91.80% and 87.12%respectively.
- 30 January 2020
- Published by Blue Eyes Intelligence Engineering and Sciences Engineering and Sciences Publication (BEIESP) in International Journal of Recent Technology and Engineering (IJRTE)
- Vol. 8 (5) , 1929-1937
Prediction of Paper Mill Wastewater Treatment Process Parameters in Sequencing Batch Reactor using Fuzzy Logic Technique
Integrated paper and pulp mills utilize logs and wood chips for the production of paper. During the process, the expose of raw effluents affect the environmental factors. In this analysis, waste water from paper mills was processed with the SBR (sequencing batch reactor) cycle. The effect of microbes and aeration periods with varying amounts of waste water on the efficiency of SBRs has been evaluated. During the tests, removal efficiencies of COD, BOD and TDS have been tracked. For experimental design, study and optimization, Box-Behnken core composite architecture was implemented. To maximize SBR performance, Fuzzy logic control was used. The SBR demonstrated higher efficiency in removal output on the basis of the tests. At the optimum conditions of microbe dosage of 55 ml aeration time of 5 hrs and wastewater concentration of 75% and the SBR achieved maximum removal percentage of COD, BOD and TDSis 88.18%, 91.80% and 87.12%respectively.
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 33, 833-838
Characterization of waste plastic oil as biodiesel in IC engines
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 33, 833-838
Characterization of waste plastic oil as biodiesel in IC engines