Indra Sidharta
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Indra Sidharta has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Muhammad Nur Yuniarto
Institut Teknologi Sepuluh Nopember Jl, AriefRahmanHakim
2 shared publications - Yoga Uta Nugraha
Departemen Teknik, Fakultas Teknologi Maju dan Multidisiplin, Universitas Airlangga
2 shared publications Auzan Adani Devara
Department of Mechanical Engineering, ITS, Surabaya, Indonesia
1 shared publication- Dimas Anton Asfani
Department of Electrical Engineering, Institut Teknologi Sepuluh Nopember, Surabaya, Indonesia
1 shared publication Indra Surya Iwanata
Department of Mechanical Engineering, Institut Teknologi Sepuluh Nopember (ITS), Surabaya, Indonesia
1 shared publicationJothan Agus Haryono
Department of Mechanical Engineering, ITS, Surabaya, Indonesia
1 shared publication
Latest Publications
- 5 August 2026
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 40 (8) , 5753-5762
Effects of the buttering layer and post-weld heat treatment on the mechanical properties of dissimilar welding T91 and 347H
- 5 August 2026
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 40 (8) , 5753-5762
Effects of the buttering layer and post-weld heat treatment on the mechanical properties of dissimilar welding T91 and 347H
- Open Access
- 20 June 2022
- Published by MDPI AG in World Electric Vehicle Journal
- Vol. 13 (6) , 107
On the Development and Experimental Validation of a Novel and Intuitive Interior Permanent Magnet Synchronous Motor Controller for Electric Vehicle Application
This paper discusses the process of developing a novel and robust algorithm for an interior permanent magnet synchronous motor controller. This is necessary for the simplification of the setting of control parameters and maintaining the proper operation of the motor. A 3D torque lookup table was used in which two inputs were considered, i.e., accelerator movements and the motor rotational speed. These two inputs allowed the lookup table to generate a specified torque at any motor rotation, which was then fed-forward to the field-oriented control and space vector pulse width modulation algorithm. Modeling, simulation, and experimental tests were performed to design and validate the proposed controller. The experimental validation shows that the proposed controller worked as intended. This was indicated by its ability to control the motor to obtain a 7% higher torque output than in the simulation in the constant torque region. In the field-weakening region, the controller could make the motor reach a maximum speed of 5500 RPM. There was only an 8% difference compared to the simulation (6500 RPM). In terms of maximum power generated, the controller was able to match the simulation output with only a 5% difference.
- 20 June 2022
- Published by MDPI AG in World Electric Vehicle Journal
- Vol. 13 (6) , 107
Open AccessOn the Development and Experimental Validation of a Novel and Intuitive Interior Permanent Magnet Synchronous Motor Controller for Electric Vehicle Application
This paper discusses the process of developing a novel and robust algorithm for an interior permanent magnet synchronous motor controller. This is necessary for the simplification of the setting of control parameters and maintaining the proper operation of the motor. A 3D torque lookup table was used in which two inputs were considered, i.e., accelerator movements and the motor rotational speed. These two inputs allowed the lookup table to generate a specified torque at any motor rotation, which was then fed-forward to the field-oriented control and space vector pulse width modulation algorithm. Modeling, simulation, and experimental tests were performed to design and validate the proposed controller. The experimental validation shows that the proposed controller worked as intended. This was indicated by its ability to control the motor to obtain a 7% higher torque output than in the simulation in the constant torque region. In the field-weakening region, the controller could make the motor reach a maximum speed of 5500 RPM. There was only an 8% difference compared to the simulation (6500 RPM). In terms of maximum power generated, the controller was able to match the simulation output with only a 5% difference.
- 4 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electrification Magazine
- Vol. 10 (1) , 65-74
Indonesian Electric Motorcycle Development: Lessons from innovation-based concept implementation on the design and production of the first Indonesian electric motorcycle
The R&D lead time of a motorcycle from scratch takes roughly five to seven years. This time frame needs to be significantly reduced to develop and produce an electric motorcycle in less than a year. The purpose of this article is to report the designing, testing, and mass production of GESITS, the first electric motorcycle developed in Indonesia. This was a significant development in Indonesian industries because motorcycles before GESISTS were developed by their principal engineers in Japan, India, or China. Due to the short time available for R&D, traditional methods employed by existing automotive industries were not applicable. They operated following the requirements from their motorcycle parent companies, which had gigantic markets, capabilities, and finance. Furthermore, the electric motorcycle industry was not yet ready because the R&D model seemed to be a push rather than pull market production employed by the existing industries. Therefore, a novel methodology and approaches for R&D and production are required. In terms of technology, business model, and company, this motorcycle was novel, meaning it was logical to implement the innovation-based approach to research, develop, and produce the GESITS. Lean start-up methodology governs the R&D process and was used to develop GESITS and its business model in less than two years. Subsequently, GESITS has been mass produced and sold in Indonesia and abroad with sales significantly increasing annually. Therefore, this article shows the successful implementation of the innovation-based concept in new industries—electrical motorcycles.
- 4 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electrification Magazine
- Vol. 10 (1) , 65-74
Indonesian Electric Motorcycle Development: Lessons from innovation-based concept implementation on the design and production of the first Indonesian electric motorcycle
The R&D lead time of a motorcycle from scratch takes roughly five to seven years. This time frame needs to be significantly reduced to develop and produce an electric motorcycle in less than a year. The purpose of this article is to report the designing, testing, and mass production of GESITS, the first electric motorcycle developed in Indonesia. This was a significant development in Indonesian industries because motorcycles before GESISTS were developed by their principal engineers in Japan, India, or China. Due to the short time available for R&D, traditional methods employed by existing automotive industries were not applicable. They operated following the requirements from their motorcycle parent companies, which had gigantic markets, capabilities, and finance. Furthermore, the electric motorcycle industry was not yet ready because the R&D model seemed to be a push rather than pull market production employed by the existing industries. Therefore, a novel methodology and approaches for R&D and production are required. In terms of technology, business model, and company, this motorcycle was novel, meaning it was logical to implement the innovation-based approach to research, develop, and produce the GESITS. Lean start-up methodology governs the R&D process and was used to develop GESITS and its business model in less than two years. Subsequently, GESITS has been mass produced and sold in Indonesia and abroad with sales significantly increasing annually. Therefore, this article shows the successful implementation of the innovation-based concept in new industries—electrical motorcycles.
- 13 July 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1983 (1) , 050019
Properties of aluminum graphite composite prepared by stir casting
Aluminum graphite composite is one of the member of a new material called metal matrix composites (MMC). the MMC has paved its way in the field of automotive application due to its prospective properties. The purpose of the study is to investigate the effect of graphite reinforcement to the properties of the MMC, namely fluidity, hardness and impact energy. Aluminum – Silicon alloy is used as matrix metal, whereas graphite powder used as reinforcement in the amount of 1%, 2%, 4%, 6% and 8% respectively. Stir casting was used to prepare the composites at 850°C. Results indicate that the fluidity of aluminum graphite composite decreased as the amount of graphite is increase. Higher amount of graphite provides an increase of viscosity in the melts, thus decreasing the fluidity during casting. Hardness of the composite tends to be increasing with the increase of graphite amount, however the hardness starts to decline after the addition of 6 % graphite. The decreasing hardness is caused by the graphite powder clustering. Impact energy shows decreasing tendency as the amount of graphite becomes higher.
- 13 July 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1983 (1) , 050019
Properties of aluminum graphite composite prepared by stir casting
Aluminum graphite composite is one of the member of a new material called metal matrix composites (MMC). the MMC has paved its way in the field of automotive application due to its prospective properties. The purpose of the study is to investigate the effect of graphite reinforcement to the properties of the MMC, namely fluidity, hardness and impact energy. Aluminum – Silicon alloy is used as matrix metal, whereas graphite powder used as reinforcement in the amount of 1%, 2%, 4%, 6% and 8% respectively. Stir casting was used to prepare the composites at 850°C. Results indicate that the fluidity of aluminum graphite composite decreased as the amount of graphite is increase. Higher amount of graphite provides an increase of viscosity in the melts, thus decreasing the fluidity during casting. Hardness of the composite tends to be increasing with the increase of graphite amount, however the hardness starts to decline after the addition of 6 % graphite. The decreasing hardness is caused by the graphite powder clustering. Impact energy shows decreasing tendency as the amount of graphite becomes higher.