JLJianbin Luo

Jianbin Luo

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Jianbin Luo has a total of 12 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Enhanced Catalytic Soot Oxidation over Co-Based Metal Oxides: Effects of Transition Metal Doping

    by Jianbin Luo, Xinbo Zhu, Zhiwei Zhong, Geng Chen, Yu Hong, Zijian Zhou

    A series of Co-M (M = Fe, Cr, and Mn) catalysts were synthesized by the sol-gel method for soot oxidation in a loose contact mode. The Co-Fe catalyst exhibited the best catalytic activity among the tested samples, with the characteristic temperatures (T10, T50, and T90) of 470 °C, 557 °C, and 602 °C, respectively, which were 57 °C, 51 °C, and 51 °C lower than those of the CoOx catalyst. Catalyst characterizations of N2 adsorption–desorption, X-ray diffraction (XRD), X-ray photo-electron spectrometry (XPS), and the temperature programmed desorption of O2 (O2-TPD) were performed to gain insights into the relationships between the activity of catalytic soot oxidation and the catalyst properties. The content of Co2+ (68.6%) increased due to the interactions between Co and Fe, while the redox properties and the relative concentration of surface oxygen adsorption (51.7%) were all improved, which could significantly boost the activity of catalytic soot oxidation. The effects of NO and contact mode on soot oxidation were investigated over the Co-Fe catalyst. The addition of 1000 ppm of NO led to significant reductions in T10, T50, and T90 by 92 °C, 106 °C, and 104 °C, respectively, compared to the case without the NO addition. In the tight contact mode, the soot oxidation was accelerated over the Co-Fe catalyst, resulting in 46 °C, 50 °C, and 50 °C reductions in T10, T50, and T90 compared to the loose contact mode. The comparison between real soot and model Printex-U showed that the T50 value of real soot (455 °C) was 102 °C lower than the model Printex-U soot.


  • Open Access

    Soot Oxidation over γ-Al2O3-Supported Manganese-Based Binary Catalyst in a Dielectric Barrier Discharge Reactor

    by Xinbo Zhu, Xiqiang Wu, Jin Liu, Jianbin Luo, Zhengda Yang, Ye Jiang, Geng Chen

    In this work, soot oxidation was conducted over a series of Mn-X/γ-Al2O3 (M = Ce, Co and Cu) binary catalysts in a dielectric barrier discharge reactor. The soot conversion in the plasma–catalytic system was in the order of Mn/γ-Al2O3 (57.7%) > Mn-Co/γ-Al2O3 (53.9%) > Mn-Ce/γ-Al2O3 (51.6%) > Mn-Cu/γ-Al2O3 (47.7%) during the 30 min soot oxidation process at 14 W and 150 °C. Meanwhile, the doping of Ce, Co and Cu slightly improved the CO2 selectivity of the process by 4.7% to 10.3% compared to soot oxidation over Mn/γ-Al2O3.It is worth to note that the order of CO2 selectivity was in the opposite order with soot oxidation rate. The effects of discharge power, oxygen content in the carrier gas and reaction temperature on plasma–catalytic soot oxidation was systematically analyzed. The catalyst characterizations, including N2 adsorption–desorption, X-ray diffraction, X-ray photoelectron spectroscopy, temperature-programmed reduction by H2 and temperature-programmed desorption of O2, were conducted to illustrate the reaction mechanisms of plasma–catalytic soot oxidation and reaction pathways.


  • Open Access

    Soot Oxidation in a Plasma-Catalytic Reactor: A Case Study of Zeolite-Supported Vanadium Catalysts

    by Xinbo Zhu, Hanpeng Wu, Jianbin Luo, Jin Liu, Jiahao Yan, Zijian Zhou, Zhengda Yang, Ye Jiang, Geng Chen, Guohua Yang

    The plasma-catalytic oxidation of soot was studied over zeolite-supported vanadium catalysts, while four types of zeolites (MCM-41, mordenite, USY and 5A) were used as catalyst supports. The soot oxidation rate followed the order of V/MCM-41 > V/mordenite > V/USY > V/5A, while 100% soot oxidation was achieved at 54th min of reaction over V/MCM-41 and V/mordenite. The CO2 selectivity of the process follows the opposite order of oxidation rate over the V/M catalyst. A wide range of catalyst characterizations including N2 adsorption–desorption, XRD, XPS, H2-TPR and O2-TPD were performed to obtain insights regarding the reaction mechanisms of soot oxidation in plasma-catalytic systems. The redox properties were recognized to be crucial for the soot oxidation process. The effects of discharge power, gas flow rate and reaction temperature on soot oxidation were also investigated. The results showed that higher discharge power, higher gas flow rate and lower reaction temperature were beneficial for soot oxidation rate. However, these factors would impose a negative effect on CO2 selectivity. The proposed “plasma-catalysis” method possessed the unique advantages of quick response, mild operation conditions and system compactness. The method could be potentially applied for the regeneration of diesel particulate filters (DPF) at low temperatures and contribute to the the emission control of diesel engines.