Jin Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jin Liu has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Geng Chen
Faculty of Maritime and Transportation, Ningbo University, Ningbo 315211, China
2 shared publications - Jianbin Luo
Faculty of Maritime and Transportation, Ningbo University, Ningbo 315211, China
2 shared publications - Xinbo Zhu
Faculty of Maritime and Transportation, Ningbo University, Ningbo 315211, China
2 shared publications - Ye Jiang
College of New Energy, China University of Petroleum (East China), Qingdao 266580, China
2 shared publications - Zhengda Yang
College of New Energy, China University of Petroleum (East China), Qingdao 266580, China
2 shared publications - Guohua Yang
Faculty of Maritime and Transportation
1 shared publication
Latest Publications
- Open Access
Soot Oxidation over γ-Al2O3-Supported Manganese-Based Binary Catalyst in a Dielectric Barrier Discharge Reactor
In this work, soot oxidation was conducted over a series of Mn-X/γ-Al2O3 (M = Ce, Co and Cu) binary catalysts in a dielectric barrier discharge reactor. The soot conversion in the plasma–catalytic system was in the order of Mn/γ-Al2O3 (57.7%) > Mn-Co/γ-Al2O3 (53.9%) > Mn-Ce/γ-Al2O3 (51.6%) > Mn-Cu/γ-Al2O3 (47.7%) during the 30 min soot oxidation process at 14 W and 150 °C. Meanwhile, the doping of Ce, Co and Cu slightly improved the CO2 selectivity of the process by 4.7% to 10.3% compared to soot oxidation over Mn/γ-Al2O3.It is worth to note that the order of CO2 selectivity was in the opposite order with soot oxidation rate. The effects of discharge power, oxygen content in the carrier gas and reaction temperature on plasma–catalytic soot oxidation was systematically analyzed. The catalyst characterizations, including N2 adsorption–desorption, X-ray diffraction, X-ray photoelectron spectroscopy, temperature-programmed reduction by H2 and temperature-programmed desorption of O2, were conducted to illustrate the reaction mechanisms of plasma–catalytic soot oxidation and reaction pathways.
Open AccessSoot Oxidation over γ-Al2O3-Supported Manganese-Based Binary Catalyst in a Dielectric Barrier Discharge Reactor
In this work, soot oxidation was conducted over a series of Mn-X/γ-Al2O3 (M = Ce, Co and Cu) binary catalysts in a dielectric barrier discharge reactor. The soot conversion in the plasma–catalytic system was in the order of Mn/γ-Al2O3 (57.7%) > Mn-Co/γ-Al2O3 (53.9%) > Mn-Ce/γ-Al2O3 (51.6%) > Mn-Cu/γ-Al2O3 (47.7%) during the 30 min soot oxidation process at 14 W and 150 °C. Meanwhile, the doping of Ce, Co and Cu slightly improved the CO2 selectivity of the process by 4.7% to 10.3% compared to soot oxidation over Mn/γ-Al2O3.It is worth to note that the order of CO2 selectivity was in the opposite order with soot oxidation rate. The effects of discharge power, oxygen content in the carrier gas and reaction temperature on plasma–catalytic soot oxidation was systematically analyzed. The catalyst characterizations, including N2 adsorption–desorption, X-ray diffraction, X-ray photoelectron spectroscopy, temperature-programmed reduction by H2 and temperature-programmed desorption of O2, were conducted to illustrate the reaction mechanisms of plasma–catalytic soot oxidation and reaction pathways.
- Open Access
Soot Oxidation in a Plasma-Catalytic Reactor: A Case Study of Zeolite-Supported Vanadium Catalysts
The plasma-catalytic oxidation of soot was studied over zeolite-supported vanadium catalysts, while four types of zeolites (MCM-41, mordenite, USY and 5A) were used as catalyst supports. The soot oxidation rate followed the order of V/MCM-41 > V/mordenite > V/USY > V/5A, while 100% soot oxidation was achieved at 54th min of reaction over V/MCM-41 and V/mordenite. The CO2 selectivity of the process follows the opposite order of oxidation rate over the V/M catalyst. A wide range of catalyst characterizations including N2 adsorption–desorption, XRD, XPS, H2-TPR and O2-TPD were performed to obtain insights regarding the reaction mechanisms of soot oxidation in plasma-catalytic systems. The redox properties were recognized to be crucial for the soot oxidation process. The effects of discharge power, gas flow rate and reaction temperature on soot oxidation were also investigated. The results showed that higher discharge power, higher gas flow rate and lower reaction temperature were beneficial for soot oxidation rate. However, these factors would impose a negative effect on CO2 selectivity. The proposed “plasma-catalysis” method possessed the unique advantages of quick response, mild operation conditions and system compactness. The method could be potentially applied for the regeneration of diesel particulate filters (DPF) at low temperatures and contribute to the the emission control of diesel engines.
Open AccessSoot Oxidation in a Plasma-Catalytic Reactor: A Case Study of Zeolite-Supported Vanadium Catalysts
The plasma-catalytic oxidation of soot was studied over zeolite-supported vanadium catalysts, while four types of zeolites (MCM-41, mordenite, USY and 5A) were used as catalyst supports. The soot oxidation rate followed the order of V/MCM-41 > V/mordenite > V/USY > V/5A, while 100% soot oxidation was achieved at 54th min of reaction over V/MCM-41 and V/mordenite. The CO2 selectivity of the process follows the opposite order of oxidation rate over the V/M catalyst. A wide range of catalyst characterizations including N2 adsorption–desorption, XRD, XPS, H2-TPR and O2-TPD were performed to obtain insights regarding the reaction mechanisms of soot oxidation in plasma-catalytic systems. The redox properties were recognized to be crucial for the soot oxidation process. The effects of discharge power, gas flow rate and reaction temperature on soot oxidation were also investigated. The results showed that higher discharge power, higher gas flow rate and lower reaction temperature were beneficial for soot oxidation rate. However, these factors would impose a negative effect on CO2 selectivity. The proposed “plasma-catalysis” method possessed the unique advantages of quick response, mild operation conditions and system compactness. The method could be potentially applied for the regeneration of diesel particulate filters (DPF) at low temperatures and contribute to the the emission control of diesel engines.