Qiang Ma
Qiang Ma has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Fan Yang
College of Aeronautical Engineering, Civil Aviation University of China, Tianjin 300300, China
1 shared publication - Hao Wang
Tianjin Key Laboratory of High Speed Cutting and Precision Machining, Tianjin University of Technology and Education, Tianjin 300222, China
1 shared publication - Hao Wang
Tianjin Key Laboratory of High Speed Cutting and Precision Machining, Tianjin University of Technology and Education, Tianjin 300222, China
1 shared publication - Hongwei Zhang
Engineering Techniques Training Centre, Civil Aviation University of China, Tianjin 300300, China
1 shared publication - Huan Li
Tianjin Key Laboratory of Advanced Joining Technology, Tianjin University, Tianjin 300072, China
1 shared publication - Mingrui Zhang
Tianjin Key Laboratory of High Speed Cutting and Precision Machining, Tianjin University of Technology and Education, Tianjin 300222, China
1 shared publication
Latest Publications
- Open Access
Research on the Welding Process and Weld Formation in Multiple Solid-Flux Cored Wires Arc Hybrid Welding Process for Q960E Ultrahigh-Strength Steel
This paper proposes a novel welding process for ultrahigh-strength steel. The effects of welding parameters on the welding process and weld formation were studied to obtain the optimal parameter window. It was found that the metal transfer modes of solid wires were primarily determined by electrical parameters, while flux-cored wires consistently exhibited multiple droplets per pulse. The one droplet per pulse possessed better welding stability and weld formation, whereas the short-circuiting transfer or one droplet multiple pulses easily caused abnormal arc ignition that decreased welding stability, which could easily lead to a “sawtooth-shaped” weld formation or weld offset towards one side with more spatters. Thus, the electrical parameters corresponding to one droplet per pulse were identified as the optimal parameter window. Furthermore, the weld zone (WZ) was predominantly composed of AF, and the heat-affected zone (HAZ) primarily consisted of TM and LM. Consequently, the welded joint still exhibited excellent mechanical properties, particularly toughness, despite higher welding heat input. The average tensile strength reached 928 MPa, and the impact absorbed energy at −40 °C for the WZ and HAZ were 54 J and 126 J, respectively. In addition, the application of triple-wire welding for ultrahigh-strength steel (UHSS) demonstrated a significant enhancement in post-weld deposition rate, with increases of 106% and 38% compared to single-wire and twin-wire welding techniques, respectively. This process not only utilized flux-cored wire to enhance the mechanical properties of joints but also achieved high deposition rate welding.
Open AccessResearch on the Welding Process and Weld Formation in Multiple Solid-Flux Cored Wires Arc Hybrid Welding Process for Q960E Ultrahigh-Strength Steel
This paper proposes a novel welding process for ultrahigh-strength steel. The effects of welding parameters on the welding process and weld formation were studied to obtain the optimal parameter window. It was found that the metal transfer modes of solid wires were primarily determined by electrical parameters, while flux-cored wires consistently exhibited multiple droplets per pulse. The one droplet per pulse possessed better welding stability and weld formation, whereas the short-circuiting transfer or one droplet multiple pulses easily caused abnormal arc ignition that decreased welding stability, which could easily lead to a “sawtooth-shaped” weld formation or weld offset towards one side with more spatters. Thus, the electrical parameters corresponding to one droplet per pulse were identified as the optimal parameter window. Furthermore, the weld zone (WZ) was predominantly composed of AF, and the heat-affected zone (HAZ) primarily consisted of TM and LM. Consequently, the welded joint still exhibited excellent mechanical properties, particularly toughness, despite higher welding heat input. The average tensile strength reached 928 MPa, and the impact absorbed energy at −40 °C for the WZ and HAZ were 54 J and 126 J, respectively. In addition, the application of triple-wire welding for ultrahigh-strength steel (UHSS) demonstrated a significant enhancement in post-weld deposition rate, with increases of 106% and 38% compared to single-wire and twin-wire welding techniques, respectively. This process not only utilized flux-cored wire to enhance the mechanical properties of joints but also achieved high deposition rate welding.
- Open Access
Comparative Investigation on Wear Properties of Composite Coatings with Varying CeO2 Contents
Several innovative mixed powders of Ti6Al4V and NiCr-Cr3C2 with different CeO2 contents (0, 1, 2, 3, and 4 wt.%) were designed, and Ti2C-reinforced CrTi4-based composite coatings were prepared on the Ti6Al4V surface via laser cladding technology. The effects of CeO2 amount on the forming quality, microstructure, hardness, and wear resistance of the composite coatings were studied. The results showed that the CeO2 amount had a significant influence on the forming quality of the composite coatings. The cracks were eliminated completely when the CeO2 content was 2 wt.%; furthermore, the lowest porosity was obtained with the addition of 3 wt.% CeO2. The primary phase constituents of the coatings were non-stoichiometric Ti2C and a β-type solid solution (CrTi4) as the reinforcement and matrix, respectively. CeO2 and a low quantity of Ce2O3 were re-precipitated at the Ti2C/CrTi4 interface and CrTi4 grain boundary in the coatings with CeO2 addition. In addition, the average hardness of the composite coatings was 1.28–1.34 times higher than that of the Ti6Al4V substrate. The wear resistance of the composite coatings was significantly higher than that of the substrate. However, both the composite coatings and the Ti6Al4V substrate exhibited a mixed-wear mode, i.e., abrasive and adhesive wear.
Open AccessComparative Investigation on Wear Properties of Composite Coatings with Varying CeO2 Contents
Several innovative mixed powders of Ti6Al4V and NiCr-Cr3C2 with different CeO2 contents (0, 1, 2, 3, and 4 wt.%) were designed, and Ti2C-reinforced CrTi4-based composite coatings were prepared on the Ti6Al4V surface via laser cladding technology. The effects of CeO2 amount on the forming quality, microstructure, hardness, and wear resistance of the composite coatings were studied. The results showed that the CeO2 amount had a significant influence on the forming quality of the composite coatings. The cracks were eliminated completely when the CeO2 content was 2 wt.%; furthermore, the lowest porosity was obtained with the addition of 3 wt.% CeO2. The primary phase constituents of the coatings were non-stoichiometric Ti2C and a β-type solid solution (CrTi4) as the reinforcement and matrix, respectively. CeO2 and a low quantity of Ce2O3 were re-precipitated at the Ti2C/CrTi4 interface and CrTi4 grain boundary in the coatings with CeO2 addition. In addition, the average hardness of the composite coatings was 1.28–1.34 times higher than that of the Ti6Al4V substrate. The wear resistance of the composite coatings was significantly higher than that of the substrate. However, both the composite coatings and the Ti6Al4V substrate exhibited a mixed-wear mode, i.e., abrasive and adhesive wear.