Amanda S. Weerasooriya
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Amanda S. Weerasooriya has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
Andres A. Bujanda
Jefferson Davis Highway, Suite 1204, Arlington, VA 22202
1 shared publication- Andres Bujanda
DEVCOM Army Research Laboratory , Aberdeen Proving Ground, MD 21005
1 shared publication - Chi-Chin Wu
Weapons and Materials Research Directorate, US Army Combat Capabilities Development Command-Army Research Laboratory, Building 4600, Aberdeen Proving Ground, Maryland, 21005, UNITED STATES
1 shared publication - Daphne D. Pappas
Jefferson Davis Highway, Suite 1204, Arlington, VA 22202
1 shared publication - Eric Jason Robinette
Weapons and Materials Research Directorate, US Army Combat Capabilities Development Command Army Research Laboratory, Aberdeen Proving Ground, MD 21005, USA
1 shared publication Jacqueline Yim
Jefferson Davis Highway, Suite 1204, Arlington, VA 22202
1 shared publication
Latest Publications
- Open Access
Enhanced Interfacial Adhesion of Nylon 66 to Epoxy Resin EPON 825 by Non-thermal Atmospheric Pressure Dielectric Barrier Discharge Plasmas
Poly(hexamethylene adipamide), nylon 66, is a popular plastic that requires high surface wettability and strong adhesive bonds for many applications. However, pristine nylon is difficult to bond due to its hydrophobic nature and poor surface wettability. The objective of this work was to modify the physio-chemical surface properties of nylon 66 via a novel atmospheric plasma surface treatment approach using oxygen (O2) or water vapor (H2O) plasma glow. The surface hydrophilicity of the plasma-treated nylon surface was substantially enhanced immediately after either helium (He)/H2O or He/O2 plasma surface treatment. The average water contact angle was reduced from 65 degrees to ~30 degrees after He/H2O plasma and ~40 degrees after He/O2 plasma treatments. The improved hydrophilicity was also evidenced by the increased intensities of the surface oxygen and hydroxyl bonds in the X-ray photoelectron spectra. The interfacial adhesion strength of nylon surfaces before and after plasma treatment was further evaluated by uniaxial tensile tests of nylon single-joint lap shears bonded with three adhesives, i.e., thermoset epoxy resins EPON 825/ JEFFAMINE D-230 and EPON825/JEFFAMINE D-2000, and the thermoelastic polyurethane adhesive Sikaflex 252. The most significant improvements in bond strengths due to plasma treatment were found for lap shears bonded with the EPON 825/JEFFAMINE D-230 epoxy resin; their shear strengths with maximum loads were more than doubled—from 299–451 to 693–1594 N—after plasma treatment and were further enhanced by a factor of four to 895–1857 N after a subsequent silane treatment. In contrast, the bond strength of lap shears bonded with EPON 825/JEFFAMINE D-2000 and Sikaflex was not significantly improved because of the different a, re-affirming the importance of adhesive bulk properties This work presents the preliminary success of effective surface functionalization leading to enhanced interfacial adhesive bonds for nylon 66 via the development of scalable atmospheric plasma surface treatments.
Open AccessEnhanced Interfacial Adhesion of Nylon 66 to Epoxy Resin EPON 825 by Non-thermal Atmospheric Pressure Dielectric Barrier Discharge Plasmas
Poly(hexamethylene adipamide), nylon 66, is a popular plastic that requires high surface wettability and strong adhesive bonds for many applications. However, pristine nylon is difficult to bond due to its hydrophobic nature and poor surface wettability. The objective of this work was to modify the physio-chemical surface properties of nylon 66 via a novel atmospheric plasma surface treatment approach using oxygen (O2) or water vapor (H2O) plasma glow. The surface hydrophilicity of the plasma-treated nylon surface was substantially enhanced immediately after either helium (He)/H2O or He/O2 plasma surface treatment. The average water contact angle was reduced from 65 degrees to ~30 degrees after He/H2O plasma and ~40 degrees after He/O2 plasma treatments. The improved hydrophilicity was also evidenced by the increased intensities of the surface oxygen and hydroxyl bonds in the X-ray photoelectron spectra. The interfacial adhesion strength of nylon surfaces before and after plasma treatment was further evaluated by uniaxial tensile tests of nylon single-joint lap shears bonded with three adhesives, i.e., thermoset epoxy resins EPON 825/ JEFFAMINE D-230 and EPON825/JEFFAMINE D-2000, and the thermoelastic polyurethane adhesive Sikaflex 252. The most significant improvements in bond strengths due to plasma treatment were found for lap shears bonded with the EPON 825/JEFFAMINE D-230 epoxy resin; their shear strengths with maximum loads were more than doubled—from 299–451 to 693–1594 N—after plasma treatment and were further enhanced by a factor of four to 895–1857 N after a subsequent silane treatment. In contrast, the bond strength of lap shears bonded with EPON 825/JEFFAMINE D-2000 and Sikaflex was not significantly improved because of the different a, re-affirming the importance of adhesive bulk properties This work presents the preliminary success of effective surface functionalization leading to enhanced interfacial adhesive bonds for nylon 66 via the development of scalable atmospheric plasma surface treatments.
- Open Access
- 1 April 2014
- Published by Defense Technical Information Center (DTIC)
Development of Hydrophobic Coatings for Water-Repellent Surfaces Using Hybrid Methodology
Hydrophobic surfaces are of considerable interest due to their self-cleaning, wicking, water-repellent, and antimicrobial properties. Several approaches have been investigated for the development of hydrophobic and superhydrophobic materials. One in particular involves introducing surface roughness and chemical functionalities with hydrophobic end groups. In this work, hydrophobic surfaces were incorporated on ultra-high-molecular-weight polyethylene films using a three-step process. A treatment by plasma was employed before any other significant treatments to help with better adherence of particles acquired through silane wet chemistry, which was implemented to introduce surface roughness to yield a hierarchical assembly of silicon oxide (SiO2) nanoparticles. This was followed by plasma-enhanced chemical vapor deposition (PECVD) at atmospheric pressure to deposit a coating composed of fluorinated groups on the material. The chemical composition, wettability, and morphology of the surface were studied using water contact angle, Fourier transform infrared spectroscopy, x-ray photoelectron spectroscopy, atomic force microscopy, and scanning electron microscopy. Variations in the deposition processes of wet chemistry and PECVD were investigated. Fluorinated liquid precursors with different fluorocarbon structures and deposition time varied as well as the SiO2 nanoparticle loading. These parameters varied to obtain a surface with optimal distribution of particles coated with thin fluorocarbon films that exhibit hydrophobic behavior.
- 1 April 2014
- Published by Defense Technical Information Center (DTIC)
Open AccessDevelopment of Hydrophobic Coatings for Water-Repellent Surfaces Using Hybrid Methodology
Hydrophobic surfaces are of considerable interest due to their self-cleaning, wicking, water-repellent, and antimicrobial properties. Several approaches have been investigated for the development of hydrophobic and superhydrophobic materials. One in particular involves introducing surface roughness and chemical functionalities with hydrophobic end groups. In this work, hydrophobic surfaces were incorporated on ultra-high-molecular-weight polyethylene films using a three-step process. A treatment by plasma was employed before any other significant treatments to help with better adherence of particles acquired through silane wet chemistry, which was implemented to introduce surface roughness to yield a hierarchical assembly of silicon oxide (SiO2) nanoparticles. This was followed by plasma-enhanced chemical vapor deposition (PECVD) at atmospheric pressure to deposit a coating composed of fluorinated groups on the material. The chemical composition, wettability, and morphology of the surface were studied using water contact angle, Fourier transform infrared spectroscopy, x-ray photoelectron spectroscopy, atomic force microscopy, and scanning electron microscopy. Variations in the deposition processes of wet chemistry and PECVD were investigated. Fluorinated liquid precursors with different fluorocarbon structures and deposition time varied as well as the SiO2 nanoparticle loading. These parameters varied to obtain a surface with optimal distribution of particles coated with thin fluorocarbon films that exhibit hydrophobic behavior.