ABAndres Bujanda

Andres Bujanda

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Andres Bujanda has a total of 16 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Behavior of Polymeric Substrates and Sintered Silver Printed Hybrid Electronic Assemblies Subject to Extreme Acceleration Levels and Elevated Temperatures

    by Hayden Richards, Hisham Abusalma, Abhijit Dasgupta, Andres Bujanda, Harvey Tsang, Matthew Bowman

    This paper focuses on the response of printed hybrid electronic (PHE) assemblies with polymeric substrates and additively manufactured sintered silver electrical traces subject to extreme mechanical shocks (up to 100,000 g) and high temperatures (up to 150 °C). The substrates are hemispherical domes of injection-molded polycarbonate and polysulfone thermoplastics. Trace deposition onto the domes is accomplished by a novel process that combines conventional milling with extrusion printing to recess silver traces and dielectric insulation within the surface of the substrate. Mechanical shock testing is performed using an accelerated-fall drop tower equipped with a dual mass shock amplifier (DMSA) able to generate accelerations from 10,000 g up to 100,000 g with pulse durations of ∼0.05–0.1 ms and impact velocities of 6.5–20.5 m/s. Specimen performance is characterized by electrical and physical testing before and after testing. While polycarbonate domes survive multiple drops at all acceleration levels and temperatures, they are sensitive to heat and susceptible to warping and structural deformation at 150 °C which can compromise trace performance. Polysulfone domes can survive these temperatures without issue, but are less shock resistant and only survive 3–4 drops at 100,000 g (compared to 30+ for polycarbonate domes). Trace resistance is used as a metric to assess trace performance. All traces exhibit progressive long-term degradation over the course of multiple shocks, followed by instantaneous discontinuity during the final shock event. Trace failure (defined as the doubling of static trace resistance) occurs at ∼105–106 J/kg cumulative impact energy for all acceleration levels.


  • Extreme Drop Durability of Sintered Silver Traces Printed With Extrusion and Aerosol Jet Processes

    by Hisham Abusalma, Hayden Richards, Abhijit Dasgupta, Andres Bujanda, Harvey Tsang, Jian Yu

    Sintered silver is a popular material for printing conductive traces in printed hybrid electronics (PHE). However, due to the novel materials and printing techniques in PHEs, reliability still needs to be adequately characterized for all types of life-cycle application conditions. This paper focuses on characterizing the reliability of printed silver traces fabricated with extrusion printing and aerosol jet printing (AJP) processes, under severe shock conditions up to 40,000 g peak acceleration, resulting in very high strain magnitudes and strain rates. This study utilizes test specimens of cantilever form factor to study the reliability of three-dimensional printed traces and substrates. Traces printed using both techniques were found to withstand repetitive drops at up to 40,000 g peak acceleration. However, extrusion-printed silver traces were found to be more reliable than their AJP counterparts, because of the extruded traces' superior adhesion to the FR4 substrate and lack of sintering shrinkage cracks. Strain gauges revealed strains in excess of 10,000 με during a 40,000 g shock event. A calibrated finite element (FE) model revealed that the strains at the trace location exceeded 15,000 με during a 40,000 g shock event.


  • Open Access

    The Influence of Ink Chemistry on the Microstructure Evolution and GHz RF Response of Printed Ag Transmission Lines

    by Jason M. Summers, Shambhavi Sakri, Nishako Chakma, Hung Luyen, Andres Bujanda, Thomas Parker, Harvey Tsang, Nigel D. Shepherd

    High-frequency transmission is limited to the skin depth in metals. Because poor conductivity cannot be compensated for by increasing the conductor thickness as with DC, optimal transport properties are prerequisites for radio frequency (RF) use. Structural and chemical analyses of transmission lines printed using a traditional ink consisting of Ag nanoflakes in a dispersing phase revealed that optimized thermal treatments yielded thorough burnout of the binder, significant grain growth, elimination of the pore volume, and electrical responses that were comparable to values obtained for thermally evaporated, fully dense Ag controls. Specifically, a low DC resistivity of 2.3 μΩ·cm (1.4× bulk Ag) and RF transmission coefficients of 0.87 and 0.75 at 5 GHz and 10 GHz, respectively, were measured in the nanoflake Ag prints. Conversely, in transmission lines printed from a metal-organic decomposition ink, residual chemical contamination impeded diffusion and densification, yielding greater porosity, small grains that are pinned, and a degraded RF response. Reasonably good porosity approximations were obtained from a model based on percolation theory. The results indicate that contaminants at interfaces and pore surfaces impede diffusion, pore elimination, and full densification, and further, alter carrier dynamics and degrade RF response.


  • Open Access

    Enhanced Interfacial Adhesion of Nylon 66 to Epoxy Resin EPON 825 by Non-thermal Atmospheric Pressure Dielectric Barrier Discharge Plasmas

    by Chi-Chin Wu, John Derek Demaree, Amanda Weerasooriya, Andres Bujanda, Eric Jason Robinette

    Poly(hexamethylene adipamide), nylon 66, is a popular plastic that requires high surface wettability and strong adhesive bonds for many applications. However, pristine nylon is difficult to bond due to its hydrophobic nature and poor surface wettability. The objective of this work was to modify the physio-chemical surface properties of nylon 66 via a novel atmospheric plasma surface treatment approach using oxygen (O2) or water vapor (H2O) plasma glow. The surface hydrophilicity of the plasma-treated nylon surface was substantially enhanced immediately after either helium (He)/H2O or He/O2 plasma surface treatment. The average water contact angle was reduced from 65 degrees to ~30 degrees after He/H2O plasma and ~40 degrees after He/O2 plasma treatments. The improved hydrophilicity was also evidenced by the increased intensities of the surface oxygen and hydroxyl bonds in the X-ray photoelectron spectra. The interfacial adhesion strength of nylon surfaces before and after plasma treatment was further evaluated by uniaxial tensile tests of nylon single-joint lap shears bonded with three adhesives, i.e., thermoset epoxy resins EPON 825/ JEFFAMINE D-230 and EPON825/JEFFAMINE D-2000, and the thermoelastic polyurethane adhesive Sikaflex 252. The most significant improvements in bond strengths due to plasma treatment were found for lap shears bonded with the EPON 825/JEFFAMINE D-230 epoxy resin; their shear strengths with maximum loads were more than doubled—from 299–451 to 693–1594 N—after plasma treatment and were further enhanced by a factor of four to 895–1857 N after a subsequent silane treatment. In contrast, the bond strength of lap shears bonded with EPON 825/JEFFAMINE D-2000 and Sikaflex was not significantly improved because of the different a, re-affirming the importance of adhesive bulk properties This work presents the preliminary success of effective surface functionalization leading to enhanced interfacial adhesive bonds for nylon 66 via the development of scalable atmospheric plasma surface treatments.