Xinzhi Cao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Xinzhi Cao has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Anastasiia Konovalova
Technical University of Denmark
1 shared publication Matthias Breitwieser
Electrochemical Energy Systems, IMTEK, Department of Microsystems Engineering, University of Freiburg, Georges-Koehler-Allee 103, 79110 Freiburg, Germany
1 shared publication- Peter Mardle
Clean Energy Innovation Research Centre
1 shared publication - Philip Overton
Holdcroft Research Group, Department of Chemistry, Simon Fraser University, 8888 University Drive, Burnaby, BC V5A 1S6, Canada
1 shared publication Philipp Veh
Electrochemical Energy Systems, IMTEK, Department of Microsystems Engineering, University of Freiburg, Georges-Koehler-Allee 103, 79110 Freiburg, Germany
1 shared publication- Qiliang Wei
Institute of Micro/Nano Materials and Devices Ningbo University of Technology Ningbo China
1 shared publication
Latest Publications
- 8 June 2022
- Published by Royal Society of Chemistry (RSC) in Sustainable Energy & Fuels
- Vol. 6 (15) , 3551-3564
On the stability of anion exchange membrane fuel cells incorporating polyimidazolium ionene (Aemion+®) membranes and ionomers
We report the anion exchange membrane fuel cell (AEMFC) performance using commercial, polyimidazolium-based, Aemion+® as both the ionomer and membrane. Aemion+® affords reduced dimensional swelling yet higher water permeance compared to previously reported polybenzimidazolium-based Aemion® membranes and ionomers. Non-reinforced Aemion+® is shown to enhance the properties of Aemion® membranes, and Aemion+® reinforced with a fluorine-free polyolefin substrate is shown to enhance the properties considered important to fuel cell operation with respect to non-reinforced analogues. The highest AEMFC power density of 1.4 W cm−2 at 70 °C, 250 kPabs H2/O2 was obtained by using a direct membrane deposition (DMD) approach, where an ultrathin 5 μm membrane increased the voltage stability through enhanced water permeation, allowing characterization under these conditions. However, the reinforcement was found to be pivotal in enabling stable AEMFC operation at 80 °C, where a 10 μm-thick reinforced Aemion+® provided 1.1 W cm−2 power at 80 °C, 300 kPaabs H2/O2. The degradation properties of this material under varied cell temperatures, current densities and RHs are finally examined.
- 8 June 2022
- Published by Royal Society of Chemistry (RSC) in Sustainable Energy & Fuels
- Vol. 6 (15) , 3551-3564
On the stability of anion exchange membrane fuel cells incorporating polyimidazolium ionene (Aemion+®) membranes and ionomers
We report the anion exchange membrane fuel cell (AEMFC) performance using commercial, polyimidazolium-based, Aemion+® as both the ionomer and membrane. Aemion+® affords reduced dimensional swelling yet higher water permeance compared to previously reported polybenzimidazolium-based Aemion® membranes and ionomers. Non-reinforced Aemion+® is shown to enhance the properties of Aemion® membranes, and Aemion+® reinforced with a fluorine-free polyolefin substrate is shown to enhance the properties considered important to fuel cell operation with respect to non-reinforced analogues. The highest AEMFC power density of 1.4 W cm−2 at 70 °C, 250 kPabs H2/O2 was obtained by using a direct membrane deposition (DMD) approach, where an ultrathin 5 μm membrane increased the voltage stability through enhanced water permeation, allowing characterization under these conditions. However, the reinforcement was found to be pivotal in enabling stable AEMFC operation at 80 °C, where a 10 μm-thick reinforced Aemion+® provided 1.1 W cm−2 power at 80 °C, 300 kPaabs H2/O2. The degradation properties of this material under varied cell temperatures, current densities and RHs are finally examined.