Jesus Alfonso
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jesus Alfonso has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
J. Orus
SISTRONIC group, Instituto Tecnológico de Aragón, Zaragoza, Spain
4 shared publicationsF. Rotella
ENIT, Tarbes, France
2 shared publicationsJ. M. Rodriguez-Fortun
SISTRONIC group, Instituto Tecnológico de Aragón, Zaragoza, Spain
2 shared publicationsJ.M. Rodriguez-Fortun
Grupo de Investigación Aplicada (GIA-MDPI), Instituto Tecnológico de Aragón, Zaragoza, Spain
2 shared publicationsJose A. Castellanos
Instituto de Ingeniería de Aragón, Universidad de Zaragoza, Zaragoza, Spain
2 shared publications- Jose Angel Castellanos
Instituto de Investigacin en Ingeniera de Aragn (I3A), Universidad de Zaragoza, Zaragoza, Spain
2 shared publications
Latest Publications
- Open Access
- 9 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Vehicular Technology
- Vol. 6, 1661-1672
Geographically Distributed Test Environment: Validation of Integrated Motion Control of Multi-Actuated Electric Vehicle
As an example of a geographically distributed test environment, an integrated motion control system for multi-actuated electric vehicles has been proposed and evaluated. This system unifies three active subsystems: drive-by-wire propulsion with independent in-wheel electric motors, electro-hydraulic brake actuators, and active suspension actuators. A distributed X-in-the-loop network architecture supports the approach, integrating a real-time validated vehicle model, dedicated test benches for each subsystem, and a driving simulator located in different geographical locations. This setup enables real-time testing and validation of the integrated control strategy. Validation results show improved ride comfort and safety.
- 9 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Vehicular Technology
- Vol. 6, 1661-1672
Open AccessGeographically Distributed Test Environment: Validation of Integrated Motion Control of Multi-Actuated Electric Vehicle
As an example of a geographically distributed test environment, an integrated motion control system for multi-actuated electric vehicles has been proposed and evaluated. This system unifies three active subsystems: drive-by-wire propulsion with independent in-wheel electric motors, electro-hydraulic brake actuators, and active suspension actuators. A distributed X-in-the-loop network architecture supports the approach, integrating a real-time validated vehicle model, dedicated test benches for each subsystem, and a driving simulator located in different geographical locations. This setup enables real-time testing and validation of the integrated control strategy. Validation results show improved ride comfort and safety.
- 17 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 1, 1002-1007
Geographically distributed real-time co-simulation of electric vehicle
The present paper shows the capabilities of a distributed real-time co-simulation environment merging simulation models and testing facilities for developing and verifying electric vehicles. This environment has been developed in the framework of the XILforEV project and the presented case is focused on a ride control with a real suspension installed on a test bench in Spain, which uses real-time information from a complete vehicle model in Germany. Given the long distance between both sites, it has been necessary to develop a specific delay compensation algorithm. This algorithm is general enough to be used in other real-time co-simulation frameworks. In the present work, the system architecture including the communication compensation is described and successfully experimentally validated.
- 17 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 1, 1002-1007
Geographically distributed real-time co-simulation of electric vehicle
The present paper shows the capabilities of a distributed real-time co-simulation environment merging simulation models and testing facilities for developing and verifying electric vehicles. This environment has been developed in the framework of the XILforEV project and the presented case is focused on a ride control with a real suspension installed on a test bench in Spain, which uses real-time information from a complete vehicle model in Germany. Given the long distance between both sites, it has been necessary to develop a specific delay compensation algorithm. This algorithm is general enough to be used in other real-time co-simulation frameworks. In the present work, the system architecture including the communication compensation is described and successfully experimentally validated.
- 1 July 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 703-708
Iterative learning control of a long range tribometer under repetitive perturbation and friction
The present paper proposes an iterative learning control (ILC) algorithm for accurate force tracking in a long range tribometer. The device is a nonlinear single input single output plant affected by repetitive and non repetitive perturbations in the output. The former perturbations result from the repetitive nature of the tests, and the latter ones are caused by friction phenomena in the guiding elements. Due to the characteristics of the device, it has been necessary to develop specific solutions to assure a robust behavior: on the one hand, analysis and identification techniques for the perturbations, and on the other hand, a spatial synchronization. The finally developed controller combines ILC with feedforward and feedback commands. The system is experimentally validated and the results show a substantial improvement in the performance compared to more classical approaches.
- 1 July 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 703-708
Iterative learning control of a long range tribometer under repetitive perturbation and friction
The present paper proposes an iterative learning control (ILC) algorithm for accurate force tracking in a long range tribometer. The device is a nonlinear single input single output plant affected by repetitive and non repetitive perturbations in the output. The former perturbations result from the repetitive nature of the tests, and the latter ones are caused by friction phenomena in the guiding elements. Due to the characteristics of the device, it has been necessary to develop specific solutions to assure a robust behavior: on the one hand, analysis and identification techniques for the perturbations, and on the other hand, a spatial synchronization. The finally developed controller combines ILC with feedforward and feedback commands. The system is experimentally validated and the results show a substantial improvement in the performance compared to more classical approaches.
- 1 December 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 01912216,p. 342-347
Model-free control of a 3-DOF piezoelectric nanopositioning platform
A model-free controller is designed for a nanopositioning platform with three degrees of freedom. The system is specially difficult to control because of the coupling between the different movements and the hysteresis present in the piezoelectric actuators. The authors propose a control design methodology based on the so called ultra-local system description. The developed controller has been implemented and validated on a real test bench and it has proven a good performance in handling the nonlinearities and uncertainties present in the platform.
- 1 December 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 01912216,p. 342-347
Model-free control of a 3-DOF piezoelectric nanopositioning platform
A model-free controller is designed for a nanopositioning platform with three degrees of freedom. The system is specially difficult to control because of the coupling between the different movements and the hysteresis present in the piezoelectric actuators. The authors propose a control design methodology based on the so called ultra-local system description. The developed controller has been implemented and validated on a real test bench and it has proven a good performance in handling the nonlinearities and uncertainties present in the platform.
- 1 December 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 01912216,p. 1633-1638
Control of a multi-axis platform for metrological purposes using differential flatness
Positioning and tracking devices with micrometer range and sub-micrometer resolution are becoming of special interest in recent years for an extending range of applications including metrological devices, manipulators and mechanization systems both in research and high precision industries (for example, semiconductors). The control of these systems is not an easy task because of its normally high stiffness and the coupling existing between the different degrees of freedom. The present work proposes a control strategy based on differential flatness for static positioning and dynamic trajectory tracking with a platform of three degrees of freedom. The system uses piezoelectric actuators and is specially conceived for metrological devices, which do not suffer important external loads. The proposed method permits to decouple the design of a closed loop control for each degree of freedom and calculates an open loop command directly from the trajectory definition in the three degrees of freedom. The performance of the controller has been experimentally checked both in positioning and tracking applications.
- 1 December 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 01912216,p. 1633-1638
Control of a multi-axis platform for metrological purposes using differential flatness
Positioning and tracking devices with micrometer range and sub-micrometer resolution are becoming of special interest in recent years for an extending range of applications including metrological devices, manipulators and mechanization systems both in research and high precision industries (for example, semiconductors). The control of these systems is not an easy task because of its normally high stiffness and the coupling existing between the different degrees of freedom. The present work proposes a control strategy based on differential flatness for static positioning and dynamic trajectory tracking with a platform of three degrees of freedom. The system uses piezoelectric actuators and is specially conceived for metrological devices, which do not suffer important external loads. The proposed method permits to decouple the design of a closed loop control for each degree of freedom and calculates an open loop command directly from the trajectory definition in the three degrees of freedom. The performance of the controller has been experimentally checked both in positioning and tracking applications.
- 29 September 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE/ASME Transactions on Mechatronics
- Vol. 18 (1) , 221-229
Flatness-Based Active Vibration Control for Piezoelectric Actuators
The accuracy and resolution of metrological devices (coordinate measuring machines -CMM-, interferometers, etc.) are greatly affected by their robustness to external vibrations. This is especially important in the case of micrometric and nanometric microscopes, such as atomic force microscopes (AFM). In such cases, active vibration control strategies are frequently used, requiring actuators capable of fast and accurate responses. Piezoelectric actuators meet these requirements but they suffer from two major drawbacks, hysteresis, and rate dependence, which must be taken into consideration in the design of the control strategy. The present work proposes a novel active vibration control strategy using piezoelectric actuators for metrological devices affected by low external loads. The control strategy combines a classical sky-hook feedback with a feedforward control. The effect of hysteresis is minimized by compensating the senstivity variations of the actuator in oscillatory movements. For the design of the feedforward law, the present work demonstrates that a stack piezoelectric actuator working as a damper admits a mathematical description fulfilling differential flatness. It also proposes a formulation of the active vibration damping problem in terms of a trajectory tracking command perfectly fitted to the flatness-based control law. This strategy obtains damping improvements in the entire frequency range of operation without the instability problems derived from high feedback gains.
- 29 September 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE/ASME Transactions on Mechatronics
- Vol. 18 (1) , 221-229
Flatness-Based Active Vibration Control for Piezoelectric Actuators
The accuracy and resolution of metrological devices (coordinate measuring machines -CMM-, interferometers, etc.) are greatly affected by their robustness to external vibrations. This is especially important in the case of micrometric and nanometric microscopes, such as atomic force microscopes (AFM). In such cases, active vibration control strategies are frequently used, requiring actuators capable of fast and accurate responses. Piezoelectric actuators meet these requirements but they suffer from two major drawbacks, hysteresis, and rate dependence, which must be taken into consideration in the design of the control strategy. The present work proposes a novel active vibration control strategy using piezoelectric actuators for metrological devices affected by low external loads. The control strategy combines a classical sky-hook feedback with a feedforward control. The effect of hysteresis is minimized by compensating the senstivity variations of the actuator in oscillatory movements. For the design of the feedforward law, the present work demonstrates that a stack piezoelectric actuator working as a damper admits a mathematical description fulfilling differential flatness. It also proposes a formulation of the active vibration damping problem in terms of a trajectory tracking command perfectly fitted to the flatness-based control law. This strategy obtains damping improvements in the entire frequency range of operation without the instability problems derived from high feedback gains.
- 1 January 2011
- Published by Elsevier in IFAC Proceedings Volumes
- Vol. 44 (1) , 5237-5242
Hysteresis in Piezoelectric Actuators: Modeling and Compensation
- 1 January 2011
- Published by Elsevier in IFAC Proceedings Volumes
- Vol. 44 (1) , 5237-5242
Hysteresis in Piezoelectric Actuators: Modeling and Compensation
- 1 June 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 744-749
Nonlinear active vibration control using piezoelectric actuators
The ever increasing resolution of metrological and production devices, with required operation ranges below one micron, results in the necessity for isolating the sensor or tool from any external perturbation. For that, it is normally unavoidable the application of active strategies, capable of eliminating the resonance peaks and obtaining good damping results without an important reduction in the stiffness of the system, as it would happen if passive strategies were adopted. Too low stiffness of the system would result in accuracy losses due to large displacements of the device under external perturbations. For the active vibration control strategies at so low displacement ranges, the piezoelectric actuators represent a good option due to both their high movement accuracy and stiffness. Nevertheless, the nonlinear behaviour of these actuators negatively affects the final efficiency of the control strategy if that characteristic is not taken into account. This work proposes a compensator of the nonlinear effects accompanying a vibration control strategy based on the sky-hook control law. The parameters for the compensator can be estimated either off-line or on-line, and in both cases, experimental results show an important improvement with respect to traditional approaches.
- 1 June 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 744-749
Nonlinear active vibration control using piezoelectric actuators
The ever increasing resolution of metrological and production devices, with required operation ranges below one micron, results in the necessity for isolating the sensor or tool from any external perturbation. For that, it is normally unavoidable the application of active strategies, capable of eliminating the resonance peaks and obtaining good damping results without an important reduction in the stiffness of the system, as it would happen if passive strategies were adopted. Too low stiffness of the system would result in accuracy losses due to large displacements of the device under external perturbations. For the active vibration control strategies at so low displacement ranges, the piezoelectric actuators represent a good option due to both their high movement accuracy and stiffness. Nevertheless, the nonlinear behaviour of these actuators negatively affects the final efficiency of the control strategy if that characteristic is not taken into account. This work proposes a compensator of the nonlinear effects accompanying a vibration control strategy based on the sky-hook control law. The parameters for the compensator can be estimated either off-line or on-line, and in both cases, experimental results show an important improvement with respect to traditional approaches.