GIGulnaz Ibraimbayeva

Gulnaz Ibraimbayeva

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Gulnaz Ibraimbayeva has a total of 26 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • THE USE OF MINERAL RAW MATERIALS OF ZHAMBYL REGION IN THE PRODUCTION OF BUILDING CERAMICS

    by G.B. Ibraimbayeva, M.S. Bakyt, A.A. Guvalov, V.T. Stanevich

    The utilization of clay raw materials in combination with industrial by-products, such as phosphorus slag and waste glass, offers an effective approach to expanding the raw material base of ceramic production, reducing environmental impacts, and improving the efficiency of natural resource utilization. This study evaluates the feasibility of using medium-plastic loam from the Sarykemer deposit, granulated phosphorus slag, and ground waste glass in the production of building ceramics and determines the optimal ceramic mass composition to achieve enhanced physical and mechanical properties. The chemical and mineralogical compositions of the raw materials and their influence on the properties of the ceramic body were investigated. Experimental specimens with different component proportions were prepared at a molding moisture content of 20%, followed by drying and firing at temperatures ranging from 900 to 1050 °C. The optimum firing temperature was determined based on the degree of sintering observed on the fracture surface and the physical and mechanical properties of the fired specimens. The optimal ceramic composition was found to consist of 80% loam, 15% phosphorus slag, and 5% ground waste glass. The incorporation of these additives enhanced the sintering process, promoted the formation of a dense ceramic body, and improved the physical and mechanical properties of the material. Specimens fired at the optimum temperature of 1000 °C exhibited a compressive strength of at least 20 MPa. The obtained results demonstrate the effectiveness of utilizing local mineral resources and industrial by-products from the Zhambyl region for the production of wall ceramics, enabling the manufacture of high-quality ceramic materials with improved performance, reduced consumption of natural raw materials, and enhanced environmental sustainability of the production process.

  • Open Access

    Application of Feldspar Sand in Non-Autoclaved Foam Concrete Technology

    by Mederbay Saduakassov, Vladimir Lapin, Bakhadyr Kopzhassarov, Georgiy Tokmadzheshvili, Erlan Кushekov, Gulnaz Ibraimbayeva

    The aim of this study is to determine the possibility of producing non-autoclaved foam concrete of grade M35 with a density of 900 kg/m³. A distinctive feature of this development is the testing of twin samples from the same batch: some were steamed in a chamber at 90 °C under normal atmospheric pressure, while others were autoclaved at a pressure of 8 bar and a temperature of 170 °C. It was established that ordinary natural feldspar sands with a fineness modulus ranging from 1.43 to 2.45, containing quartz below the standard-regulated levels, can be used in the production of non-autoclaved foam concrete. It is not possible to obtain non-autoclaved D900 foam concrete of grade M35 strength using only cement, sand, and foaming agent. To achieve the specified strength, it is necessary to use coarse sand with a fineness modulus (FM) greater than 3, subjected to short-term grinding to reduce the FM to recommended values, and to additionally introduce sol-gel liquid glass. The novelty lies in the experimental confirmation of the features of strength formation in cellular concrete under both non-autoclaved and autoclaved curing conditions. Comparative tests showed that high strength in cellular concrete is achieved only when a chemical bond forms between the products of cement hydrolysis and hydration with quartz sand grains—conditions made possible through autoclaving.


  • RESEARCH OF THE POSSIBILITY OF USING CHP ASH IN THE PRODUCTION OF FIRED ASH GRAVEL

    by Korkyt Ata Kyzylorda University, А. Khamit, S. Uderbaev, K. Baitassov, Kyzylorda «Bolashak» University, G. Ibraimbaeva, International Educational Corporation, S. Kultayeva

    The article presents a comparative analysis of the characteristics of the dump ash of the Kyzylorda CHP hydraulic removal. A huge amount of ash, slag waste is collected in the dumps of the CHP, their accumulation in the dumps leads to a violation of the ecology of the environment. The issue of ash, slag waste disposal is an urgent problem. The use of ash and slag not only solves the issue of availability of raw materials, but also allows to improve the quality of products while reducing their cost. One of the valuable components of ash and slag waste is hydraulic removal ash. Hydraulic removal ash as a raw material can be used for the manufacture of artificial concrete aggregates (ash, agglomerate gravel, etc.). Studies were conducted to study the physico-chemical composition, determine the specific effective activity of natural radionuclides, loss during calcination of two types of hydraulic removal ash samples from Kyzylorda CHP (black and gray), which differ in sampling sites from ash dump. When studying the properties of the ash, X-Ray phase analysis was carried out, with the help of which the phase composition of the ash was determined. Work was carried out on the X-Ray phase analysis of ash, determination of the specific effective activity of natural radionuclides, calcination losses, which showed the possibility of using ash for the production of building materials. The conducted studies have confirmed the expediency of using the ash of the Kyzylorda thermal power plant in the production of fired ash gravel.


  • Open Access

    THERMAL INSULATION PERLITE CONCRETE GRADES D150 and D200

    by International Educational Corporation, G.B. Ibraimbayeva, M.S. Saduakasov, Almaty Beton Materialdary Llp, M.A. Ermukhanbet, Satbayev University, T.B. Meyrkhanov, Nazarbayev University, A.M. Shoibekova

    The article presents the results of research on the development of compositions and the study of the physico-mechanical properties of particularly light perlite concrete. It has been found that the use of foam makes it possible to dramatically increase the volume of cement dough, which makes it possible to mix the solution with brittle, weakly strong grains of expanded perlite sand. As a result of experimental studies, perlite concrete was obtained with an average dry density of 150-200 kg/m3, compressive strength of 0.32-0.43 MPa, thermal conductivity coefficient of 0.048-0.052 W / (m · ° C). The plates are designed for thermal insulation of residential and public buildings. In the conditions of Almaty, with a plate thickness of 10 cm, the required thermal protection of external structures of buildings is provided.

  • Open Access

    THE EFFECT OF MODIFYING ADDITIVES ON THE PROPERTIES OF THE CERAMIC COMPOSITION

    by International Educational Corporation, G.B. Ibraimbayeva, G.K. Abildaeva, Almaty «KazSertik-A» LLP, S.A. Shirakhanov, A.M. Sagindykova

    The results of studies of the effect of modifying additives on the properties of ceramic masses are presented. It is shown that the complex activation of the ceramic mass by plasticizing additives in the form of bentonite and surfactants and using rice straw leads to a decrease in molding humidity and an improvement in the physical and mechanical properties of ceramics while reducing the firing temperature by 50-100 °C. The optimal composition of a ceramic composition containing low-plastic loam, bentonite, rice straw and surfactants for the production of ceramic bricks by plastic molding has been determined.

  • INVESTIGATION OF THE INFLUENCE OF ADDITIVES-REGULATORS ON THE PROPERTIES OF BUILDING CERAMICS

    by G.K. Abildaeva, G.B. Ibraimbayeva, S.Kh. Seydakhmetov

    The results of the study of the influence of various additives on the properties of ceramic masses in order to improve the physical and mechanical wall products and ensure re-source-saving technology of their production are presented. The effect of surfactants of various na-ture, thermal power plant ash and rice straw on the formation of the properties of ceramic samples was studied.