Ahmad Al-Hosainat
Research Subjects
Ahmad Al-Hosainat has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Munir D. Nazzal
University of Cincinnati
3 shared publications - Savas Kaya
School of Electrical Engineering and Computer Science, Ohio University, Athens, OH, USA
2 shared publications Ala Abbas
Department of Civil Engineering, University of Akron, Akron, OH
1 shared publication- Ala R. Abbas
Department of Civil Engineering, The University of Akron, Akron, OH
1 shared publication Eric Biehl
Ohio Department of Transportation, Office of Materials Management, Columbus, OH
1 shared publicationLana Abu Qtaish
Geotechnical Engineer, Mannik & Smith Group, Detroit, MI 48226
1 shared publication
Latest Publications
- Open Access
Nano-Scale and Macro-Scale Characterizations of the Effects of Recycled Plastics on Asphalt Binder Properties
This paper summarizes the results of one of the first comprehensive laboratory studies that was conducted to evaluate the effects of adding different contents of recycled polyethylene terephthalate (rPETE) as a modifier to an asphalt binder on the rheological and mechanical properties of the modified binder as well as on the agglomeration behavior between the rPETE and asphalt binder at a multiscale level. The high-temperature and low-temperature performances of the modified binder were investigated at the macro-scale and compared with those of the unmodified binder using dynamic shear rheometer (DSR) and bending-beam rheometer (BBR) rheological tests, as well as asphalt binder cracking device (ABCD) testing. The nano-scale evaluation of the binder properties, including the surface roughness, bonding energy, and reduced modulus, was accomplished using atomic force microscopy (AFM). The results indicated that the addition of rPETE enhanced the high- and intermediate-temperature rheological properties of the modified PG 64-22 binder. The low-temperature rheological properties and resistance to cracking decreased slightly with increasing rPETE content in the asphalt binder. However, this reduction was not remarkable when adding 4%, 8%, and 10% rPETE contents. The asphalt binder modified with 4% rPETE had a low-temperature grade of −22, similar to that of the unmodified binder, indicating that 4% rPETE can be added to the binder to improve its high- and intermediate-temperature properties without reducing its resistance to low-temperature damage. The AFM tapping-mode results indicated that the inclusion of rPETE in the asphalt binder improved the stiffness properties of the modified binder as compared with those of the control asphalt binder. In addition, the rPETE-modified binders showed rougher surfaces than the control binder. The addition of rPETE to the binder increased the values of the reduced modulus and bonding energy compared with those of the control binder.
Open AccessNano-Scale and Macro-Scale Characterizations of the Effects of Recycled Plastics on Asphalt Binder Properties
This paper summarizes the results of one of the first comprehensive laboratory studies that was conducted to evaluate the effects of adding different contents of recycled polyethylene terephthalate (rPETE) as a modifier to an asphalt binder on the rheological and mechanical properties of the modified binder as well as on the agglomeration behavior between the rPETE and asphalt binder at a multiscale level. The high-temperature and low-temperature performances of the modified binder were investigated at the macro-scale and compared with those of the unmodified binder using dynamic shear rheometer (DSR) and bending-beam rheometer (BBR) rheological tests, as well as asphalt binder cracking device (ABCD) testing. The nano-scale evaluation of the binder properties, including the surface roughness, bonding energy, and reduced modulus, was accomplished using atomic force microscopy (AFM). The results indicated that the addition of rPETE enhanced the high- and intermediate-temperature rheological properties of the modified PG 64-22 binder. The low-temperature rheological properties and resistance to cracking decreased slightly with increasing rPETE content in the asphalt binder. However, this reduction was not remarkable when adding 4%, 8%, and 10% rPETE contents. The asphalt binder modified with 4% rPETE had a low-temperature grade of −22, similar to that of the unmodified binder, indicating that 4% rPETE can be added to the binder to improve its high- and intermediate-temperature properties without reducing its resistance to low-temperature damage. The AFM tapping-mode results indicated that the inclusion of rPETE in the asphalt binder improved the stiffness properties of the modified binder as compared with those of the control asphalt binder. In addition, the rPETE-modified binders showed rougher surfaces than the control binder. The addition of rPETE to the binder increased the values of the reduced modulus and bonding energy compared with those of the control binder.
- 2 July 2022
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2676 (11) , 596-608
Evaluation of the Interlayer Bond Strength of Micro-Surfacing Mixes
This paper presents the results of the first study to evaluate the effects of the tack coat and micro-surfacing mix properties on the interlayer bond strength between the micro-surfacing layer(s) and existing pavement surface. Several factors were investigated, which included the type of tack coat material, tack coat application rate, and the residual binder content of the micro-surfacing mix. To this end, a total of 14 field micro-surfacing test sections were installed on Ohio State Route 03 in Wayne County, Ohio. While the first seven sections were constructed with a single micro-surfacing layer, the other seven sections had double micro-surfacing layers. Five tack coat application rates and two residual binder contents were evaluated. The testing plan involved obtaining core samples from the constructed sections 1 week, 4 months, and 12 months after construction. The obtained field cores were tested in the laboratory using two types of pull-off tests and a torque bond strength test. The results of bond strength tests on obtained field cores and the statistical analysis performed on these results indicated that sections with no tack coat had significantly lower bond strength than those with tack coat with at least 0.05 gallons per square yard (gsy) total application (0.0083 gsy residual application rate). Furthermore, results indicated that the use of 0.75% lower residual asphalt binder content in micro-surfacing mixes resulted in significantly lower bond strength between the micro-surfacing and existing pavement. The tack coat material properties had some effect on the interlayer bond strength; however, this effect was statistically insignificant.
- 2 July 2022
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2676 (11) , 596-608
Evaluation of the Interlayer Bond Strength of Micro-Surfacing Mixes
This paper presents the results of the first study to evaluate the effects of the tack coat and micro-surfacing mix properties on the interlayer bond strength between the micro-surfacing layer(s) and existing pavement surface. Several factors were investigated, which included the type of tack coat material, tack coat application rate, and the residual binder content of the micro-surfacing mix. To this end, a total of 14 field micro-surfacing test sections were installed on Ohio State Route 03 in Wayne County, Ohio. While the first seven sections were constructed with a single micro-surfacing layer, the other seven sections had double micro-surfacing layers. Five tack coat application rates and two residual binder contents were evaluated. The testing plan involved obtaining core samples from the constructed sections 1 week, 4 months, and 12 months after construction. The obtained field cores were tested in the laboratory using two types of pull-off tests and a torque bond strength test. The results of bond strength tests on obtained field cores and the statistical analysis performed on these results indicated that sections with no tack coat had significantly lower bond strength than those with tack coat with at least 0.05 gallons per square yard (gsy) total application (0.0083 gsy residual application rate). Furthermore, results indicated that the use of 0.75% lower residual asphalt binder content in micro-surfacing mixes resulted in significantly lower bond strength between the micro-surfacing and existing pavement. The tack coat material properties had some effect on the interlayer bond strength; however, this effect was statistically insignificant.
- 1 December 2021
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 33 (12) , 04021369
Evaluation of Moisture Damage in Asphalt Mixtures at Macro- and Nanoscales
The aim of this study was to examine the effects of different additives on the moisture resistance of asphalt binders using atomic force microscopy (AFM), and to correlate the results with those obtained in macroscale tests. To this end, AFM force spectroscopy was conducted on neat and polymer-modified asphalt binders produced using various warm mix asphalt (WMA) technologies. The technologies considered included Sasobit, Advera, foamed WMA, and Evotherm M1. Furthermore, the asphalt mixtures were prepared using the considered asphalt binders and were tested using the AASHTO T 283 test. The results of this study show that the most significant factor affecting the AFM adhesive forces of asphalt binders is the use of polymer additives. However, the interactions between various chemical groups in asphalt binders and the considered additives differ. Finally, it was found that the effect of aggregate-binder adhesive bonds on indirect tensile strength is greater than that of the binder’s cohesive bonds, as the cracking in this AASHTO T 283 test has more tendency to occur at the interface between the aggregate and the binder due to the high stress concentration.
- 1 December 2021
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 33 (12) , 04021369
Evaluation of Moisture Damage in Asphalt Mixtures at Macro- and Nanoscales
The aim of this study was to examine the effects of different additives on the moisture resistance of asphalt binders using atomic force microscopy (AFM), and to correlate the results with those obtained in macroscale tests. To this end, AFM force spectroscopy was conducted on neat and polymer-modified asphalt binders produced using various warm mix asphalt (WMA) technologies. The technologies considered included Sasobit, Advera, foamed WMA, and Evotherm M1. Furthermore, the asphalt mixtures were prepared using the considered asphalt binders and were tested using the AASHTO T 283 test. The results of this study show that the most significant factor affecting the AFM adhesive forces of asphalt binders is the use of polymer additives. However, the interactions between various chemical groups in asphalt binders and the considered additives differ. Finally, it was found that the effect of aggregate-binder adhesive bonds on indirect tensile strength is greater than that of the binder’s cohesive bonds, as the cracking in this AASHTO T 283 test has more tendency to occur at the interface between the aggregate and the binder due to the high stress concentration.