AAAla R. Abbas

Ala R. Abbas

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ala R. Abbas has a total of 11 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Characterization of Aggregate Susceptibility to Polishing Using the Micro-Deval Test

    by Khalil Alafeef, Tariq Sharaf, Ala R. Abbas

    Skid resistance is a critical pavement surface property affecting roadway safety, especially under wet weather conditions. This study evaluated the frictional characteristics of a wide variety of aggregates used in roadway construction in Ohio. The micro-Deval test was used to apply different levels of polishing (0, 60, 180, and 360 min) to each aggregate material, and the frictional properties of the unpolished and polished aggregates were evaluated using a British pendulum tester (BPT) and a dynamic friction tester (DFT). Texture and angularity of the unpolished and polished aggregates were also evaluated using the second-generation Aggregate Image Measurement System (AIMS2). Carbonate aggregates were generally found to exhibit higher initial friction than natural gravels, but some carbonate aggregates provided poor friction retention after polishing. Slag aggregates were found to have high initial friction properties and good friction retention, while the trap rock used in this study exhibited relatively low initial friction and poor friction retention. It was found in this study that mass loss after abrasion in the micro-Deval test is not a good indicator of the aggregate’s resistance to polishing. Some aggregates exhibited high mass loss but maintained high friction properties, while others showed low mass loss and poor friction retention. The AIMS2 texture was also found to have a relatively low correlation with direct contact friction measurements obtained using the BPT and the DFT. These findings confirm the need for direct contact friction measurements to properly characterize aggregate susceptibility to polishing.


  • Evaluation of Moisture Damage in Asphalt Mixtures at Macro- and Nanoscales

    by Munir D. Nazzal, Lana Abu Qtaish, Ahmad Al-Hosainat, Sk Abu Talha, Savas Kaya, Ala R. Abbas

    The aim of this study was to examine the effects of different additives on the moisture resistance of asphalt binders using atomic force microscopy (AFM), and to correlate the results with those obtained in macroscale tests. To this end, AFM force spectroscopy was conducted on neat and polymer-modified asphalt binders produced using various warm mix asphalt (WMA) technologies. The technologies considered included Sasobit, Advera, foamed WMA, and Evotherm M1. Furthermore, the asphalt mixtures were prepared using the considered asphalt binders and were tested using the AASHTO T 283 test. The results of this study show that the most significant factor affecting the AFM adhesive forces of asphalt binders is the use of polymer additives. However, the interactions between various chemical groups in asphalt binders and the considered additives differ. Finally, it was found that the effect of aggregate-binder adhesive bonds on indirect tensile strength is greater than that of the binder’s cohesive bonds, as the cracking in this AASHTO T 283 test has more tendency to occur at the interface between the aggregate and the binder due to the high stress concentration.


  • Accuracy of MEPDG Dynamic Modulus Predictions for Short-Term and Long-Term Aged Asphalt Mixtures

    by Mir S. Arefin, Tanvir Quasem, Munir Nazzal, Samer Dessouky, Ala R. Abbas

    This study examines the accuracy of dynamic modulus, |E*| , predictions made by the Mechanistic-Empirical Pavement Design Guide (MEPDG) for short-term and long-term aged hot mix asphalt (HMA) and foamed warm mix asphalt (WMA) mixtures. Four asphalt binders and one aggregate were used in the preparation of the asphalt mixtures. The American Association of State Highway and Transportation Officials (AASHTO) standard test method, AASHTO R 30, was used to simulate the short-term and long-term aging of laboratory-produced asphalt mixtures, while the National Cooperative Highway Research Program (NCHRP) 1-37A and NCHRP 1-40D prediction models, along with the Global Aging System that are incorporated into the MEPDG, were used to predict the dynamic modulus of the short-term and long-term aged HMA and foamed WMA mixtures. By comparing the dynamic modulus predictions obtained using the MEPDG to |E*| measurements obtained in the laboratory for short-term and long-term aged HMA and foamed WMA mixtures, it was observed that the NCHRP 1-37A model generally underestimated the dynamic modulus of the HMA mixtures (R2 close to 0.80) but provided a better quality of fit for the foamed WMA mixtures (R2 close to 0.90). As for the NCHRP 1-40D model, which generally resulted in higher |E*| predictions than the NCHRP 1-37A model, it had a better quality of fit for both HMA and foamed WMA mixtures with an R2 value close to 0.90 for both mixtures, with little difference observed between the R2 values for the short-term and long-term aged mixtures.