Changhua Yang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Changhua Yang has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
Bo Yu
Technology Monitoring Center of PetroChina Changqing Oilfield Company, Xi’an 710018, China
1 shared publication- Chen Wang
School of Petroleum Engineering, Xi’an Shiyou University, Xi’an 710065, China
1 shared publication - Chunning Gao
Research Institute of Exploration and Development, Changqing Oilfield Company, Petro China, Xi’an 710021, China
1 shared publication - Di Xiao
School of Petroleum Engineering, Xi’an Shiyou University, Xi’an 710065, China
1 shared publication - Futeng Feng
School of Petroleum Engineering, Xi’an Shiyou University, Xi’an 710065, China
1 shared publication - Huilin Wang
Research Institute of Exploration and Development, Changqing Oilfield Company, PetroChina, Xi’an 710018, China
1 shared publication
Latest Publications
- Open Access
Experimental Study on CO2–Crude Oil Phase Behavior, Miscibility and Threshold Pressure Gradient for CCUS in Ultra-Low Permeability Reservoir
The Chang 8 reservoir in the Baima Middle Block of the Ordos Basin is an ultra-low-permeability reservoir that has faced formation-pressure depletion, a rising water cut, and poor remaining-oil recovery during long-term water-injection development. CO2 flooding in CCUS can simultaneously enhance oil recovery and achieve carbon sequestration; however, comprehensive and integrated research on the CO2–crude oil phase behavior, miscibility characteristics, and nonlinear flow in porous media for this block is still lacking. To address this gap, this study used crude oil and natural cores from the block and natural cores to conduct a series of experiments at 70 °C, including PVT high-pressure physical-property tests, CO2 constant-mass-expansion tests, slim-tube minimum-miscibility-pressure (MMP) tests, pendant-drop oil–gas interfacial-tension measurements, and CO2-flooding threshold-pressure-gradient measurements in cores of different permeability. The results showed that as the CO2 mole fraction increased from 0% to 61.78%, the bubble-point pressure of the crude oil rose from 17.424 to 22.575 MPa, the viscosity decreased from 9.026 to 4.906 mPa·s, and the volumetric expansion coefficient increased from 1.0000 to 1.1454. As the water cut increased from 0% to 80%, the apparent MMP of CO2 increased from 15.83 to 17.69 MPa. The oil–gas interfacial tension gradually decreased with increasing system pressure, and droplet instability and atomization occurred under near-miscible high-pressure conditions. The CO2-flooding threshold pressure gradient decreased with core permeability following a power-law relationship, and a knee-like trend appeared near 0.5 mD within the limited permeability dataset of this study; this trend cannot be generalized without further experimental evidence. This study comprehensively reveals the coupled mechanisms of phase behavior, miscibility, and nonlinear flow during CO2 flooding in the target block, providing experimental and theoretical support for optimizing the injection pressure and reservoir-stimulation schemes of CCUS-EOR in ultra-low-permeability reservoirs.
Open AccessExperimental Study on CO2–Crude Oil Phase Behavior, Miscibility and Threshold Pressure Gradient for CCUS in Ultra-Low Permeability Reservoir
The Chang 8 reservoir in the Baima Middle Block of the Ordos Basin is an ultra-low-permeability reservoir that has faced formation-pressure depletion, a rising water cut, and poor remaining-oil recovery during long-term water-injection development. CO2 flooding in CCUS can simultaneously enhance oil recovery and achieve carbon sequestration; however, comprehensive and integrated research on the CO2–crude oil phase behavior, miscibility characteristics, and nonlinear flow in porous media for this block is still lacking. To address this gap, this study used crude oil and natural cores from the block and natural cores to conduct a series of experiments at 70 °C, including PVT high-pressure physical-property tests, CO2 constant-mass-expansion tests, slim-tube minimum-miscibility-pressure (MMP) tests, pendant-drop oil–gas interfacial-tension measurements, and CO2-flooding threshold-pressure-gradient measurements in cores of different permeability. The results showed that as the CO2 mole fraction increased from 0% to 61.78%, the bubble-point pressure of the crude oil rose from 17.424 to 22.575 MPa, the viscosity decreased from 9.026 to 4.906 mPa·s, and the volumetric expansion coefficient increased from 1.0000 to 1.1454. As the water cut increased from 0% to 80%, the apparent MMP of CO2 increased from 15.83 to 17.69 MPa. The oil–gas interfacial tension gradually decreased with increasing system pressure, and droplet instability and atomization occurred under near-miscible high-pressure conditions. The CO2-flooding threshold pressure gradient decreased with core permeability following a power-law relationship, and a knee-like trend appeared near 0.5 mD within the limited permeability dataset of this study; this trend cannot be generalized without further experimental evidence. This study comprehensively reveals the coupled mechanisms of phase behavior, miscibility, and nonlinear flow during CO2 flooding in the target block, providing experimental and theoretical support for optimizing the injection pressure and reservoir-stimulation schemes of CCUS-EOR in ultra-low-permeability reservoirs.
- Open Access
Preparation and Performance Evaluation of a Core–Shell Nanosphere/Surfactant Composite System for Profile Control and Enhanced Oil Recovery in Low-Permeability Reservoirs
To address early water breakthrough and poor residual-oil mobilization in low-permeability reservoirs, a core–shell nanosphere/surfactant composite system was developed for profile control and enhanced oil recovery. The core–shell nanospheres were prepared by a semi-continuous seed-growth method, and a target particle-size window of 100–200 nm was selected based on pore-throat/particle matching. The representative sample, HK-0417, had an average particle size of about 120 nm and showed good dispersion stability in formation brine at 45 °C. After blending with the surfactant ALT-603, the system achieved an ultralow oil–water interfacial tension on the order of 10−3 mN/m and reduced the water contact angle of the oil-aged surface from 125° to 70°, indicating a shift toward near-neutral wettability. Core-flooding tests further showed that, under the same chemical dosage, slug injection (HK-0417 followed by ALT-603) demonstrated better performance than co-injection, with higher incremental oil recovery (15.49% vs. 13.17%) and higher plugging efficiency during subsequent water flooding (81.25% vs. 78.46%). The novelty of this work lies in integrating particle-size-window design, controllable preparation of core–shell nanospheres, and direct comparison of injection strategies within one system. The results provide practical guidance for formulation design and injection-mode selection for enhanced oil recovery in low-permeability reservoirs.
Open AccessPreparation and Performance Evaluation of a Core–Shell Nanosphere/Surfactant Composite System for Profile Control and Enhanced Oil Recovery in Low-Permeability Reservoirs
To address early water breakthrough and poor residual-oil mobilization in low-permeability reservoirs, a core–shell nanosphere/surfactant composite system was developed for profile control and enhanced oil recovery. The core–shell nanospheres were prepared by a semi-continuous seed-growth method, and a target particle-size window of 100–200 nm was selected based on pore-throat/particle matching. The representative sample, HK-0417, had an average particle size of about 120 nm and showed good dispersion stability in formation brine at 45 °C. After blending with the surfactant ALT-603, the system achieved an ultralow oil–water interfacial tension on the order of 10−3 mN/m and reduced the water contact angle of the oil-aged surface from 125° to 70°, indicating a shift toward near-neutral wettability. Core-flooding tests further showed that, under the same chemical dosage, slug injection (HK-0417 followed by ALT-603) demonstrated better performance than co-injection, with higher incremental oil recovery (15.49% vs. 13.17%) and higher plugging efficiency during subsequent water flooding (81.25% vs. 78.46%). The novelty of this work lies in integrating particle-size-window design, controllable preparation of core–shell nanospheres, and direct comparison of injection strategies within one system. The results provide practical guidance for formulation design and injection-mode selection for enhanced oil recovery in low-permeability reservoirs.
- Open Access
Evaluation and Experiment of High-Strength Temperature- and Salt-Resistant Gel System
To address the issues of poor thermal stability, inadequate salt tolerance, and environmental risks in conventional gel systems for the development of high-temperature, high-salinity heterogeneous reservoirs, a triple-synergy gel system comprising anionic polyacrylamide (APAM), polyethyleneimine (PEI), and phenolic resin (SMP) was developed in this study. The optimal synthesis parameters—APAM of 180 mg/L, PEI:SMP = 3:1, salinity of 150,000 ppm, and temperature of 110 °C—were determined via response surface methodology, and a time–viscosity model was established. Compared with existing binary systems, the proposed gel exhibited a mass retention rate of 93.48% at 110 °C, a uniform porous structure (pore size of 2–8 μm), and structural stability under high salinity (150,000 ppm). Nuclear magnetic resonance displacement tests showed that the utilization efficiency of crude oil in 0.1–1 μm micropores increased to 21.32%. Parallel dual-core flooding experiments further confirmed the selective plugging capability in heterogeneous systems with a permeability contrast of 10:1: The high-permeability layer (500 mD) achieved a plugging rate of 98.7%, while the recovery factor of the low-permeability layer increased by 13.6%. This gel system provides a green and efficient profile control solution for deep, high-temperature, high-salinity reservoirs.
Open AccessEvaluation and Experiment of High-Strength Temperature- and Salt-Resistant Gel System
To address the issues of poor thermal stability, inadequate salt tolerance, and environmental risks in conventional gel systems for the development of high-temperature, high-salinity heterogeneous reservoirs, a triple-synergy gel system comprising anionic polyacrylamide (APAM), polyethyleneimine (PEI), and phenolic resin (SMP) was developed in this study. The optimal synthesis parameters—APAM of 180 mg/L, PEI:SMP = 3:1, salinity of 150,000 ppm, and temperature of 110 °C—were determined via response surface methodology, and a time–viscosity model was established. Compared with existing binary systems, the proposed gel exhibited a mass retention rate of 93.48% at 110 °C, a uniform porous structure (pore size of 2–8 μm), and structural stability under high salinity (150,000 ppm). Nuclear magnetic resonance displacement tests showed that the utilization efficiency of crude oil in 0.1–1 μm micropores increased to 21.32%. Parallel dual-core flooding experiments further confirmed the selective plugging capability in heterogeneous systems with a permeability contrast of 10:1: The high-permeability layer (500 mD) achieved a plugging rate of 98.7%, while the recovery factor of the low-permeability layer increased by 13.6%. This gel system provides a green and efficient profile control solution for deep, high-temperature, high-salinity reservoirs.
- Open Access
- 24 September 2024
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 14 (42) , 31183-31192
Study on the imbibition production mechanism and main controlling factors of low-permeability reservoir
With high water cuts and high permeability reservoirs entering the middle and late stage, many old oil fields in China are facing the dilemma of oil and gas resource exhaustion, while low-permeability reservoir resources remain very rich.
- 24 September 2024
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 14 (42) , 31183-31192
Open AccessStudy on the imbibition production mechanism and main controlling factors of low-permeability reservoir
With high water cuts and high permeability reservoirs entering the middle and late stage, many old oil fields in China are facing the dilemma of oil and gas resource exhaustion, while low-permeability reservoir resources remain very rich.
- Open Access
Preparation and Effect of CO2 Response Gel for Plugging Low-Permeability Reservoirs
In order to solve the problem of gas channeling during CO2 flooding in low-permeability reservoirs, a novel CO2 responsive gel channeling system was prepared by using carrageenan, branched polyethylene imide and ethylenediamine under laboratory conditions. Based on the Box–Behnken response surface design method, the optimal synthesis concentration of the system was 0.5 wt% carrageenan, 2.5 wt% branchized polyethylenimide and 6.5 wt% ethylenediamine. The micromorphology of the system before and after response was characterized by scanning electron microscopy. The rheology and dehydration rate were tested under different conditions. The channeling performance and enhanced oil recovery effect of the gel system were simulated by a core displacement experiment. The experimental results show that the internal structure of the system changes from a disordered, smooth and loosely separated lamellae structure to a more uniform, complete and orderly three-dimensional network structure after exposure to CO2. The viscosity of the system was similar to aqueous solution before contact with CO2 and showed viscoelastic solid properties after contact with CO2. The experiment employing dehydration rates at different temperatures showed that the internal structure of the gel would change at a high temperature, but the gel system had a certain self-healing ability. The results of the displacement experiment show that the plugging rate of the gel system is stable at 85.32% after CO2 contact, and the recovery rate is increased by 17.06%, which provides an important guide for the development of low-permeability reservoirs.
Open AccessPreparation and Effect of CO2 Response Gel for Plugging Low-Permeability Reservoirs
In order to solve the problem of gas channeling during CO2 flooding in low-permeability reservoirs, a novel CO2 responsive gel channeling system was prepared by using carrageenan, branched polyethylene imide and ethylenediamine under laboratory conditions. Based on the Box–Behnken response surface design method, the optimal synthesis concentration of the system was 0.5 wt% carrageenan, 2.5 wt% branchized polyethylenimide and 6.5 wt% ethylenediamine. The micromorphology of the system before and after response was characterized by scanning electron microscopy. The rheology and dehydration rate were tested under different conditions. The channeling performance and enhanced oil recovery effect of the gel system were simulated by a core displacement experiment. The experimental results show that the internal structure of the system changes from a disordered, smooth and loosely separated lamellae structure to a more uniform, complete and orderly three-dimensional network structure after exposure to CO2. The viscosity of the system was similar to aqueous solution before contact with CO2 and showed viscoelastic solid properties after contact with CO2. The experiment employing dehydration rates at different temperatures showed that the internal structure of the gel would change at a high temperature, but the gel system had a certain self-healing ability. The results of the displacement experiment show that the plugging rate of the gel system is stable at 85.32% after CO2 contact, and the recovery rate is increased by 17.06%, which provides an important guide for the development of low-permeability reservoirs.
- Open Access
- 5 December 2023
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 8 (50) , 48280-48291
Investigations of Water Transport in Shale Reservoir with Dual-Wettability by Using Monte Carlo Method
How liquids transport in the shale system has been the focus because of fracturing fluid loss. In this study, a single-nanopore model is established for liquid transport in shale while considering the slip effect and effective viscosity of confined fluids. Then, the fractal Monte Carlo (FMC) model is proposed to upscale the single-pore model into shale porous media. The effects of different transport mechanisms, shale wettability, and pore characteristic parameters on confined liquid flow in shale rock are investigated. Results show that FMC permeabilities are 2-3 orders of magnitude larger than intrinsic and slip-corrected permeabilities in organic matter. However, the slip effect and effective viscosity have little influence on water flow in inorganic matter. With the contact angle of organic pore (θom) increasing and contact angle of inorganic pore (θin) decreasing, the effective permeability of the whole shale matrix grows in number. The enhancement factor in the situation of θom = 170° and θin = 20° is 4 orders of magnitude larger than the case of θom = 130° and θin = 40°, although the close effective macroscopic contact angle (θeff = 80°) occurs in these two cases, which indicates that shale microscopic wettability has a significant impact on the confined liquid transport. Moreover, with the increase of porosity and maximum pore diameters, shale permeability increases rapidly, but the enhancement factor has the opposite trend. Compared with the tiny impact of the variance of minimum inorganic pore diameters, minimum organic pore diameters have more significant impacts on liquid flow in shale systems, and the enhancement factor also rapidly increases up to 30 times for the case of 0.5 nm because of the strong slip effect.
- 5 December 2023
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 8 (50) , 48280-48291
Open AccessInvestigations of Water Transport in Shale Reservoir with Dual-Wettability by Using Monte Carlo Method
How liquids transport in the shale system has been the focus because of fracturing fluid loss. In this study, a single-nanopore model is established for liquid transport in shale while considering the slip effect and effective viscosity of confined fluids. Then, the fractal Monte Carlo (FMC) model is proposed to upscale the single-pore model into shale porous media. The effects of different transport mechanisms, shale wettability, and pore characteristic parameters on confined liquid flow in shale rock are investigated. Results show that FMC permeabilities are 2-3 orders of magnitude larger than intrinsic and slip-corrected permeabilities in organic matter. However, the slip effect and effective viscosity have little influence on water flow in inorganic matter. With the contact angle of organic pore (θom) increasing and contact angle of inorganic pore (θin) decreasing, the effective permeability of the whole shale matrix grows in number. The enhancement factor in the situation of θom = 170° and θin = 20° is 4 orders of magnitude larger than the case of θom = 130° and θin = 40°, although the close effective macroscopic contact angle (θeff = 80°) occurs in these two cases, which indicates that shale microscopic wettability has a significant impact on the confined liquid transport. Moreover, with the increase of porosity and maximum pore diameters, shale permeability increases rapidly, but the enhancement factor has the opposite trend. Compared with the tiny impact of the variance of minimum inorganic pore diameters, minimum organic pore diameters have more significant impacts on liquid flow in shale systems, and the enhancement factor also rapidly increases up to 30 times for the case of 0.5 nm because of the strong slip effect.
- Open Access
A Study on the Oil-Bearing Stability of Salt-Resistant Foam and an Explanation of the Viscoelastic Phenomenon
Foam is a medium-stable system composed of gas and liquid phases, which has the advantages of low density at the gas phase and high viscosity at the liquid phase, and has a wide application in oil and gas field development and mineral flotation, but its special medium-stable system also brings many problems in industry applications. Scientists have carried out extensive analyses and research on the foam stability and bubble-bursting mechanism, which initially clarified the rules of bubble breakage caused by environmental factors such as temperature and pressure, but the mechanism of bubble bursting under the action of internal factors such as liquid mineralization and oil concentration of the films is still not clearly defined. In this paper, we propose a compound salt-resistant foaming agent, investigated the influence of the aggregation and adsorption behavior of oil droplets on the liquid films and boundaries, and established a relevant aggregation and adsorption model with the population balance equation. We put forward a liquid film drainage mechanism based on the distribution, aggregation, and transport of oil droplets in the liquid films, so as to explain the changes in foam stability under the action of oil droplets. On the other hand, the viscoelastic analysis of foam fluid is performed with a rheometer, and the results show that in comparison with conventional power-law fluid, foam fluid has a complex rheological behavior for low shear thickening, but high shear thinning.
Open AccessA Study on the Oil-Bearing Stability of Salt-Resistant Foam and an Explanation of the Viscoelastic Phenomenon
Foam is a medium-stable system composed of gas and liquid phases, which has the advantages of low density at the gas phase and high viscosity at the liquid phase, and has a wide application in oil and gas field development and mineral flotation, but its special medium-stable system also brings many problems in industry applications. Scientists have carried out extensive analyses and research on the foam stability and bubble-bursting mechanism, which initially clarified the rules of bubble breakage caused by environmental factors such as temperature and pressure, but the mechanism of bubble bursting under the action of internal factors such as liquid mineralization and oil concentration of the films is still not clearly defined. In this paper, we propose a compound salt-resistant foaming agent, investigated the influence of the aggregation and adsorption behavior of oil droplets on the liquid films and boundaries, and established a relevant aggregation and adsorption model with the population balance equation. We put forward a liquid film drainage mechanism based on the distribution, aggregation, and transport of oil droplets in the liquid films, so as to explain the changes in foam stability under the action of oil droplets. On the other hand, the viscoelastic analysis of foam fluid is performed with a rheometer, and the results show that in comparison with conventional power-law fluid, foam fluid has a complex rheological behavior for low shear thickening, but high shear thinning.
- Open Access
Study on the Plugging Limit and Combination of CO2 Displacement Flow Control System Based on Nuclear Magnetic Resonance (NMR)
CO2 displacement is an important technology to reduce emissions and improve crude oil recovery, as well as prevent CO2 escape. Effective storage is key to the successful implementation of this technology, especially for medium and high permeability reservoirs. The current flow control systems that are applied to seal gas escape are mainly gas/water alternation, CO2 foam, and CO2 foam gel, but there is no clear understanding of the plugging limits of various flow control systems and the mechanism of their combined use of residual oil. Therefore, in this paper, a series of core replacement experiments are conducted for different flow control systems and their combinations. The quantitative characterization of the core pore size distribution before and after the replacement is carried out using the NMR technique to try and determine the plugging limits of different plugging systems, and to investigate the residual oil utilization patterns of self-designed flow control system combinations and common flow control system combinations under two reservoir conditions with and without large pores. The results show that the plugging limits of water/gas alternation, CO2 foam, and CO2 foam gel systems are 0.86–21.35 μm, 0.07–28.23 μm, and 7–100 μm, respectively, as inferred from the T2 (lateral relaxation time) distribution and pore size distribution. When different combinations of flow control systems are used for repelling, for reservoirs without large pore channels, the combination of flow control systems using higher strength CO2 foam first can effectively improve the degree of crude oil mobilization in small pore throats, compared to using gas/water alternation directly. For reservoirs containing large pore channels, using high-strength CO2 foam gel first to seal the large pore channels increases the degree of utilization of the large pore channels; using water/gas alternation first causes damage to the middle pore channels; High-strength CO2 foam gel seals the large pore channels when the plugging strength is not enough; and using water/gas alternation can effectively improve the degree of utilization of small and medium pore channels. The results of this paper can provide theoretical guidance for the multi-stage flow control of CO2 displacement in the field.
Open AccessStudy on the Plugging Limit and Combination of CO2 Displacement Flow Control System Based on Nuclear Magnetic Resonance (NMR)
CO2 displacement is an important technology to reduce emissions and improve crude oil recovery, as well as prevent CO2 escape. Effective storage is key to the successful implementation of this technology, especially for medium and high permeability reservoirs. The current flow control systems that are applied to seal gas escape are mainly gas/water alternation, CO2 foam, and CO2 foam gel, but there is no clear understanding of the plugging limits of various flow control systems and the mechanism of their combined use of residual oil. Therefore, in this paper, a series of core replacement experiments are conducted for different flow control systems and their combinations. The quantitative characterization of the core pore size distribution before and after the replacement is carried out using the NMR technique to try and determine the plugging limits of different plugging systems, and to investigate the residual oil utilization patterns of self-designed flow control system combinations and common flow control system combinations under two reservoir conditions with and without large pores. The results show that the plugging limits of water/gas alternation, CO2 foam, and CO2 foam gel systems are 0.86–21.35 μm, 0.07–28.23 μm, and 7–100 μm, respectively, as inferred from the T2 (lateral relaxation time) distribution and pore size distribution. When different combinations of flow control systems are used for repelling, for reservoirs without large pore channels, the combination of flow control systems using higher strength CO2 foam first can effectively improve the degree of crude oil mobilization in small pore throats, compared to using gas/water alternation directly. For reservoirs containing large pore channels, using high-strength CO2 foam gel first to seal the large pore channels increases the degree of utilization of the large pore channels; using water/gas alternation first causes damage to the middle pore channels; High-strength CO2 foam gel seals the large pore channels when the plugging strength is not enough; and using water/gas alternation can effectively improve the degree of utilization of small and medium pore channels. The results of this paper can provide theoretical guidance for the multi-stage flow control of CO2 displacement in the field.