Ranjitha Kumarapuram Hariharalakshmanan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ranjitha Kumarapuram Hariharalakshmanan has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
Tansel Karabacak
School of Physical Sciences, University of Arkansas at Little Rock, Little Rock, USA
3 shared publications- Tansel Karabacak
School of Physical Sciences, University of Arkansas at Little Rock, Little Rock, USA
3 shared publications Busra Ergul-Yilmaz
School of Physical Sciences, University of Arkansas at Little Rock, Little Rock, USA
2 shared publications- Chao Yang
The Center for Materials, Devices, and Integrated Systems, Rensselaer Polytechnic Institute 2 , Troy, New York 12180
1 shared publication Cindy White
Department of Chemistry, Harding University, Searcy, USA
1 shared publicationDakota Ungerbuehler
Department of Chemistry, Harding University, Searcy, USA
1 shared publication
Latest Publications
- 31 July 2026
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 44 (5)
Surface morphology and oxide phases of Cu pads in vias under thermal annealing in air
Thermal annealing of Cu, including oxidation and grain growth, plays a crucial role in the reliability performance of microelectronic devices. We present an experimental analysis of Cu oxide growth in dielectric-confined Cu pads in vias, essential for the development of a reliable Cu/oxide hybrid bonding process. Thermal oxidation of Cu pads grown by electroplating and processed by dual damascene was performed at a fixed annealing temperature (Ta) from 200 to 350 °C for 30 min under ambient air. As the temperature increases, the Cu pad expands and bulges above the dielectric surface. The surface morphology and roughness of Cu pad were examined by atomic force microscopy. The evolution of Cu oxide phases versus Ta was examined by Raman spectroscopy. At low Ta, the Cu2O phase dominates. As Ta increases, the CuO phase appears at 250 °C and coexists with the Cu2O phase. The energy dispersive x-ray spectroscopy shows that Cu oxide phases exist in the bulged-out Cu pad and can be detached from the unoxidized part of the Cu pad beneath the dielectric surface. The focused ion beam cross sections of Cu pads show a boundary region with gaps and void between oxidized Cu and unoxidized Cu pads. This understanding is relevant for the reliability of hybrid bonding in microelectronic Cu interconnects.
- 31 July 2026
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 44 (5)
Surface morphology and oxide phases of Cu pads in vias under thermal annealing in air
Thermal annealing of Cu, including oxidation and grain growth, plays a crucial role in the reliability performance of microelectronic devices. We present an experimental analysis of Cu oxide growth in dielectric-confined Cu pads in vias, essential for the development of a reliable Cu/oxide hybrid bonding process. Thermal oxidation of Cu pads grown by electroplating and processed by dual damascene was performed at a fixed annealing temperature (Ta) from 200 to 350 °C for 30 min under ambient air. As the temperature increases, the Cu pad expands and bulges above the dielectric surface. The surface morphology and roughness of Cu pad were examined by atomic force microscopy. The evolution of Cu oxide phases versus Ta was examined by Raman spectroscopy. At low Ta, the Cu2O phase dominates. As Ta increases, the CuO phase appears at 250 °C and coexists with the Cu2O phase. The energy dispersive x-ray spectroscopy shows that Cu oxide phases exist in the bulged-out Cu pad and can be detached from the unoxidized part of the Cu pad beneath the dielectric surface. The focused ion beam cross sections of Cu pads show a boundary region with gaps and void between oxidized Cu and unoxidized Cu pads. This understanding is relevant for the reliability of hybrid bonding in microelectronic Cu interconnects.
- Open Access
Influence of Substrate Location and Temperature Variation on the Growth of ZnO Nanorods Synthesized by Hot Water Treatment
Hot water treatment (HWT) is a versatile technique for synthesizing metal oxide nanostructures (MONSTRs) by immersing metal substrates in hot water, typically in glass beakers. The proximity of substrates to the heat source during HWT can influence the temperature of the substrate and subsequently impact MONSTR growth. In our study, zinc (Zn) substrates underwent HWT at the base of a glass beaker in contact with a hot plate and at four different vertical distances from the base. While the set temperature of deionized (DI) water was 75.0 °C, the substrate locations exhibited variations, notably with the base reaching 95.0 °C. Scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), and Raman spectroscopy showed stoichiometric and crystalline zinc oxide (ZnO) nanorods. ZnO rods on the base, exposed to higher temperatures, displayed greater growth in length and diameter, and higher crystallinity. Nanorods with increasing vertical distances from the base exhibited a logarithmic decrease in length despite identical temperatures, whereas their diameters remained constant. We attribute these findings to crucial HWT growth mechanisms like surface diffusion and “plugging”, influenced by temperature and water flow within the beaker. Our results provide insights for optimizing synthesis parameters to effectively control MONSTR growth through HWT.
Open AccessInfluence of Substrate Location and Temperature Variation on the Growth of ZnO Nanorods Synthesized by Hot Water Treatment
Hot water treatment (HWT) is a versatile technique for synthesizing metal oxide nanostructures (MONSTRs) by immersing metal substrates in hot water, typically in glass beakers. The proximity of substrates to the heat source during HWT can influence the temperature of the substrate and subsequently impact MONSTR growth. In our study, zinc (Zn) substrates underwent HWT at the base of a glass beaker in contact with a hot plate and at four different vertical distances from the base. While the set temperature of deionized (DI) water was 75.0 °C, the substrate locations exhibited variations, notably with the base reaching 95.0 °C. Scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), and Raman spectroscopy showed stoichiometric and crystalline zinc oxide (ZnO) nanorods. ZnO rods on the base, exposed to higher temperatures, displayed greater growth in length and diameter, and higher crystallinity. Nanorods with increasing vertical distances from the base exhibited a logarithmic decrease in length despite identical temperatures, whereas their diameters remained constant. We attribute these findings to crucial HWT growth mechanisms like surface diffusion and “plugging”, influenced by temperature and water flow within the beaker. Our results provide insights for optimizing synthesis parameters to effectively control MONSTR growth through HWT.
- 22 November 2023
- Published by Springer Nature in MRS Advances
- Vol. 9 (12) , 979-985
Cyclic voltammetry and specific capacitance studies of copper oxide nanostructures grown by hot water treatment
- 22 November 2023
- Published by Springer Nature in MRS Advances
- Vol. 9 (12) , 979-985
Cyclic voltammetry and specific capacitance studies of copper oxide nanostructures grown by hot water treatment
- 17 March 2023
- Published by Springer Nature in Water, Air, & Soil Pollution
- Vol. 234 (4) , 1-14
Suspension of ZnO Nanostructures Synthesized by Hot Water Treatment for Photocatalytic Wastewater Treatment
- 17 March 2023
- Published by Springer Nature in Water, Air, & Soil Pollution
- Vol. 234 (4) , 1-14
Suspension of ZnO Nanostructures Synthesized by Hot Water Treatment for Photocatalytic Wastewater Treatment
- Open Access
In Situ Growth and UV Photocatalytic Effect of ZnO Nanostructures on a Zn Plate Immersed in Methylene Blue
Nanostructures of zinc oxide (ZnO) are considered promising photocatalysts for the degradation of organic pollutants in water. This work discusses an in situ growth and UV photocatalytic effect of ZnO nanostructures on a Zn plate immersed in methylene blue (MB) at room temperature. First, the Zn surfaces were pretreated via sandblasting to introduce a micro-scale roughness. Then, the Zn plates were immersed in MB and exposed to UV light, to observe ZnO nanostructure growth and photocatalytic degradation of MB. Scanning electron microscopy, energy dispersive spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and UV-Vis diffuse reflectance spectroscopy were used to characterize the Zn surfaces. We observed the growth of stoichiometric and crystalline ZnO with a nano-leaf morphology and an estimated bandgap of 3.08 eV. The photocatalytic degradation of MB was also observed in the presence of the ZnO nanostructures and UV light. The average percentage degradation was 76% in 4 h, and the degradation rate constant was 0.3535 h−1. The experimental results suggest that room temperature growth of ZnO nanostructures (on Zn surfaces) in organic dye solutions is possible. Furthermore, the nanostructured surface can be used simultaneously for the photocatalytic degradation of the organic dye.
Open AccessIn Situ Growth and UV Photocatalytic Effect of ZnO Nanostructures on a Zn Plate Immersed in Methylene Blue
Nanostructures of zinc oxide (ZnO) are considered promising photocatalysts for the degradation of organic pollutants in water. This work discusses an in situ growth and UV photocatalytic effect of ZnO nanostructures on a Zn plate immersed in methylene blue (MB) at room temperature. First, the Zn surfaces were pretreated via sandblasting to introduce a micro-scale roughness. Then, the Zn plates were immersed in MB and exposed to UV light, to observe ZnO nanostructure growth and photocatalytic degradation of MB. Scanning electron microscopy, energy dispersive spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and UV-Vis diffuse reflectance spectroscopy were used to characterize the Zn surfaces. We observed the growth of stoichiometric and crystalline ZnO with a nano-leaf morphology and an estimated bandgap of 3.08 eV. The photocatalytic degradation of MB was also observed in the presence of the ZnO nanostructures and UV light. The average percentage degradation was 76% in 4 h, and the degradation rate constant was 0.3535 h−1. The experimental results suggest that room temperature growth of ZnO nanostructures (on Zn surfaces) in organic dye solutions is possible. Furthermore, the nanostructured surface can be used simultaneously for the photocatalytic degradation of the organic dye.
- 11 July 2022
- Published by Springer Nature in MRS Advances
- Vol. 7 (31) , 865-869
ZnO nanostructures by hot water treatment for photocatalytic bacterial disinfection
- 11 July 2022
- Published by Springer Nature in MRS Advances
- Vol. 7 (31) , 865-869
ZnO nanostructures by hot water treatment for photocatalytic bacterial disinfection
- 1 September 2020
- Published by Springer Nature in MRS Advances
- Vol. 5 (48-49) , 2457-2465
Zinc Oxide Nanostructures Synthesized by a Simple Hot Water Treatment Method for Photocatalytic Degradation of Organic Pollutants in Water
- 1 September 2020
- Published by Springer Nature in MRS Advances
- Vol. 5 (48-49) , 2457-2465
Zinc Oxide Nanostructures Synthesized by a Simple Hot Water Treatment Method for Photocatalytic Degradation of Organic Pollutants in Water