Yuan Lin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yuan Lin has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
Mingyang Wang
6 shared publications- Zhongwei Zhang
State Key Laboratory of Explosion & Impact and Disaster Prevention & Mitigation, Army Engineering University of PLA, Nanjing 210007, China
6 shared publications Zhongwei Zhang
4 shared publicationsChunming Song
3 shared publications- Jian An Wu
State Key Laboratory of Explosion & Impact and Disaster Prevention & Mitigation Army Engineering University of PLA Nanjing China
3 shared publications - Chunming Song
State Key Laboratory of Disaster Prevention & Mitigation of Explosion & Impact, Army Engineering University of PLA, Nanjing 210007, China
2 shared publications
Latest Publications
- 22 February 2024
- Published by Elsevier in Materials Letters
- Vol. 362
Low-velocity impact responses of UHMWPE fiber/epoxy laminates with plasma treatment and polypyrrole grafting
- 22 February 2024
- Published by Elsevier in Materials Letters
- Vol. 362
Low-velocity impact responses of UHMWPE fiber/epoxy laminates with plasma treatment and polypyrrole grafting
- 22 November 2023
- Published by Elsevier in Composite Structures
- Vol. 328
Effect of stitch density on the damage inhibition and compression strength after high-velocity impact of UHMWPE fiber composites
- 22 November 2023
- Published by Elsevier in Composite Structures
- Vol. 328
Effect of stitch density on the damage inhibition and compression strength after high-velocity impact of UHMWPE fiber composites
- 15 September 2023
- Published by Elsevier in Composite Structures
- Vol. 324
Effects of stacking sequences on the axial compressive buckling behavior and failure characteristics of channel-section CFRP/Al laminate columns
- 15 September 2023
- Published by Elsevier in Composite Structures
- Vol. 324
Effects of stacking sequences on the axial compressive buckling behavior and failure characteristics of channel-section CFRP/Al laminate columns
- 26 September 2022
- Published by Wiley in Polymer Composites
- Vol. 44 (1) , 274-293
Numerical analysis on the energy absorbing characteristics of aluminum/CFRP hybrid tubes under quasi‐static crushing loading
In this study, the axial crushing behavior of aluminum/carbon fiber reinforced plastic (CFRP) hybrid tubes are systematically investigated numerically based on a three‐dimensional (3D) progressive damage model. Experiments concerning hybrid tubes with 1/1 and 2/1 lay‐up configurations are performed first to validate the numerical model. Then, the effects of chamfer at the end, stacking configuration, aluminum‐CFRP bonding state and thickness ratio of individual layers on the energy absorption characteristics of aluminum/CFRP tubes are further numerically analyzed. The simulation results suggest that the 3D progressive damage model can effectively simulate the crushing failure process and reveal the energy dissipation mechanism of aluminum/CFRP hybrid tube under crushing. It is observed that increasing the thickness of the CFRP layer does not promote the energy absorption, but the best energy absorption effect can be obtained by using a 1:1 ratio for the thicknesses of the inner and outer aluminum alloy layers in 2/1 hybrid tube. Finally, the economic performance of 2/1 hybrid tube, 1/1 hybrid tube, and aluminum alloy tube as energy‐absorbing structures is theoretically examined. The balance between mass and cost of the 2/1 hybrid tube is proven to be evidently better than that of the conventional 1/1 hybrid tube.
- 26 September 2022
- Published by Wiley in Polymer Composites
- Vol. 44 (1) , 274-293
Numerical analysis on the energy absorbing characteristics of aluminum/CFRP hybrid tubes under quasi‐static crushing loading
In this study, the axial crushing behavior of aluminum/carbon fiber reinforced plastic (CFRP) hybrid tubes are systematically investigated numerically based on a three‐dimensional (3D) progressive damage model. Experiments concerning hybrid tubes with 1/1 and 2/1 lay‐up configurations are performed first to validate the numerical model. Then, the effects of chamfer at the end, stacking configuration, aluminum‐CFRP bonding state and thickness ratio of individual layers on the energy absorption characteristics of aluminum/CFRP tubes are further numerically analyzed. The simulation results suggest that the 3D progressive damage model can effectively simulate the crushing failure process and reveal the energy dissipation mechanism of aluminum/CFRP hybrid tube under crushing. It is observed that increasing the thickness of the CFRP layer does not promote the energy absorption, but the best energy absorption effect can be obtained by using a 1:1 ratio for the thicknesses of the inner and outer aluminum alloy layers in 2/1 hybrid tube. Finally, the economic performance of 2/1 hybrid tube, 1/1 hybrid tube, and aluminum alloy tube as energy‐absorbing structures is theoretically examined. The balance between mass and cost of the 2/1 hybrid tube is proven to be evidently better than that of the conventional 1/1 hybrid tube.
- Open Access
Crushing Characteristics Comparison between Aluminum/CFRP and Aluminum/CFRP/Aluminum Hybrid Tubes
This study experimentally investigated the axial crushing characteristics of the hybrid tubes with the configuration of aluminum/carbon fiber-reinforced polymer (CFRP) (1/1) and aluminum/CFRP/aluminum (2/1). The effects of geometry size and fiber lay-up sequence on the axial crushing energy-absorption performances and failure modes of the two types of hybrid tubes were compared. The results showed that the energy absorption of the specimens with [0°/90°] lay-up sequence was better than that of the ones with [45°/−45°] lay-up sequence for both types of hybrid tubes. The proper length of the tubes should be selected to avoid too small a length-to-diameter ratio so that a stable and controllable progressive crushing failure mode can be achieved. When the crushing failure process was relatively stable, the specific energy absorption and crushing force efficiency of the 2/1 hybrid tubes were not affected by the geometric size. The energy absorption of the hybrid tubes was higher than the sum of the energy absorption of all the corresponding individual tubes, showing a positive hybrid effect.
Open AccessCrushing Characteristics Comparison between Aluminum/CFRP and Aluminum/CFRP/Aluminum Hybrid Tubes
This study experimentally investigated the axial crushing characteristics of the hybrid tubes with the configuration of aluminum/carbon fiber-reinforced polymer (CFRP) (1/1) and aluminum/CFRP/aluminum (2/1). The effects of geometry size and fiber lay-up sequence on the axial crushing energy-absorption performances and failure modes of the two types of hybrid tubes were compared. The results showed that the energy absorption of the specimens with [0°/90°] lay-up sequence was better than that of the ones with [45°/−45°] lay-up sequence for both types of hybrid tubes. The proper length of the tubes should be selected to avoid too small a length-to-diameter ratio so that a stable and controllable progressive crushing failure mode can be achieved. When the crushing failure process was relatively stable, the specific energy absorption and crushing force efficiency of the 2/1 hybrid tubes were not affected by the geometric size. The energy absorption of the hybrid tubes was higher than the sum of the energy absorption of all the corresponding individual tubes, showing a positive hybrid effect.
- 10 September 2022
- Published by Wiley in Polymer Composites
- Vol. 44 (1) , 89-102
Ballistic impact response and failure mechanism of aluminum/ultrahigh molecular weight polyethylene fiber laminates with different adhesive quantity
The aim of this study is to investigate the effects of metal‐composite interface (MCI) adhesive quantity on the energy absorption and failure behavior of fiber metal laminates (FMLs) under ballistic impact. The dynamic shear and ballistic impact tests were systematically conducted, and CT scan was employed to quantitatively investigate the damage and failure mechanisms of the FMLs. The results reveal that the dynamic shear strength of MCI initially increases and then remains constant with the increase in the adhesive quantity at a constant strain rate. Moreover, the MCI adhesive quantity has a certain influence on the impact energy absorption of FMLs, and the degree of influence is related to the impact velocity. At an impact velocity of 360 m/s, the difference of energy absorption is maximal, approximately 14.7%. The distribution of total debonding area changes with increase in the adhesive quantity. When the impact velocity is 212 m/s, compared to FMLs with the lowest adhesive quantity, the total debonding area of FMLs with the highest adhesive quantity decreases by 774.57 mm2 (9.20%), otherwise the debonding area near the rear aluminum alloy sheet increases by 595.94 mm2 (58.99%).
- 10 September 2022
- Published by Wiley in Polymer Composites
- Vol. 44 (1) , 89-102
Ballistic impact response and failure mechanism of aluminum/ultrahigh molecular weight polyethylene fiber laminates with different adhesive quantity
The aim of this study is to investigate the effects of metal‐composite interface (MCI) adhesive quantity on the energy absorption and failure behavior of fiber metal laminates (FMLs) under ballistic impact. The dynamic shear and ballistic impact tests were systematically conducted, and CT scan was employed to quantitatively investigate the damage and failure mechanisms of the FMLs. The results reveal that the dynamic shear strength of MCI initially increases and then remains constant with the increase in the adhesive quantity at a constant strain rate. Moreover, the MCI adhesive quantity has a certain influence on the impact energy absorption of FMLs, and the degree of influence is related to the impact velocity. At an impact velocity of 360 m/s, the difference of energy absorption is maximal, approximately 14.7%. The distribution of total debonding area changes with increase in the adhesive quantity. When the impact velocity is 212 m/s, compared to FMLs with the lowest adhesive quantity, the total debonding area of FMLs with the highest adhesive quantity decreases by 774.57 mm2 (9.20%), otherwise the debonding area near the rear aluminum alloy sheet increases by 595.94 mm2 (58.99%).
- 9 July 2022
- Published by Wiley in Polymer Composites
- Vol. 43 (8) , 5544-5562
Comparison of stacking sequence on the low‐velocity impact failure mechanisms and energy dissipation characteristics of CFRP/Al hybrid laminates
Compared with the resin‐based composite laminates, fiber metal laminates (FMLs) have superior impact resistance. In this study, investigations were made to reveal the effects of stacking sequence on the low‐velocity failure mechanisms and energy dissipation characteristics of carbon fiber reinforced plastics (CFRP)/Al hybrid laminates with same areal density. Experiments were carried out to characterize the typical mechanical responses. Failure morphologies were evaluated by X‐ray computed tomography scanning techniques. Then numerical simulations based on three‐dimensional progressive damage analysis were applied to reveal the dynamic evolution process and energy dissipation characteristics. Results indicated that plastic deformation of aluminum layers acted as the dominant factor in energy dissipation. Stacking aluminum layers on the exterior surface could increase the absorbed impact energy and reduce the fracture behavior of the component layers. The specimens with more CFRP layers stacked on the surface exhibited more severe fracture behavior of component layers and larger delamination areas, thus promoting the energy dissipated by CFRP cracking and delamination. This work intended to provide practical guidance for the structural design of fiber reinforced polymer/metal hybrid protective structures.
- 9 July 2022
- Published by Wiley in Polymer Composites
- Vol. 43 (8) , 5544-5562
Comparison of stacking sequence on the low‐velocity impact failure mechanisms and energy dissipation characteristics of CFRP/Al hybrid laminates
Compared with the resin‐based composite laminates, fiber metal laminates (FMLs) have superior impact resistance. In this study, investigations were made to reveal the effects of stacking sequence on the low‐velocity failure mechanisms and energy dissipation characteristics of carbon fiber reinforced plastics (CFRP)/Al hybrid laminates with same areal density. Experiments were carried out to characterize the typical mechanical responses. Failure morphologies were evaluated by X‐ray computed tomography scanning techniques. Then numerical simulations based on three‐dimensional progressive damage analysis were applied to reveal the dynamic evolution process and energy dissipation characteristics. Results indicated that plastic deformation of aluminum layers acted as the dominant factor in energy dissipation. Stacking aluminum layers on the exterior surface could increase the absorbed impact energy and reduce the fracture behavior of the component layers. The specimens with more CFRP layers stacked on the surface exhibited more severe fracture behavior of component layers and larger delamination areas, thus promoting the energy dissipated by CFRP cracking and delamination. This work intended to provide practical guidance for the structural design of fiber reinforced polymer/metal hybrid protective structures.
- 20 September 2021
- Published by Wiley in Polymer Composites
- Vol. 42 (12) , 6500-6511
Effect of stacking sequence on multi‐point low‐velocity impact and compression after impact damage mechanisms of UHMWPE composites
Composite materials are susceptible to low velocity impact, which is a very common phenomenon. A large number of studies have been conducted on the single‐point impact on their mechanical properties, but there is a lack of in‐depth exploration on the actual situation of multi‐point impact with a certain angle distribution of impact points. In this paper, three impact points with a certain angle distribution were set to carry out low‐velocity impact (LVI) sequentially, followed by compression after impact (CAI). Digital image correlation system (DIC) and X‐ray micro‐computed tomography techniques (micro‐CT) were used to analyze the mechanical response and failure mechanisms of the specimens. Experimental results demonstrated that the distribution of impact points will directly affect the overall mechanical properties of the material, and the mechanical properties are also sensitive to the stacking sequence. More importantly, it was also found that the boundary conditions have a great influence on the overall mechanical response, which makes the surrounding damage worse.
- 20 September 2021
- Published by Wiley in Polymer Composites
- Vol. 42 (12) , 6500-6511
Effect of stacking sequence on multi‐point low‐velocity impact and compression after impact damage mechanisms of UHMWPE composites
Composite materials are susceptible to low velocity impact, which is a very common phenomenon. A large number of studies have been conducted on the single‐point impact on their mechanical properties, but there is a lack of in‐depth exploration on the actual situation of multi‐point impact with a certain angle distribution of impact points. In this paper, three impact points with a certain angle distribution were set to carry out low‐velocity impact (LVI) sequentially, followed by compression after impact (CAI). Digital image correlation system (DIC) and X‐ray micro‐computed tomography techniques (micro‐CT) were used to analyze the mechanical response and failure mechanisms of the specimens. Experimental results demonstrated that the distribution of impact points will directly affect the overall mechanical properties of the material, and the mechanical properties are also sensitive to the stacking sequence. More importantly, it was also found that the boundary conditions have a great influence on the overall mechanical response, which makes the surrounding damage worse.