Jiahao Zhou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jiahao Zhou has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Weihong Bi
School of Information Science and Engineering, The Key Laboratory for Special Fiber and Fiber Sensor of Hebei Province, Yanshan University, Qinhuangdao, China
5 shared publications - Xinghu Fu
Yanshan University
5 shared publications - Guangwei Fu
School of Information Science and Engineering, The Key Laboratory for Special Fiber and Fiber Sensor of Hebei Province, Yanshan University, Qinhuangdao, China
4 shared publications Wa Jin
School of Information Science and Engineering, Key Laboratory for Special Fiber and Fiber Sensor of Hebei Province, Yanshan University, Qinhuangdao, China
4 shared publicationsYongxiang Zhang
School of Information Science and Engineering, Key Laboratory for Special Fiber and Fiber Sensor of Hebei Province, Yanshan University, Qinhuangdao, China
2 shared publications- Zhexu Huang
School of Information Science and Engineering and the Key Laboratory for Special Fiber and Fiber Sensor of Hebei Province, Yanshan University, Qinhuangdao, China
2 shared publications
Latest Publications
- 10 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (10) , 17175-17183
A Cladding Corrosion Dumbbell-Shaped Structure Incorporating Eccentric Heterogeneous Fiber Sensor for Simultaneous Measurement of Temperature and Curvature
A cladding corrosion dumbbell-shaped structure incorporating eccentric heterogeneous fiber (EHF) for simultaneous measurement of temperature and curvature is proposed. The cascaded structure of the sensor is a single mode fiber (SMF)-EHF-SMF, in which a spherical structure is made at both end of the SMF, and the overall structure of the sensor is a dumbbell-shaped structure. When the temperature and curvature change, the length and refractive index of the optical fiber will vary due to thermal and elastic optical effects. By leveraging the corresponding functional relationships and the coefficient matrix method, the dual-parameter matrix equation for temperature and curvature in the sensor can be derived. Due to the characteristics of EHF, the bending direction and effective refractive index difference are different, allowing for directional discrimination. The experimental results show that within the range of 25 °C to 90 °C, as the temperature increases, the transmission spectrum of the sensor exhibits a red shift phenomenon, with the highest temperature sensitivity reaching 123.3pm/°C; In the range of 0~0.73m-1, the maximum curvature sensitivity in the x, -x, and y directions can reach 13.16nm/m-1. Finally, based on the experimental results, the dual parameter sensing matrix equations in the x, - x, and y directions are obtained. This sensor can achieve curvature and temperature measurement in three different directions, and has great potential in the field of dual parameter sensing. It lays a certain foundation for vector fiber optic sensors and has good research significance.
- 10 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (10) , 17175-17183
A Cladding Corrosion Dumbbell-Shaped Structure Incorporating Eccentric Heterogeneous Fiber Sensor for Simultaneous Measurement of Temperature and Curvature
A cladding corrosion dumbbell-shaped structure incorporating eccentric heterogeneous fiber (EHF) for simultaneous measurement of temperature and curvature is proposed. The cascaded structure of the sensor is a single mode fiber (SMF)-EHF-SMF, in which a spherical structure is made at both end of the SMF, and the overall structure of the sensor is a dumbbell-shaped structure. When the temperature and curvature change, the length and refractive index of the optical fiber will vary due to thermal and elastic optical effects. By leveraging the corresponding functional relationships and the coefficient matrix method, the dual-parameter matrix equation for temperature and curvature in the sensor can be derived. Due to the characteristics of EHF, the bending direction and effective refractive index difference are different, allowing for directional discrimination. The experimental results show that within the range of 25 °C to 90 °C, as the temperature increases, the transmission spectrum of the sensor exhibits a red shift phenomenon, with the highest temperature sensitivity reaching 123.3pm/°C; In the range of 0~0.73m-1, the maximum curvature sensitivity in the x, -x, and y directions can reach 13.16nm/m-1. Finally, based on the experimental results, the dual parameter sensing matrix equations in the x, - x, and y directions are obtained. This sensor can achieve curvature and temperature measurement in three different directions, and has great potential in the field of dual parameter sensing. It lays a certain foundation for vector fiber optic sensors and has good research significance.
- 22 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 23 (19) , 22556-22563
A Directional Curvature Sensor Using Excentric Heterogeneous Fiber Filled PDMS With Spherical Structure
A directional curvature sensor using excentric heterogeneous fiber (EHF) filled PDMS with spherical structure is proposed and prepared. The main structure of the sensor is an EHF cascaded with two spherical structures made of single-mode fibers, the EHF cladding and eccentric core are corroded and filled with PDMS. The asymmetry of the sensor structure causes it to transmit asymmetric modes. It produces different spectral shift effects for bending in different directions, so it can be used for curvature detection in multiple directions. Experimental results show that in the curvature range of 0~0.73 m -1 , the spectrum is red shift when the bending direction is x , and the maximum curvature sensitivity is 15.88 nm/m -1 . When the bending direction is - x , the spectral is blue shift and the maximum curvature sensitivity is 20.66 nm/m -1 . When the bending direction is y , the spectrum is red shift and the maximum curvature sensitivity is 22.14 nm/m -1 . This sensor has a simple structure and high sensitivity, and can be used for precision equipment, intelligent robots, large building structure health monitoring and other areas of curvature detection.
- 22 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 23 (19) , 22556-22563
A Directional Curvature Sensor Using Excentric Heterogeneous Fiber Filled PDMS With Spherical Structure
A directional curvature sensor using excentric heterogeneous fiber (EHF) filled PDMS with spherical structure is proposed and prepared. The main structure of the sensor is an EHF cascaded with two spherical structures made of single-mode fibers, the EHF cladding and eccentric core are corroded and filled with PDMS. The asymmetry of the sensor structure causes it to transmit asymmetric modes. It produces different spectral shift effects for bending in different directions, so it can be used for curvature detection in multiple directions. Experimental results show that in the curvature range of 0~0.73 m -1 , the spectrum is red shift when the bending direction is x , and the maximum curvature sensitivity is 15.88 nm/m -1 . When the bending direction is - x , the spectral is blue shift and the maximum curvature sensitivity is 20.66 nm/m -1 . When the bending direction is y , the spectrum is red shift and the maximum curvature sensitivity is 22.14 nm/m -1 . This sensor has a simple structure and high sensitivity, and can be used for precision equipment, intelligent robots, large building structure health monitoring and other areas of curvature detection.
- 11 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 23 (16) , 18234-18241
A Cascaded Eccentric Hole Fiber Sensor With Dumbbell-Shaped Structure for Large-Range Torsion Measurement
A cascaded eccentric hole fiber (EHF) sensor with dumbbell-shaped structure for large-range torsion measurement is proposed and prepared. It is consisting of an EHF and two sections of single mode fiber (SMF) which are made into spheres by electric discharge. The main sensing structure is SMF sphere-EHF-SMF sphere. In the first sphere structure and EHF fusion point position, the appearance of mode-field mismatch and refractive index perturbation, the non-circular symmetric (NS) higher-order mode (HM) is created, the effective refractive index (ERI) difference between the HM and the fundamental mode (FM) is modulated by the torsion effect during the transmission process, and then the HM interferes with the FM at the second sphere structure. Experimental results show a maximum sensitivity of 0.759 nm/(rad/m) where the sensor undergoes a torsional change from 0 to ±720°. The blue shift occurs in the torsional range of 0 to ±4π rad/m and ±8π to ±12π rad/m, and a red shift in the range of ±4π to ±8π rad/m and ±12π to ±16π rad/m. The periodic shift phenomenon enables the sensor torsion range to be monitored. In addition, the axial strain has very small impact on the results.
- 11 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 23 (16) , 18234-18241
A Cascaded Eccentric Hole Fiber Sensor With Dumbbell-Shaped Structure for Large-Range Torsion Measurement
A cascaded eccentric hole fiber (EHF) sensor with dumbbell-shaped structure for large-range torsion measurement is proposed and prepared. It is consisting of an EHF and two sections of single mode fiber (SMF) which are made into spheres by electric discharge. The main sensing structure is SMF sphere-EHF-SMF sphere. In the first sphere structure and EHF fusion point position, the appearance of mode-field mismatch and refractive index perturbation, the non-circular symmetric (NS) higher-order mode (HM) is created, the effective refractive index (ERI) difference between the HM and the fundamental mode (FM) is modulated by the torsion effect during the transmission process, and then the HM interferes with the FM at the second sphere structure. Experimental results show a maximum sensitivity of 0.759 nm/(rad/m) where the sensor undergoes a torsional change from 0 to ±720°. The blue shift occurs in the torsional range of 0 to ±4π rad/m and ±8π to ±12π rad/m, and a red shift in the range of ±4π to ±8π rad/m and ±12π to ±16π rad/m. The periodic shift phenomenon enables the sensor torsion range to be monitored. In addition, the axial strain has very small impact on the results.
- 18 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 22 (24) , 23990-23996
A Temperature and Strain Dual-Parameter Sensor Based on Conical Four-Core Fiber Combined With a Multimode Fiber
A temperature and strain dual-parameter sensor based on conical four-core fiber combined with a multimode fiber is presented. A sensor based on Mach-Zehnder interferometry is prepared by using single mode fiber (SMF) - multimode fiber (MMF) - four-core fiber (FCF) - SMF and tapering at the fusion point between FCF and SMF. When the temperature and strain change, the length and refractive index of the fiber change due to thermal and elastic effects. Based on the corresponding function relationship and coefficient matrix method, the temperature and strain dual-parameter matrix equation of the sensor can be obtained. The results show that the red shift of the transmission spectrum occurs with the increase of temperature in the range of 40~90°C, and the maximum temperature sensitivity is 85.45pm/°C. At the strain range of 0με~ 800με, the blue shift occurs in the transmission spectrum with the increase of the strain, and the maximum strain sensitivity is -6.76pm/με. Finally, the matrix Equation of the dual-parameter sensor is obtained based on the experimental results. The sensor is simple to make and has high sensitivity. It can measure the temperature and strain parameters in the environment of micro-magnetic field and micro-electric field.
- 18 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 22 (24) , 23990-23996
A Temperature and Strain Dual-Parameter Sensor Based on Conical Four-Core Fiber Combined With a Multimode Fiber
A temperature and strain dual-parameter sensor based on conical four-core fiber combined with a multimode fiber is presented. A sensor based on Mach-Zehnder interferometry is prepared by using single mode fiber (SMF) - multimode fiber (MMF) - four-core fiber (FCF) - SMF and tapering at the fusion point between FCF and SMF. When the temperature and strain change, the length and refractive index of the fiber change due to thermal and elastic effects. Based on the corresponding function relationship and coefficient matrix method, the temperature and strain dual-parameter matrix equation of the sensor can be obtained. The results show that the red shift of the transmission spectrum occurs with the increase of temperature in the range of 40~90°C, and the maximum temperature sensitivity is 85.45pm/°C. At the strain range of 0με~ 800με, the blue shift occurs in the transmission spectrum with the increase of the strain, and the maximum strain sensitivity is -6.76pm/με. Finally, the matrix Equation of the dual-parameter sensor is obtained based on the experimental results. The sensor is simple to make and has high sensitivity. It can measure the temperature and strain parameters in the environment of micro-magnetic field and micro-electric field.
- 15 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 22 (14) , 14118-14127
A Multiparameter Sensor Based on Dumbbell-Shaped Double-Cladding Fiber Structure Cascaded Long Period Fiber Grating
A multi-parameter sensor based on dumbbell-shaped double-cladding fiber (DCF) structure cascaded long period fiber grating (LPFG) is proposed and fabricated. It is formed by discharging between single mode fiber (SMF) and DCF to form a waist-enlarged taper and then cascading two LPFGs. When the fiber is affected by the thermal expansion effect, thermo-optic effect and elasto-optic effect, the resonant peaks formed by inter-mode interference will shift, and the shifts generated by different resonant peaks are also different. By demodulating the wavelength shift of the three resonant peaks, the temperature, refractive index and axial strain can be measured by using the coefficient sensitivity matrix. The experimental results show that the temperature sensitivity of the three resonance peaks is 14.79pm/°C, 69.07pm/°C and 89.83pm/°C in the range of 25°C~80°C. The refractive index sensitivities of three resonance peaks are 14.27nm/RIU, -71.39nm/RIU and -141.07nm/RIU in the range of 1.3355~1.3715. The axial strain sensitivities of three resonance peaks are -2.26pm/με, -2.5pm/με and -3.14pm/με in the range of 75με~525με. The corresponding resolutions are 0.6905°C, 0.00054RIU and 36.323με, respectively. The sensor is simple and has good linearity. It can be widely used in environmental monitoring for different parameter.
- 15 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 22 (14) , 14118-14127
A Multiparameter Sensor Based on Dumbbell-Shaped Double-Cladding Fiber Structure Cascaded Long Period Fiber Grating
A multi-parameter sensor based on dumbbell-shaped double-cladding fiber (DCF) structure cascaded long period fiber grating (LPFG) is proposed and fabricated. It is formed by discharging between single mode fiber (SMF) and DCF to form a waist-enlarged taper and then cascading two LPFGs. When the fiber is affected by the thermal expansion effect, thermo-optic effect and elasto-optic effect, the resonant peaks formed by inter-mode interference will shift, and the shifts generated by different resonant peaks are also different. By demodulating the wavelength shift of the three resonant peaks, the temperature, refractive index and axial strain can be measured by using the coefficient sensitivity matrix. The experimental results show that the temperature sensitivity of the three resonance peaks is 14.79pm/°C, 69.07pm/°C and 89.83pm/°C in the range of 25°C~80°C. The refractive index sensitivities of three resonance peaks are 14.27nm/RIU, -71.39nm/RIU and -141.07nm/RIU in the range of 1.3355~1.3715. The axial strain sensitivities of three resonance peaks are -2.26pm/με, -2.5pm/με and -3.14pm/με in the range of 75με~525με. The corresponding resolutions are 0.6905°C, 0.00054RIU and 36.323με, respectively. The sensor is simple and has good linearity. It can be widely used in environmental monitoring for different parameter.