Michael Arnold
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Michael Arnold has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Arno L. Görne
Fraunhofer Institute for Ceramic Technologies and Systems IKTS Hermsdorf Germany
3 shared publications - Aakash Ashok Naik
Federal Institute for Materials Research and Testing
1 shared publication - Albert Wouter Maijenburg
Martin Luther University Halle-Wittenberg
1 shared publication - Christian Hagendorf
Fraunhofer Center for Silicon‐Photovoltaics CSP 06120 Halle (Saale) Germany
1 shared publication Christiane Schuster
Fraunhofer Institute for Ceramic Technologies and Systems (IKTS), Maria-Reiche-Straße 2, 01109 Dresden, Germany
1 shared publication- David Adner
Fraunhofer Center for Silicon Photovoltaics CSP Halle (Saale) Germany
1 shared publication
Latest Publications
- Open Access
- 22 August 2026
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 109 (8) , e71159
The Influence of Samarium Doping on the Photoelectrochemical (PEC) Activity of SrTiO 3 for Solar Water Splitting
The effect of Sm 3+ doping (0–5 mol%) on the photoelectrochemical properties of SrTiO 3 was systematically investigated as a photoanode candidate for solar water splitting. Dense bulk ceramics synthesized via solid‐state route retained the cubic perovskite structure. Rietveld refinement of the 5 mol% Sm‐doped SrTiO 3 (Sm:STO) sample confirmed successful A‐site substitution with Sm. Photoluminescence emission spectra revealed enhanced emission intensities upon doping, with concentration quenching observed at 5 mol% Sm. UV–Vis diffuse reflectance spectroscopy indicated only a marginal bandgap narrowing (3.18 for pure STO to 3.14 eV for 5% Sm:STO), suggesting that band structure modification alone does not account for the enhancement in the PEC performance. The 1.5% Sm:STO photoanode exhibited the highest photocurrent density of 64 µA cm − 2 at 1.23 V RHE , nearly two orders of magnitude higher than the undoped SrTiO 3 reference. This improvement is attributed to Sm induced grain refinement, increased electrochemically active surface area, and partially to oxygen‐vacancy formation. Mott–Schottky analysis confirmed n‐type conductivity, while chronoamperometry tests verified the material's chemical stability over 3 h under continuous illumination. These findings show that Sm doping could be used to activate bulk SrTiO 3 ceramics, demonstrating the potential of customized perovskites as scalable photoelectrodes for solar water splitting.
- 22 August 2026
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 109 (8) , e71159
Open AccessThe Influence of Samarium Doping on the Photoelectrochemical (PEC) Activity of SrTiO 3 for Solar Water Splitting
The effect of Sm 3+ doping (0–5 mol%) on the photoelectrochemical properties of SrTiO 3 was systematically investigated as a photoanode candidate for solar water splitting. Dense bulk ceramics synthesized via solid‐state route retained the cubic perovskite structure. Rietveld refinement of the 5 mol% Sm‐doped SrTiO 3 (Sm:STO) sample confirmed successful A‐site substitution with Sm. Photoluminescence emission spectra revealed enhanced emission intensities upon doping, with concentration quenching observed at 5 mol% Sm. UV–Vis diffuse reflectance spectroscopy indicated only a marginal bandgap narrowing (3.18 for pure STO to 3.14 eV for 5% Sm:STO), suggesting that band structure modification alone does not account for the enhancement in the PEC performance. The 1.5% Sm:STO photoanode exhibited the highest photocurrent density of 64 µA cm − 2 at 1.23 V RHE , nearly two orders of magnitude higher than the undoped SrTiO 3 reference. This improvement is attributed to Sm induced grain refinement, increased electrochemically active surface area, and partially to oxygen‐vacancy formation. Mott–Schottky analysis confirmed n‐type conductivity, while chronoamperometry tests verified the material's chemical stability over 3 h under continuous illumination. These findings show that Sm doping could be used to activate bulk SrTiO 3 ceramics, demonstrating the potential of customized perovskites as scalable photoelectrodes for solar water splitting.
- Open Access
- 13 July 2026
- Published by Wiley in Zeitschrift für anorganische und allgemeine Chemie
- Vol. 652 (14) , e70185
Morphology and Photoelectrochemical Properties of Sputtered WO 3 :Mo Anodes
We present an investigation of sputtered WO 3 :Mo thin films as anodes for photoelectrochemical water splitting. The films were deposited by reactive sputtering from a W:Mo target ( w Mo = 10 at.%) on SnO 2 :F/glass with a systematic variation of the pressure p (0.40, 0.55, 0.70 Pa), the oxygen partial pressure p O2 (4–19 mPa), the substrate temperature T s (245, 280, 320 °C), the deposition rate r (0.6–7.8 nm min –1 ), and the thickness d (0.83–1.88 µm). For high T s , the layers consist of well‐defined crystals, whereas samples grown at a lower temperature show a high percentage of microcrystalline structures. The morphology correlates with the photocurrent density J , which is generally higher for crystalline layers. No correlations were found between J and p , p O2 , r , or d in the investigated parameter space. The highest measured J was 0.784 mA cm –2 at a potential of 1.23 V versus RHE.
- 13 July 2026
- Published by Wiley in Zeitschrift für anorganische und allgemeine Chemie
- Vol. 652 (14) , e70185
Open AccessMorphology and Photoelectrochemical Properties of Sputtered WO 3 :Mo Anodes
We present an investigation of sputtered WO 3 :Mo thin films as anodes for photoelectrochemical water splitting. The films were deposited by reactive sputtering from a W:Mo target ( w Mo = 10 at.%) on SnO 2 :F/glass with a systematic variation of the pressure p (0.40, 0.55, 0.70 Pa), the oxygen partial pressure p O2 (4–19 mPa), the substrate temperature T s (245, 280, 320 °C), the deposition rate r (0.6–7.8 nm min –1 ), and the thickness d (0.83–1.88 µm). For high T s , the layers consist of well‐defined crystals, whereas samples grown at a lower temperature show a high percentage of microcrystalline structures. The morphology correlates with the photocurrent density J , which is generally higher for crystalline layers. No correlations were found between J and p , p O2 , r , or d in the investigated parameter space. The highest measured J was 0.784 mA cm –2 at a potential of 1.23 V versus RHE.
- Open Access
- 14 July 2022
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 10 (32) , 11579-11587
Investigations on electron beam irradiated rare-earth doped SrF2 for application as low fading dosimeter material: evidence for and DFT simulation of a radiation-induced phase
A recent approach to measure electron radiation doses in the kGy range is the use of phosphors with an irradiation dose-dependent luminescence decay time. However, the applicability of the previously investigated material NaYF4:Yb3+,Er3+ is limited as it shows pronounced fading. Therefore, in this work, a modified SrF2 synthesis is presented that results in SrF2 nanoparticles codoped with Yb and either Er, Hm, or Tm. To assess their suitability as dosimeter material, dose response, as well as its degree of fading over 50 up to 140 days after irradiation were measured. Fading rates as small as 5% in SrF2:Er,Yb and 4% in SrF2:Ho,Yb were derived, which are comparable to established dosimeter materials. A combination of spectroscopy, diffraction and DFT calculations was used to elucidate the effect of irradiation, pointing towards the formation of a secondary phase of Yb2+ that we predict could be Yb2OF2. This irreversible formation of a secondary phase is considered to be the explanation for the low fading behavior in SrF2-based phosphors compared to NaYF4:Yb, Er, a highly attractive feature for electron beam dosimetry.
- 14 July 2022
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 10 (32) , 11579-11587
Open AccessInvestigations on electron beam irradiated rare-earth doped SrF2 for application as low fading dosimeter material: evidence for and DFT simulation of a radiation-induced phase
A recent approach to measure electron radiation doses in the kGy range is the use of phosphors with an irradiation dose-dependent luminescence decay time. However, the applicability of the previously investigated material NaYF4:Yb3+,Er3+ is limited as it shows pronounced fading. Therefore, in this work, a modified SrF2 synthesis is presented that results in SrF2 nanoparticles codoped with Yb and either Er, Hm, or Tm. To assess their suitability as dosimeter material, dose response, as well as its degree of fading over 50 up to 140 days after irradiation were measured. Fading rates as small as 5% in SrF2:Er,Yb and 4% in SrF2:Ho,Yb were derived, which are comparable to established dosimeter materials. A combination of spectroscopy, diffraction and DFT calculations was used to elucidate the effect of irradiation, pointing towards the formation of a secondary phase of Yb2+ that we predict could be Yb2OF2. This irreversible formation of a secondary phase is considered to be the explanation for the low fading behavior in SrF2-based phosphors compared to NaYF4:Yb, Er, a highly attractive feature for electron beam dosimetry.