Dillip Kumar Sahoo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Dillip Kumar Sahoo has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
Bhulok Sundar Mohanty
School of Mechanical Engineering, Sathyabama Institute of Science & Technology, Chennai, Tamil Nadu, India
3 shared publicationsG. B. Bhaskar
Department of Production Technology, MIT Campus, Anna University, Chennai, Tamil Nadu, India
2 shared publicationsSriram Prasath
School of Mechanical Engineering, Sathyabama Institute of science and Technology, Chennai, India
2 shared publicationsA. David Feby John
School of Mechanical Engg, Sathyabama Institute of Science & Technology, Chennai, TN, India
1 shared publicationA. Jaswanth
Sathyabama Institute of Science & Technology
1 shared publicationAmal M.V. Pradeep
School of Mechanical Engg, Sathyabama Institute of Science & Technology, Chennai, TN, India
1 shared publication
Latest Publications
- 25 October 2024
- Published by Springer Nature
- p. 189-195
Experimental Investigation of Salt Hydrate Phase-Change Material (Shape-Stabilized) Applied to a Solar Collector
- 25 October 2024
- Published by Springer Nature
- p. 189-195
Experimental Investigation of Salt Hydrate Phase-Change Material (Shape-Stabilized) Applied to a Solar Collector
- 4 December 2023
- Published by Taylor & Francis in International Journal of Ambient Energy
- Vol. 45 (1)
Modelling and simulation study on cooling system for proton exchange membrane fuel cell
- 4 December 2023
- Published by Taylor & Francis in International Journal of Ambient Energy
- Vol. 45 (1)
Modelling and simulation study on cooling system for proton exchange membrane fuel cell
- 28 November 2023
- Published by Springer Nature in Journal of The Institution of Engineers (India): Series D
- Vol. 106 (1) , 123-138
Predicting the Mechanical Characteristics of Friction Surfaced Aluminium Deposition Using RSM, ANN and PSO Optimization: A Comparative Evaluation
- 28 November 2023
- Published by Springer Nature in Journal of The Institution of Engineers (India): Series D
- Vol. 106 (1) , 123-138
Predicting the Mechanical Characteristics of Friction Surfaced Aluminium Deposition Using RSM, ANN and PSO Optimization: A Comparative Evaluation
- 18 May 2023
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 145 (8) , 1-12
Numerical Analysis of Spray Characteristics With Methane and Nanoparticles Under Various Injection Velocities
Utilization of numerical simulations has been increased rapidly to test many innovative concepts in the field of advanced fuel technologies. Implementation of chemical compound's interaction is viable option by numerical tools. Hence in this current study, the numerical simulation has been performed to evaluate the effect of spray velocities on the mass fraction of various compounds. The conceptual numerical domain has been constructed with mixture of two inlets such as air and CH4 using ansys-cfd. In addition to the CH4, the nanoparticles were injected in the same inlet using the volume of fluid method. The fuel was injected at different velocities varied from 100 m/s to 175 m/s, under the intervals of 25 m/s. Here two sections of the domains are created, one for the oxidizers and another for the CH4 with nanoparticles. Throughout the entire trial runs, the nanoparticle concentration has been maintained constant. A series of the pictorial contours have been captured to understand the influence of the fuel impinging characteristics and reaction rates in the combustion chamber. The results revealed that CH4 injection enhances the vortices formation inside the combustion chamber. Furthermore, turbulence intensity inside the chamber is high which delays the reaction time and leads to the higher combustion indeed.
- 18 May 2023
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 145 (8) , 1-12
Numerical Analysis of Spray Characteristics With Methane and Nanoparticles Under Various Injection Velocities
Utilization of numerical simulations has been increased rapidly to test many innovative concepts in the field of advanced fuel technologies. Implementation of chemical compound's interaction is viable option by numerical tools. Hence in this current study, the numerical simulation has been performed to evaluate the effect of spray velocities on the mass fraction of various compounds. The conceptual numerical domain has been constructed with mixture of two inlets such as air and CH4 using ansys-cfd. In addition to the CH4, the nanoparticles were injected in the same inlet using the volume of fluid method. The fuel was injected at different velocities varied from 100 m/s to 175 m/s, under the intervals of 25 m/s. Here two sections of the domains are created, one for the oxidizers and another for the CH4 with nanoparticles. Throughout the entire trial runs, the nanoparticle concentration has been maintained constant. A series of the pictorial contours have been captured to understand the influence of the fuel impinging characteristics and reaction rates in the combustion chamber. The results revealed that CH4 injection enhances the vortices formation inside the combustion chamber. Furthermore, turbulence intensity inside the chamber is high which delays the reaction time and leads to the higher combustion indeed.
- Open Access
- 1 January 2023
- Published by National Library of Serbia in Thermal Science
- Vol. 27 (5 Part A) , 3621-3634
Numerical investigation on cooling rate in proton exchange membrane fuel cell using propylene glycol fluid
In this study, a cooling channel was constructed inside the fuel cell to examine the impact of cooling on proton exchange membrane (PEM) fuel cell performance. The performance of the fuel cell was assessed using four different coolant mixtures: DI100 (100 percent Deionized water), PG10 (90 percent DI water + 10% Propylene Glycol), PG20 (80 percent DI Water + 20% Propylene Glycol), and PG30 (70 percent DI Water + 30% Propylene Glycol). The efficiency of the fuel cell, system temperature, operating parameters, coolant, and cooling channel shape of the fuel cell were tested using a computational fluid dynamics model based on the finite volume approach. The test results showed that the fuel cell performance was good for both single-cell fuel cells and fuel cell stacks at temperatures of 354 k and 360 k, respectively. However, as the membrane became dehydrated above 362 k for single cell fuel cells and after 371 k for fuel cell stacks, performance of the fuel cell decreased and no appreciable improvement was seen. For single cells, the fuel cell showed good performance improvement at PG30 combinations, whereas the best performance in stacks was attained at PG20 combinations.
- 1 January 2023
- Published by National Library of Serbia in Thermal Science
- Vol. 27 (5 Part A) , 3621-3634
Open AccessNumerical investigation on cooling rate in proton exchange membrane fuel cell using propylene glycol fluid
In this study, a cooling channel was constructed inside the fuel cell to examine the impact of cooling on proton exchange membrane (PEM) fuel cell performance. The performance of the fuel cell was assessed using four different coolant mixtures: DI100 (100 percent Deionized water), PG10 (90 percent DI water + 10% Propylene Glycol), PG20 (80 percent DI Water + 20% Propylene Glycol), and PG30 (70 percent DI Water + 30% Propylene Glycol). The efficiency of the fuel cell, system temperature, operating parameters, coolant, and cooling channel shape of the fuel cell were tested using a computational fluid dynamics model based on the finite volume approach. The test results showed that the fuel cell performance was good for both single-cell fuel cells and fuel cell stacks at temperatures of 354 k and 360 k, respectively. However, as the membrane became dehydrated above 362 k for single cell fuel cells and after 371 k for fuel cell stacks, performance of the fuel cell decreased and no appreciable improvement was seen. For single cells, the fuel cell showed good performance improvement at PG30 combinations, whereas the best performance in stacks was attained at PG20 combinations.
- 17 August 2022
- Published by World Scientific Pub Co Pte Ltd in Surface Review and Letters
- Vol. 29 (10)
A COMPARATIVE STUDY ON THE SINGLE AND DOUBLE-LAYERED DEPOSITION OF ALUMINUM 6063 OVER EN8 MEDIUM CARBON STEEL USING FRICTION SURFACING
This work estimates the optimum process parameters for the double-layer deposition of aluminum 6063 over EN8 medium carbon steel using friction surfacing. The control process parameters like axial force and feed rate of the consumable rod on two different deposition surface conditions, i.e. a good interface and a course interface during the process were investigated. The second layer deposition was performed over the roughness developed after the first layer deposition and contributed largely to the mechanical anchoring mechanism at the second coating interface. Assessment of the mechanical strength at the first coating interface (substrate/ coating 1) and second coating interface (coating 1/ coating 2) through bending and microhardness tests at both the interfaces was performed. The bending test results disclosed the existence of small delamination with no cracking at the second interface with a feed rate of 150[ ]mm/min at axial force of 5[ ]kN. An increase of 16.2% in the hardness value of consumable aluminum was seen at the first coating interface region. In contrast, the mean hardness at the second coating interface region was nearly the same as that of the consumable rod. Extensive studies of the surface coating and the microstructural features at both interfaces were performed through FESEM and EDAX analyses.
- 17 August 2022
- Published by World Scientific Pub Co Pte Ltd in Surface Review and Letters
- Vol. 29 (10)
A COMPARATIVE STUDY ON THE SINGLE AND DOUBLE-LAYERED DEPOSITION OF ALUMINUM 6063 OVER EN8 MEDIUM CARBON STEEL USING FRICTION SURFACING
This work estimates the optimum process parameters for the double-layer deposition of aluminum 6063 over EN8 medium carbon steel using friction surfacing. The control process parameters like axial force and feed rate of the consumable rod on two different deposition surface conditions, i.e. a good interface and a course interface during the process were investigated. The second layer deposition was performed over the roughness developed after the first layer deposition and contributed largely to the mechanical anchoring mechanism at the second coating interface. Assessment of the mechanical strength at the first coating interface (substrate/ coating 1) and second coating interface (coating 1/ coating 2) through bending and microhardness tests at both the interfaces was performed. The bending test results disclosed the existence of small delamination with no cracking at the second interface with a feed rate of 150[ ]mm/min at axial force of 5[ ]kN. An increase of 16.2% in the hardness value of consumable aluminum was seen at the first coating interface region. In contrast, the mean hardness at the second coating interface region was nearly the same as that of the consumable rod. Extensive studies of the surface coating and the microstructural features at both interfaces were performed through FESEM and EDAX analyses.
- Open Access
- 1 January 2022
- Published by IMR Press in Digest Journal of Nanomaterials and Biostructures
- Vol. 17 (1) , 263-284
Multi phase-field simulation study on microstructural grain development during inductive-based friction surfacing of aluminium
The computational solution is considered an effective tool for the analysis and a good understanding of the complex microstructural development that occurs during friction surfacing. In this article, ABACUS software was used to create a 3D-FE model of friction surfaced layering of AA 6063 aluminium on EN8 carbon steel, and the heat and strain rate collected throughout the operation were utilised for a computational investigation of microstructural recrystallization and grain development. The Multi-phase Field model (MFM) and constructive material model (CMM) were used for the prediction of the grain development during the process. A decrease in the incubation period from 0.839 sec to 0.578 sec was seen before recrystallization, after a temperature rises from 100°C to 300°C for substrate preheating. Validation of the reliability model obtained from the computational study was done using the image received from electron backscattered diffraction (EBSD) for grain size development and distribution. An appropriate assessment has been made between computational and experimental images which shows the maximum error of less than 10%. The development of grain structure during recrystallization was impacted extensively for increasing the coating strength, which was seen as inversely proportional to the average coating's grain diameter.
- 1 January 2022
- Published by IMR Press in Digest Journal of Nanomaterials and Biostructures
- Vol. 17 (1) , 263-284
Open AccessMulti phase-field simulation study on microstructural grain development during inductive-based friction surfacing of aluminium
The computational solution is considered an effective tool for the analysis and a good understanding of the complex microstructural development that occurs during friction surfacing. In this article, ABACUS software was used to create a 3D-FE model of friction surfaced layering of AA 6063 aluminium on EN8 carbon steel, and the heat and strain rate collected throughout the operation were utilised for a computational investigation of microstructural recrystallization and grain development. The Multi-phase Field model (MFM) and constructive material model (CMM) were used for the prediction of the grain development during the process. A decrease in the incubation period from 0.839 sec to 0.578 sec was seen before recrystallization, after a temperature rises from 100°C to 300°C for substrate preheating. Validation of the reliability model obtained from the computational study was done using the image received from electron backscattered diffraction (EBSD) for grain size development and distribution. An appropriate assessment has been made between computational and experimental images which shows the maximum error of less than 10%. The development of grain structure during recrystallization was impacted extensively for increasing the coating strength, which was seen as inversely proportional to the average coating's grain diameter.
- 31 October 2020
- Published by Springer Nature
- p. 161-175
Optimization and Characterization Study on Deposition of Aluminium 6063 Over IS 2062 Low Carbon Steel by Friction Surfacing
- 31 October 2020
- Published by Springer Nature
- p. 161-175
Optimization and Characterization Study on Deposition of Aluminium 6063 Over IS 2062 Low Carbon Steel by Friction Surfacing
- Open Access
- 12 April 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 40, S10-S18
An experimental study on friction surfaced coating of Aluminium 6063 over AISI 316 stainless steel substrate
- 12 April 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 40, S10-S18
Open AccessAn experimental study on friction surfaced coating of Aluminium 6063 over AISI 316 stainless steel substrate
- 19 May 2019
- Published by Taylor & Francis in International Journal of Ambient Energy
- Vol. 40 (4) , 361-366
Coupled CFD-FE analysis for the exhaust manifold to reduce stress of a direct injection-diesel engine
The present work deals with the investigation of the exhaust manifold of a four-cylinder diesel engine. Geometry creation and finite element method of the exhaust manifold was done using Computer Aided Design and CAE software. To simulate the thermal boundary coefficients of the exhaust manifold wall under steady-state loading conditions, the internal flow field structure was obtained using Computational Fluid Dynamics (CFD) software. The thermal boundary conditions were mapped to structural element surfaces of the exhaust manifold based on commercial finite element code ABAQUS. Thermal analysis was conducted to find out the high thermal stress areas. Design modifications were done on the high stress area and the process was repeated and stresses were reduced to meet the target. Numerical results and contour plots were reported on. The analysis of such a system is critical due to the complexity of meeting the structural and flow requirements. The use of coupled CFD and FEA simulation gives a better prediction of thermal stresses and flow behaviour in the exhaust manifold. The simulation captures the stress pattern and stress concentration at the failure location. The modification has reduced the stress level by 13% and eliminated the stress concentration.
- 19 May 2019
- Published by Taylor & Francis in International Journal of Ambient Energy
- Vol. 40 (4) , 361-366
Coupled CFD-FE analysis for the exhaust manifold to reduce stress of a direct injection-diesel engine
The present work deals with the investigation of the exhaust manifold of a four-cylinder diesel engine. Geometry creation and finite element method of the exhaust manifold was done using Computer Aided Design and CAE software. To simulate the thermal boundary coefficients of the exhaust manifold wall under steady-state loading conditions, the internal flow field structure was obtained using Computational Fluid Dynamics (CFD) software. The thermal boundary conditions were mapped to structural element surfaces of the exhaust manifold based on commercial finite element code ABAQUS. Thermal analysis was conducted to find out the high thermal stress areas. Design modifications were done on the high stress area and the process was repeated and stresses were reduced to meet the target. Numerical results and contour plots were reported on. The analysis of such a system is critical due to the complexity of meeting the structural and flow requirements. The use of coupled CFD and FEA simulation gives a better prediction of thermal stresses and flow behaviour in the exhaust manifold. The simulation captures the stress pattern and stress concentration at the failure location. The modification has reduced the stress level by 13% and eliminated the stress concentration.