Eva Birgit Møller
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Eva Birgit Møller has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Jørn Emil Gaarder
Department of Civil and Environmental Engineering, Norwegian University of Technology and Science (NTNU), 7030 Trondheim, Norway
1 shared publication - Naja Kastrup Friis
Department of Civil and Mechanical Engineering, Technical University of Denmark, Brovej 118, 2800 Lyngby, Denmark
1 shared publication Panagiota Pagoni
Technical University of Denmark, Brovej 118, 2800, Kgs. Lyngby, Denmark
1 shared publication- Tessa Kvist Hansen
Artelia A/S Rådgivende Ingeniører
1 shared publication
Latest Publications
- Open Access
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2948 (1) , 020047
Hygrothermal measurements in internally insulated solid masonry wall before and after hydrophobization
Constructions built between 1850 and 1960 comprise a remarkable percentage of the total European building stock and are from a time when there was very little f
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2948 (1) , 020047
Open AccessHygrothermal measurements in internally insulated solid masonry wall before and after hydrophobization
Constructions built between 1850 and 1960 comprise a remarkable percentage of the total European building stock and are from a time when there was very little f
- Open Access
A Tool for Calculating the Building Insulation Thickness for Lowest CO2 Emissions—A Greenlandic Example
Increased insulation reduces the energy needed during operations, but this may be less than the energy required for the extra insulation material. If so, there must be an optimal insulation thickness. This paper describes the development of a tool to determine the optimal insulation thickness, including what parameters are decisive, and presents some results along with a discussion of the success criteria and limitations. To make these considerations manageable for regular practitioners, only the transmission heat loss through walls is calculated. Although the tool is universal, Greenland is used as an example, because of its extreme climatic conditions. The tool includes climate change, 10 locations and 8 insulation materials. It focuses on greenhouse gas emissions, considers oil and district heating as heating sources, and evaluates four different climate change scenarios expressed in terms of heating degree days. The system is sensitive to insulation materials with high CO2 emissions and heating sources with high emission factors. This is also the case where climate change has the highest impact on the insulation thickness. Using the basic criterion, emitting a minimum of CO2-eq, the Insulation Thickness Optimizer (ITO), generally identifies higher insulation thicknesses as optimal than are currently seen in practice and in most building regulations.
Open AccessA Tool for Calculating the Building Insulation Thickness for Lowest CO2 Emissions—A Greenlandic Example
Increased insulation reduces the energy needed during operations, but this may be less than the energy required for the extra insulation material. If so, there must be an optimal insulation thickness. This paper describes the development of a tool to determine the optimal insulation thickness, including what parameters are decisive, and presents some results along with a discussion of the success criteria and limitations. To make these considerations manageable for regular practitioners, only the transmission heat loss through walls is calculated. Although the tool is universal, Greenland is used as an example, because of its extreme climatic conditions. The tool includes climate change, 10 locations and 8 insulation materials. It focuses on greenhouse gas emissions, considers oil and district heating as heating sources, and evaluates four different climate change scenarios expressed in terms of heating degree days. The system is sensitive to insulation materials with high CO2 emissions and heating sources with high emission factors. This is also the case where climate change has the highest impact on the insulation thickness. Using the basic criterion, emitting a minimum of CO2-eq, the Insulation Thickness Optimizer (ITO), generally identifies higher insulation thicknesses as optimal than are currently seen in practice and in most building regulations.