Hooman Gholamzadeh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Hooman Gholamzadeh has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
- Kevin Daub
Queen's University Kingston Ontario Canada
7 shared publications Kevin Daub
3 shared publications- Mark R. Daymond
Department of Mechanical and Materials Engineering Queen's University, Kingston Ontario Canada
3 shared publications S.Y. Persaud
3 shared publicationsSuraj Persaud
3 shared publicationsSuraj Y. Persaud
3 shared publications
Latest Publications
- Open Access
- 15 October 2026
- Published by Elsevier in SSRN Electronic Journal
Nanoscale Deformation and Chemistry of Pb-caustic Stress Corrosion Cracking in Alloy 800 at 305 °C
This study investigates the mechanism of stress corrosion cracking (SCC) in Alloy 800 after exposure to a 10 wt.% NaOH solution with 500 ppm Pb at 305 ºC. Post-exposure nanoscale chemical characterization of crack tips indicates the formation of successive areas of Ni enrichment due to selective dissolution (dealloying) of Fe ahead of the crack tip and along the crack path. Furthermore, Pb was observed at the interface of the metal and the Cr-rich oxide, likely impairing passivity to facilitate dealloying. Additionally, crack propagation was preferentially observed along {100} and {110} cleavage planes with local micro-steps along {111} planes. Increased deformation was observed in areas of crack arrest, while the density of geometrically necessary dislocations and misorientation along the fracture path was significantly lower. The combined chemistry and deformation observations suggest that the mechanism of SCC is consistent with a dealloying-assisted cleavage cracking mechanism.
- 15 October 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessNanoscale Deformation and Chemistry of Pb-caustic Stress Corrosion Cracking in Alloy 800 at 305 °C
This study investigates the mechanism of stress corrosion cracking (SCC) in Alloy 800 after exposure to a 10 wt.% NaOH solution with 500 ppm Pb at 305 ºC. Post-exposure nanoscale chemical characterization of crack tips indicates the formation of successive areas of Ni enrichment due to selective dissolution (dealloying) of Fe ahead of the crack tip and along the crack path. Furthermore, Pb was observed at the interface of the metal and the Cr-rich oxide, likely impairing passivity to facilitate dealloying. Additionally, crack propagation was preferentially observed along {100} and {110} cleavage planes with local micro-steps along {111} planes. Increased deformation was observed in areas of crack arrest, while the density of geometrically necessary dislocations and misorientation along the fracture path was significantly lower. The combined chemistry and deformation observations suggest that the mechanism of SCC is consistent with a dealloying-assisted cleavage cracking mechanism.
- Open Access
- 17 September 2026
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 173 (18) , 181501
The Effect of Pb-Underpotential Deposition on the Dealloying of Alloy 800 in a Near-Boiling Caustic Environment
This study investigates the influence of Pb-underpotential deposition (Pb-UPD) on the dealloying of Fe–Cr–Ni alloys in a near-boiling conditions (50 wt. % NaOH environment, where the formation of a stable Cr-rich oxide is not thermodynamically favored). SCC testing and electrochemical measurements on Alloy 800 (Fe-32Ni-21Cr) were performed to assess the influence of Pb on dealloying. Post-exposure X-ray photoelectron spectroscopy (XPS) indicated that the Pb is present as Pb(II) at the top surface and, more importantly, deposits as metallic Pb at the metal-film interface. Electrochemical measurements revealed that the addition of Pb shifted the corrosion potential of Alloy 800 toward more positive values and suppressed the dealloying peak. The results were accompanied by lower crack density and shorter crack length compared to Pb-free conditions. The combined electrochemical and XPS results are consistent with the established Pb-underpotential deposition (Pb-UPD) on the metallic surface, where adsorbed Pb substantially suppresses the anodic dissolution of Fe and Cr by blocking active dissolution sites. The present results demonstrate that Pb-UPD can also reduce the susceptibility to dealloying and SCC initiation on a bare metal surface in the absence of passivity.
- 17 September 2026
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 173 (18) , 181501
Open AccessThe Effect of Pb-Underpotential Deposition on the Dealloying of Alloy 800 in a Near-Boiling Caustic Environment
This study investigates the influence of Pb-underpotential deposition (Pb-UPD) on the dealloying of Fe–Cr–Ni alloys in a near-boiling conditions (50 wt. % NaOH environment, where the formation of a stable Cr-rich oxide is not thermodynamically favored). SCC testing and electrochemical measurements on Alloy 800 (Fe-32Ni-21Cr) were performed to assess the influence of Pb on dealloying. Post-exposure X-ray photoelectron spectroscopy (XPS) indicated that the Pb is present as Pb(II) at the top surface and, more importantly, deposits as metallic Pb at the metal-film interface. Electrochemical measurements revealed that the addition of Pb shifted the corrosion potential of Alloy 800 toward more positive values and suppressed the dealloying peak. The results were accompanied by lower crack density and shorter crack length compared to Pb-free conditions. The combined electrochemical and XPS results are consistent with the established Pb-underpotential deposition (Pb-UPD) on the metallic surface, where adsorbed Pb substantially suppresses the anodic dissolution of Fe and Cr by blocking active dissolution sites. The present results demonstrate that Pb-UPD can also reduce the susceptibility to dealloying and SCC initiation on a bare metal surface in the absence of passivity.
- Open Access
- 9 September 2026
- Published by Elsevier in SSRN Electronic Journal
Nanoscale Mechanistic Insights into the Pit-to-Crack Transition for Alloy 800 in Acidic Sulfate Media at 280 °C
The mechanisms associated with the pit-to-crack (P2C) transition in Alloy 800 were investigated in mildly acidic sulfate conditions (0.55 M [SO42-], pH280°C 4.0). Comparative analysis of U-shaped and semi-elliptical pit geometries reveals increased plastic strain accumulation, facilitating the initiation and growth of longer cracks in the semi-elliptical geometry. Nanoscale characterization of the U-shaped P2C geometry revealed that sulfur adsorbed near the oxide metal interface within the crack and near the crack tip, suppressing repassivation. Kernel average misorientation (KAM) and geometrically necessary dislocation (GND) analyses of the U-shaped pit geometry identified a zone of elevated plastic deformation adjacent to the crack initiation site, together with dislocation pile-ups at twin boundaries, indicating that localized strain develops before cracks can propagate further. The combined deformation and chemistry characterization support a stress corrosion cracking mechanism in which repeated cycles of strain induced passive film rupture followed by sulfur assisted anodic dissolution drive crack initiation and propagation.
- 9 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessNanoscale Mechanistic Insights into the Pit-to-Crack Transition for Alloy 800 in Acidic Sulfate Media at 280 °C
The mechanisms associated with the pit-to-crack (P2C) transition in Alloy 800 were investigated in mildly acidic sulfate conditions (0.55 M [SO42-], pH280°C 4.0). Comparative analysis of U-shaped and semi-elliptical pit geometries reveals increased plastic strain accumulation, facilitating the initiation and growth of longer cracks in the semi-elliptical geometry. Nanoscale characterization of the U-shaped P2C geometry revealed that sulfur adsorbed near the oxide metal interface within the crack and near the crack tip, suppressing repassivation. Kernel average misorientation (KAM) and geometrically necessary dislocation (GND) analyses of the U-shaped pit geometry identified a zone of elevated plastic deformation adjacent to the crack initiation site, together with dislocation pile-ups at twin boundaries, indicating that localized strain develops before cracks can propagate further. The combined deformation and chemistry characterization support a stress corrosion cracking mechanism in which repeated cycles of strain induced passive film rupture followed by sulfur assisted anodic dissolution drive crack initiation and propagation.
- Open Access
- 14 May 2026
- Published by Elsevier in SSRN Electronic Journal
The effect of cold rolling on the microstructure and corrosion behaviour of Alloy 800 in molten chloride salt mixture
This study investigates the influence of cold rolling (0%, 10%, 20% and 35%) on the corrosion behavior of Alloy 800 (Fe–31Ni–21Cr) in a LiCl–KCl–MgCl2 eutectic mixture at 750 °C for 12 h under Ar–1% O2. Microstructural evolution and corrosion morphology were characterized using SEM, EDS, and EBSD analyses. Cold rolling altered the dominant corrosion mechanism from localized grain boundary attack with deep penetration in the as-received condition to a more uniform corrosion mode with reduced penetration depth. EBSD results indicated increased stored deformation energy in cold-rolled samples, while post-exposure observations revealed recovery and partial recrystallization at 750 °C. The elevated defect density and rapid microstructural evolution enhanced elemental diffusion, promoting more homogeneous dealloying compared to the non-deformed alloy. These findings demonstrate that cold rolling significantly modifies both the microstructural response and corrosion mechanism of Alloy 800 in molten chloride environments.
- 14 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessThe effect of cold rolling on the microstructure and corrosion behaviour of Alloy 800 in molten chloride salt mixture
This study investigates the influence of cold rolling (0%, 10%, 20% and 35%) on the corrosion behavior of Alloy 800 (Fe–31Ni–21Cr) in a LiCl–KCl–MgCl2 eutectic mixture at 750 °C for 12 h under Ar–1% O2. Microstructural evolution and corrosion morphology were characterized using SEM, EDS, and EBSD analyses. Cold rolling altered the dominant corrosion mechanism from localized grain boundary attack with deep penetration in the as-received condition to a more uniform corrosion mode with reduced penetration depth. EBSD results indicated increased stored deformation energy in cold-rolled samples, while post-exposure observations revealed recovery and partial recrystallization at 750 °C. The elevated defect density and rapid microstructural evolution enhanced elemental diffusion, promoting more homogeneous dealloying compared to the non-deformed alloy. These findings demonstrate that cold rolling significantly modifies both the microstructural response and corrosion mechanism of Alloy 800 in molten chloride environments.
- Open Access
- 27 February 2026
- Published by Elsevier in Corrosion Science
- Vol. 264
High-temperature aqueous corrosion of Alloy 400: Influence of pH and dissolved oxygen
- 27 February 2026
- Published by Elsevier in Corrosion Science
- Vol. 264
Open AccessHigh-temperature aqueous corrosion of Alloy 400: Influence of pH and dissolved oxygen
- Open Access
- 13 January 2026
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1053
Additive manufacturing–induced microstructural hierarchy alters dealloying behavior in CoCrFeMnNi high-entropy alloy
- 13 January 2026
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1053
Open AccessAdditive manufacturing–induced microstructural hierarchy alters dealloying behavior in CoCrFeMnNi high-entropy alloy
- Open Access
- 25 November 2025
- Published by Elsevier in Corrosion Science
- Vol. 259
Oxygen-accelerated corrosion of Alloy 800 in a molten LiCl-KCl-MgCl2 eutectic mixture
- 25 November 2025
- Published by Elsevier in Corrosion Science
- Vol. 259
Open AccessOxygen-accelerated corrosion of Alloy 800 in a molten LiCl-KCl-MgCl2 eutectic mixture
- Open Access
- 30 November 2024
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 605
The effect of proton irradiation on dealloying of Alloy 800 in an aqueous environment
- 30 November 2024
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 605
Open AccessThe effect of proton irradiation on dealloying of Alloy 800 in an aqueous environment
- 27 August 2023
- Published by Elsevier in Acta Materialia
- Vol. 260
Characterization of dealloying and associated stress corrosion cracking: The effect of crystallographic orientation
- 27 August 2023
- Published by Elsevier in Acta Materialia
- Vol. 260
Characterization of dealloying and associated stress corrosion cracking: The effect of crystallographic orientation
- 20 May 2023
- Published by Elsevier in Corrosion Science
- Vol. 220
A mechanistic study on dealloying-induced stress corrosion cracking of Alloy 800 in boiling caustic solutions
- 20 May 2023
- Published by Elsevier in Corrosion Science
- Vol. 220
A mechanistic study on dealloying-induced stress corrosion cracking of Alloy 800 in boiling caustic solutions