Christian Hofmann
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Christian Hofmann has a total of 86 co-authors. Here are the top co-authors by number of shared publications:
Maik Wiemer
Fraunhofer ENAS,Chemnitz,Germany
12 shared publicationsMario Baum
Fraunhofer Institute for Electronic, Nano Systems ENAS,Department Systems Engineering,Chemnitz,Germany
8 shared publicationsMartin Kroll
Institute for Machine Tools and Production Processes, University of Technology,Chemnitz,Germany,09126
8 shared publicationsHarald Kuhn
Fraunhofer ENAS,Chemnitz,Germany
7 shared publicationsKlaus Vogel
System Packaging Fraunhofer Institute for Electronic Nano Systems,Chemnitz,Germany
7 shared publications- Martin Kroll
University of Technology
5 shared publications
Latest Publications
- Open Access
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 62 (10) , 7503805
Investigation of Standing Wave Phenomena in Electromagnetic Radio Frequency Heating of Aluminum Frames for Wafer-Level Thermo-Compression Bonding
This study investigates the influence of electromagnetic (EM) standing wave effects on the temperature distribution in bond structures during medium- to very-high-frequency (MF–VHF) induction heating for wafer-level thermo-compression bonding (TCB). Aluminum bond frames were patterned on a 6-inch borosilicate glass wafer and subjected to EM excitation at frequencies of 2 MHz, 13.56 MHz, 40 MHz, and 70 MHz. A custom-designed induction coil was developed using an iterative simulation approach to achieve uniform wafer-level heating at 2 MHz. To analyze the standing wave phenomenon, coupled EM-thermal finite element (FE) simulations were performed to study heating and temperature distributions, followed by experimental validation using dedicated MF–VHF induction heating setups. For the experimentally validated setup within this study, standing wave behavior was observed to get pronounced at 13.56 MHz, intensifying at higher frequencies. This leads to non-uniform EM field distributions and irregular heating patterns across the wafer, which poses a significant challenge to achieving homogeneous temperature profiles. The results highlight the need for optimized coil designs for reliable wafer-level packaging, and present concepts for their compensation including coil splitting, multi-frequency excitation, and standing wave compensation via radio frequency (RF) switches.
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 62 (10) , 7503805
Open AccessInvestigation of Standing Wave Phenomena in Electromagnetic Radio Frequency Heating of Aluminum Frames for Wafer-Level Thermo-Compression Bonding
This study investigates the influence of electromagnetic (EM) standing wave effects on the temperature distribution in bond structures during medium- to very-high-frequency (MF–VHF) induction heating for wafer-level thermo-compression bonding (TCB). Aluminum bond frames were patterned on a 6-inch borosilicate glass wafer and subjected to EM excitation at frequencies of 2 MHz, 13.56 MHz, 40 MHz, and 70 MHz. A custom-designed induction coil was developed using an iterative simulation approach to achieve uniform wafer-level heating at 2 MHz. To analyze the standing wave phenomenon, coupled EM-thermal finite element (FE) simulations were performed to study heating and temperature distributions, followed by experimental validation using dedicated MF–VHF induction heating setups. For the experimentally validated setup within this study, standing wave behavior was observed to get pronounced at 13.56 MHz, intensifying at higher frequencies. This leads to non-uniform EM field distributions and irregular heating patterns across the wafer, which poses a significant challenge to achieving homogeneous temperature profiles. The results highlight the need for optimized coil designs for reliable wafer-level packaging, and present concepts for their compensation including coil splitting, multi-frequency excitation, and standing wave compensation via radio frequency (RF) switches.
- 19 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-11
Design, Structural Characterization, and Superconducting Behavior of Niobium Thin-Film Microstructures for Ion-Trap Quantum Computers: Toward J–B–T Critical Surface Mapping for Cryogenic 3D SiP Integration
Superconducting thin-film microstructures are promising for generating local magnetic-field gradients for individual ion addressing in trapped-ion quantum processors while minimizing Joule heating at cryogenic temperatures. In this work, sputtered niobium (Nb) thin films on Si were patterned into coil and meander structures as candidate components for cryogenic 3D microsystem integration. The films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), Raman spectroscopy, and electrical resistance at cryogenic temperature. XRD confirms textured bcc Nb with a dominant Nb (110) reflection and an apparent out-of-plane coherence length of ~20 nm. SEM reveals a porous, needle-like nanograin morphology, while Raman spectroscopy indicates a disordered mixed niobium-oxide surface layer. Electrical measurements show clear superconducting transitions, with midpoint critical temperatures of about 7.5 K for the coil and 7.8 K for the meander, both below bulk Nb. The normal-state behavior is characterized by low residual-resistivity ratios (RRR), indicating significant disorder and grain-boundary scattering. Based on the measured Tc values and geometry-derived effective current densities (Jc), a phenomenological J – B –T critical-surface model was constructed to estimate the superconducting operating window under simultaneous temperature and magnetic-field loading. The results establish a process – structure – property correlation for sputtered Nb on Si and provide guidance for integrating superconducting thin-film coils into future trapped-ion cryogenic microsystems.
- 19 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-11
Design, Structural Characterization, and Superconducting Behavior of Niobium Thin-Film Microstructures for Ion-Trap Quantum Computers: Toward J–B–T Critical Surface Mapping for Cryogenic 3D SiP Integration
Superconducting thin-film microstructures are promising for generating local magnetic-field gradients for individual ion addressing in trapped-ion quantum processors while minimizing Joule heating at cryogenic temperatures. In this work, sputtered niobium (Nb) thin films on Si were patterned into coil and meander structures as candidate components for cryogenic 3D microsystem integration. The films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), Raman spectroscopy, and electrical resistance at cryogenic temperature. XRD confirms textured bcc Nb with a dominant Nb (110) reflection and an apparent out-of-plane coherence length of ~20 nm. SEM reveals a porous, needle-like nanograin morphology, while Raman spectroscopy indicates a disordered mixed niobium-oxide surface layer. Electrical measurements show clear superconducting transitions, with midpoint critical temperatures of about 7.5 K for the coil and 7.8 K for the meander, both below bulk Nb. The normal-state behavior is characterized by low residual-resistivity ratios (RRR), indicating significant disorder and grain-boundary scattering. Based on the measured Tc values and geometry-derived effective current densities (Jc), a phenomenological J – B –T critical-surface model was constructed to estimate the superconducting operating window under simultaneous temperature and magnetic-field loading. The results establish a process – structure – property correlation for sputtered Nb on Si and provide guidance for integrating superconducting thin-film coils into future trapped-ion cryogenic microsystems.
- 19 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-8
Advanced 3D Modeling of Reactive Multilayer Systems for Chip- and Wafer-Level Bonding Applications
Selective bonding technologies, particularly those utilizing self-propagating exothermic reactions, enable the joining of heterogeneous substrates at chip and wafer level without subjecting sensitive components to global thermal loading. This work presents a comprehensive numerical design approach for reactive bonding that couples the integrated reactive material system (iRMS) with the bond substrates and interface metallization. The developed finite element (FE) model was calibrated using comprehensive experimental characterization: high-speed imaging was employed to determine the reaction propagation kinetics, while differential scanning calorimetry (DSC) is utilized to quantify the specific reaction enthalpy. These empirical inputs were used to perform a transient thermal analysis in ANSYS, simulating the bonding process for intermetallic Pd/Al system and oxide based CuO/Al system. The model was validated against bonding experiments using composite Si/SiO2 and glass substrates, demonstrating its ability in predicting the thermal process window and optimizing the bond interface design.
- 19 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-8
Advanced 3D Modeling of Reactive Multilayer Systems for Chip- and Wafer-Level Bonding Applications
Selective bonding technologies, particularly those utilizing self-propagating exothermic reactions, enable the joining of heterogeneous substrates at chip and wafer level without subjecting sensitive components to global thermal loading. This work presents a comprehensive numerical design approach for reactive bonding that couples the integrated reactive material system (iRMS) with the bond substrates and interface metallization. The developed finite element (FE) model was calibrated using comprehensive experimental characterization: high-speed imaging was employed to determine the reaction propagation kinetics, while differential scanning calorimetry (DSC) is utilized to quantify the specific reaction enthalpy. These empirical inputs were used to perform a transient thermal analysis in ANSYS, simulating the bonding process for intermetallic Pd/Al system and oxide based CuO/Al system. The model was validated against bonding experiments using composite Si/SiO2 and glass substrates, demonstrating its ability in predicting the thermal process window and optimizing the bond interface design.
- 2 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Novel Ultrasonic Flip Chip Bonding Approach Utilizing Electroplated Aluminium Pillars for Advanced Packaging
Ultrasonic Flip-Chip bonding (US-FCB) is a potential integration method for narrow pitch ranges (less than $100 \mu \mathrm{m})$ [1], enabling the integration flexibility of individual chips into a package. A mono-metallic interconnect is more reliable and involves fewer fabrication process steps compared to solder reflow. The US-FCB was primarily investigated for metals such as gold (Au) and Copper (Cu) due to their material reliability, superior conductivity and technology availability [2]. However, both Au and Cu present integration challenges that often require additional metallization layers and elevated bonding temperatures [3], [4]. A new alternative approach is the use of aluminium (AI), offering mono-metallic interconnection at temperatures below $50{ }^{\circ} \mathrm{C}$ [5], [6]. The enabling technology for Al US-FCB is the electrochemical deposition (ECD) of Al from ionic liquids at the wafer level [6], [7]. Utilizing the same pillar fabrication method as for Cu or Au, the same benefits in geometric flexibility and thickness variation can be achieved. In comparison to Cu or Au, the use of Al as an interconnection material in US-FCB reduces the need for additional metallization layers on microelectronic contact pads.- 2 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Novel Ultrasonic Flip Chip Bonding Approach Utilizing Electroplated Aluminium Pillars for Advanced Packaging
Ultrasonic Flip-Chip bonding (US-FCB) is a potential integration method for narrow pitch ranges (less than $100 \mu \mathrm{m})$ [1], enabling the integration flexibility of individual chips into a package. A mono-metallic interconnect is more reliable and involves fewer fabrication process steps compared to solder reflow. The US-FCB was primarily investigated for metals such as gold (Au) and Copper (Cu) due to their material reliability, superior conductivity and technology availability [2]. However, both Au and Cu present integration challenges that often require additional metallization layers and elevated bonding temperatures [3], [4]. A new alternative approach is the use of aluminium (AI), offering mono-metallic interconnection at temperatures below $50{ }^{\circ} \mathrm{C}$ [5], [6]. The enabling technology for Al US-FCB is the electrochemical deposition (ECD) of Al from ionic liquids at the wafer level [6], [7]. Utilizing the same pillar fabrication method as for Cu or Au, the same benefits in geometric flexibility and thickness variation can be achieved. In comparison to Cu or Au, the use of Al as an interconnection material in US-FCB reduces the need for additional metallization layers on microelectronic contact pads.- 22 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Finite Element Modeling and Experimental Validation of Induction Heating for Efficient TLP Bonding with Cu-Sn Layers
This study investigates the use of high-frequency induction heating for transient liquid phase (TLP) bonding of Cu-Sn layers, offering a rapid and selective process for MEMS packaging. Finite element simulations are carried out in parallel with experiments to model the coupled electromagnetic and thermal behavior, with a focus on the frequency-dependent skin effect. Two modeling strategies are evaluated: one resolves the skin depth volumetrically while capturing all conductor losses, and the other uses a simplified boundary conditions to reduce computational cost. Both approaches show error of less than 3% with respect to experimental results. The findings indicate that a minimum frequency of 40.7 MHz and a current of 12 A are required to reach the threshold temperature of 250 °C, at which Cu-Sn intermetallic compounds (IMCs) begin to form. Additionally, heating rates of up to $\mathbf{2 0 0 ~ K} / \mathbf{s}$ can be achieved at $\mathbf{5 5 ~ M H z}$.- 22 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Finite Element Modeling and Experimental Validation of Induction Heating for Efficient TLP Bonding with Cu-Sn Layers
This study investigates the use of high-frequency induction heating for transient liquid phase (TLP) bonding of Cu-Sn layers, offering a rapid and selective process for MEMS packaging. Finite element simulations are carried out in parallel with experiments to model the coupled electromagnetic and thermal behavior, with a focus on the frequency-dependent skin effect. Two modeling strategies are evaluated: one resolves the skin depth volumetrically while capturing all conductor losses, and the other uses a simplified boundary conditions to reduce computational cost. Both approaches show error of less than 3% with respect to experimental results. The findings indicate that a minimum frequency of 40.7 MHz and a current of 12 A are required to reach the threshold temperature of 250 °C, at which Cu-Sn intermetallic compounds (IMCs) begin to form. Additionally, heating rates of up to $\mathbf{2 0 0 ~ K} / \mathbf{s}$ can be achieved at $\mathbf{5 5 ~ M H z}$.- 11 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 117, 1-5
Aluminum-Aluminum Wafer Level Thermo Compression Bonding Using Thick Electroplated Aluminum Bonding Frames
Wafer bonding is crucial in semiconductor manufacturing, integrating diverse materials and creating complex devices. Aluminum thermo-compression bonding (Al TCB) is promising for its high bond strength, easy integrability into production process chains, and reliability, essential for advanced packaging and MEMS. This study investigates thick (>4 μm) electroplated aluminum layers, both as-deposited and planarized, under varying conditions. As-deposited surfaces with asperities show high dicing yields above 90 % and strong shear strengths above 40 N/mm 2 , while planarized surfaces require higher temperatures to achieve comparable shear strength. The findings emphasize the role of surface roughness on bond quality and provide insights for optimizing Al TCB processes in semiconductor manufacturing.
- 11 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 117, 1-5
Aluminum-Aluminum Wafer Level Thermo Compression Bonding Using Thick Electroplated Aluminum Bonding Frames
Wafer bonding is crucial in semiconductor manufacturing, integrating diverse materials and creating complex devices. Aluminum thermo-compression bonding (Al TCB) is promising for its high bond strength, easy integrability into production process chains, and reliability, essential for advanced packaging and MEMS. This study investigates thick (>4 μm) electroplated aluminum layers, both as-deposited and planarized, under varying conditions. As-deposited surfaces with asperities show high dicing yields above 90 % and strong shear strengths above 40 N/mm 2 , while planarized surfaces require higher temperatures to achieve comparable shear strength. The findings emphasize the role of surface roughness on bond quality and provide insights for optimizing Al TCB processes in semiconductor manufacturing.
- 15 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 137-140
Inductive Sintering Module for Improved Multi-Die Attach in the Field of Power Packaging
This work presents a heating technology for multi-die attach based on inductive silver sintering. Thus, the heat for the sintering reaction is confined locally to the bond region, avoiding heating of the entire power module.
- 15 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 137-140
Inductive Sintering Module for Improved Multi-Die Attach in the Field of Power Packaging
This work presents a heating technology for multi-die attach based on inductive silver sintering. Thus, the heat for the sintering reaction is confined locally to the bond region, avoiding heating of the entire power module.
- Open Access
- 27 July 2023
- Published by MDPI AG in Electronics
- Vol. 12 (15) , 3247
Inductive Sintering of Silver Micro Particles for Bonding of Microelectronic Components
In this article, an efficient die-bonding technology based on silver sintering due to induction heating is presented. By using this technology, the heat for the sintering reaction is locally limited to the bonding area and heating of the entire power module is avoided. Furthermore, the sintering reaction is promoted due to current flow between the silver particles, and the sintering time is drastically reduced. Next to the experimental trials presented in this paper, finite element (FE) simulation methods were applied to develop a suitable induction coil geometry for the bonding of a diode to a direct bonded copper (DBC) substrate. Additional heating and sintering tests verified the reliability of the simulation model as well as the technological approach. Diodes were successfully bonded during the experiments and were analyzed by means of scanning electron microscopy (SEM) and function tests to qualify the inductive bonding technology. The results presented in this paper demonstrate that induction heating has high potential for cost-effective production in the field of die attach and can drastically increase the output in power-electronics production.
- 27 July 2023
- Published by MDPI AG in Electronics
- Vol. 12 (15) , 3247
Open AccessInductive Sintering of Silver Micro Particles for Bonding of Microelectronic Components
In this article, an efficient die-bonding technology based on silver sintering due to induction heating is presented. By using this technology, the heat for the sintering reaction is locally limited to the bonding area and heating of the entire power module is avoided. Furthermore, the sintering reaction is promoted due to current flow between the silver particles, and the sintering time is drastically reduced. Next to the experimental trials presented in this paper, finite element (FE) simulation methods were applied to develop a suitable induction coil geometry for the bonding of a diode to a direct bonded copper (DBC) substrate. Additional heating and sintering tests verified the reliability of the simulation model as well as the technological approach. Diodes were successfully bonded during the experiments and were analyzed by means of scanning electron microscopy (SEM) and function tests to qualify the inductive bonding technology. The results presented in this paper demonstrate that induction heating has high potential for cost-effective production in the field of die attach and can drastically increase the output in power-electronics production.
- Open Access
- 26 June 2023
- Published by MDPI AG in Preprints.org
Inductive Sintering of Silver Micro Particles for Bonding of Microelectronic Components
In this article, an efficient die bonding technology based on silver sintering due to induction heating is presented. By using this technology, the heat for the sintering reaction is locally limited to the bonding area and the heating of the entire power module is avoided. Furthermore, the sintering reaction is promoted due to current flow between the silver particles and the sintering time is drastically reduced. Next to the experimental trials presented in this paper, FE-simulation methods were applied in order to develop a suitable induction coil geometry for the bonding of a diode to a direct bonded copper (DBC) substrate. Additional heating and sintering tests verified the reliability of the simulation model as well as the technological approach. Diodes were successfully bonded during the experiments and were analyzed by means of scanning electron microscopy (SEM) and function tests in order to qualify the inductive bonding technology. The results presented in this paper demonstrate, that induction heating has high potential for cost effective production in the field of die-attach and can drastically increase the output in power electronics production.
- 26 June 2023
- Published by MDPI AG in Preprints.org
Open AccessInductive Sintering of Silver Micro Particles for Bonding of Microelectronic Components
In this article, an efficient die bonding technology based on silver sintering due to induction heating is presented. By using this technology, the heat for the sintering reaction is locally limited to the bonding area and the heating of the entire power module is avoided. Furthermore, the sintering reaction is promoted due to current flow between the silver particles and the sintering time is drastically reduced. Next to the experimental trials presented in this paper, FE-simulation methods were applied in order to develop a suitable induction coil geometry for the bonding of a diode to a direct bonded copper (DBC) substrate. Additional heating and sintering tests verified the reliability of the simulation model as well as the technological approach. Diodes were successfully bonded during the experiments and were analyzed by means of scanning electron microscopy (SEM) and function tests in order to qualify the inductive bonding technology. The results presented in this paper demonstrate, that induction heating has high potential for cost effective production in the field of die-attach and can drastically increase the output in power electronics production.