Jong Bong Nah
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Jong Bong Nah has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Anindya Nath
Global Foundries Inc., 1000 River St, Essex Junction, VT 05452, USA
1 shared publication - Anthony Boyd
U.S. Naval Research Laboratory, 4555 Overlook Ave. SW, Washington, DC 20375, USA
1 shared publication - David Kurt Gaskill
Institute for Research in Electronics and Applied Physics
1 shared publication Dongkoo Kang
Frank Reidy Research Center for Bioelectrics, Old Dominion University, Norfolk, VA, USA
1 shared publication- Evgeniya H. Lock
Plasma Physics Division, Naval Research Laboratory, Washington, DC, USA
1 shared publication - Frank Keith Perkins
U.S. Naval Research Laboratory, 4555 Overlook Ave. SW, Washington, DC 20375, USA
1 shared publication
Latest Publications
- Open Access
Electrical and Low Frequency Noise Characterization of Graphene Chemical Sensor Devices Having Different Geometries
Chemiresistive graphene sensors are promising for chemical sensing applications due to their simple device structure, high sensitivity, potential for miniaturization, low-cost, and fast response. In this work, we investigate the effect of (1) ZnO nanoparticle functionalization and (2) engineered defects onto graphene sensing channel on device resistance and low frequency electrical noise. The engineered defects of interest include 2D patterns of squares, stars, and circles and 1D patterns of slots parallel and transverse to the applied electric potential. The goal of this work is to determine which devices are best suited for chemical sensing applications. We find that, relative to pristine graphene devices, nanoparticle functionalization leads to reduced contact resistance but increased sheet resistance. In addition, functionalization lowers 1/f current noise on all but the uniform mesa device and the two devices with graphene strips parallel to carrier transport. The strongest correlations between noise and engineering defects, where normalized noise amplitude as a function of frequency f is described by a model of AN/fγ, are that γ increases with graphene area and contact area but decreases with device total perimeter, including internal features. We did not find evidence of a correlation between the scalar amplitude, AN, and the device channel geometries. In general, for a given device area, the least noise was observed on the least-etched device. These results will lead to an understanding of what features are needed to obtain the optimal device resistance and how to reduce the 1/f noise which will lead to improved sensor performance.
Open AccessElectrical and Low Frequency Noise Characterization of Graphene Chemical Sensor Devices Having Different Geometries
Chemiresistive graphene sensors are promising for chemical sensing applications due to their simple device structure, high sensitivity, potential for miniaturization, low-cost, and fast response. In this work, we investigate the effect of (1) ZnO nanoparticle functionalization and (2) engineered defects onto graphene sensing channel on device resistance and low frequency electrical noise. The engineered defects of interest include 2D patterns of squares, stars, and circles and 1D patterns of slots parallel and transverse to the applied electric potential. The goal of this work is to determine which devices are best suited for chemical sensing applications. We find that, relative to pristine graphene devices, nanoparticle functionalization leads to reduced contact resistance but increased sheet resistance. In addition, functionalization lowers 1/f current noise on all but the uniform mesa device and the two devices with graphene strips parallel to carrier transport. The strongest correlations between noise and engineering defects, where normalized noise amplitude as a function of frequency f is described by a model of AN/fγ, are that γ increases with graphene area and contact area but decreases with device total perimeter, including internal features. We did not find evidence of a correlation between the scalar amplitude, AN, and the device channel geometries. In general, for a given device area, the least noise was observed on the least-etched device. These results will lead to an understanding of what features are needed to obtain the optimal device resistance and how to reduce the 1/f noise which will lead to improved sensor performance.
- 5 August 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 42 (10) , 3231-3238
Shock Wave Generation in Water for Biological Studies
We have used a pulsed power generator based on stacking MOSFET switches to create breakdown in water and generate shock waves. The pulses with an exponential decay have a maximum voltage of 4 kV. With the pulse application of approximately 50 μs, the breakdown voltage is approximately 3 kV. Post-breakdown events, such as shock wave emission and bubble expansion and collapse were recorded by a fast camera. The shock speed was recorded as 1.5 km/s and the maximum bubble diameter is 2.3 mm. This shock wave generator can be used on the microscope and provides a means of studying the shock impact on biological cells.
- 5 August 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 42 (10) , 3231-3238
Shock Wave Generation in Water for Biological Studies
We have used a pulsed power generator based on stacking MOSFET switches to create breakdown in water and generate shock waves. The pulses with an exponential decay have a maximum voltage of 4 kV. With the pulse application of approximately 50 μs, the breakdown voltage is approximately 3 kV. Post-breakdown events, such as shock wave emission and bubble expansion and collapse were recorded by a fast camera. The shock speed was recorded as 1.5 km/s and the maximum bubble diameter is 2.3 mm. This shock wave generator can be used on the microscope and provides a means of studying the shock impact on biological cells.