SVSreenath Mylo Valappil

Sreenath Mylo Valappil

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Sreenath Mylo Valappil has a total of 33 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Annealing-Induced Multiphase Evolution and Photocatalytic Performance of TiO2-ZnO Nanocomposites with Varying Zn Concentrations

    by Muhammed Shajin J.S, Sankar S, Lini Jose, Sajith S.V, Itsuki Misono, Sreenath Mylo Valappil, Tsuyoshi Yoshitake, Nissamudeen K.M

    TiO2-ZnO nanocomposites with varying Zn precursor concentrations were synthesized by the co-precipitation method and annealed at subsequent temperatures. The effects of Zn concentration and annealing temperature on the structural, morphological and optical properties were systematically investigated. XRD and Raman analyses indicated that anatase TiO2 remained the major phase at 500 and 600° C, further annealing resulted in rutile phase dominated TiO2 with prominent ZnTiO3 formation. FESEM, TEM, HRTEM and SAED analyses supported the structural evolution and multiphase structure. Optical studies showed that apparent band gap, Urbach energy values and photoluminescence (PL) were influenced by annealing temperatures. Composites with anatase dominant showed excellent photocatalytic degradation of methylene blue (95.31-97.12%) under UV irradiation, in contrast, catalytic efficiency considerably decreased in rutile dominated samples. Kinetic analysis also revealed faster degradation rates for anatase rich samples. Reusability studies showed that both composites retained their phase structure after four photocatalytic cycles. Also, the 1.0 M composite showed relatively smaller loss in photocatalytic activity than 0.5 M composite. Hydroxyl radicals and superoxide radicals are the primary reactive species followed by photogenerated holes involved in the photocatalytic activity was further identified by the scavenger experiments. These findings demonstrate that high photocatalytic activity can be achieved over a broad processing window of 0.5 M and 1.0 M Zn concentration and 500-600° C annealing temperature.

  • Effect of annealing temperature on phase evolution and photocatalytic reaction kinetics of ZnO-TiO2 nanocomposites

    by J.S. Muhammed Shajin, S. Sankar, Lini Jose, K.M. Nissamudeen, Itsuki Misono, Sreenath Mylo Valappil, Tsuyoshi Yoshitake

  • Multifunctional rare-earth-doped BaCeO3 phosphors via facile combustion: Tunable emission for advanced optoelectronics

    by S.V. Jasira, A.M. Huda Thasneem, C.K. Shilpa, Annmary Augustine, Sreenath Mylo Valappil, Tsuyoshi Yoshitake, K.M. Nissamudeen


  • Open Access

    Heteroepitaxial Growth of β ‐Ga 2 O 3 on Diamond (111) via Radio Frequency Magnetron Sputtering: Mechanistic Insights from Scanning/Transmission Electron Microscopy

    by Itsuki Misono, Sho Nekita, Hongye Gao, Sreenath Mylo Valappil, Yixin Wang, Yuto Ikegami, Yuki Katamune, Hiroshi Naragino, Phongsaphak Sittimart, Shinya Ohmagari, et al.

    This study delves into the comprehensive microstructural analysis of heteroepitaxial β ‐Ga 2 O 3 thin films grown on single‐crystal diamond (111) wafers by radio frequency magnetron sputtering. The heterostructure is probed through a scanning/transmission electron microscope and succeeded in direct observation of β ‐Ga 2 O 3 ||diamond [10] and β ‐Ga 2 O 3 ||diamond [10] heteroepitaxial interfaces, which up to now have only has been inferred through indirect analyzing methods based on X‐ray diffraction. Fast Fourier Transformation (FFT) patterns of corresponding oriented interfaces exhibited virtual overlapping for the substrate and the epilayer, authenticating the robust epitaxial arrangement. Furthermore, this study elucidates the discrete growth modes of β ‐Ga 2 O 3 and domains arising from the asymmetric hexagonal C─O lattice matching, through 4D‐STEM analysis and subsequent virtual dark‐field image reconstruction. Strategies for the improvement of crystallinity, surface morphology, and facile thickness controllability of the β‐Ga 2 O 3 epilayer through optimizing the RF power, facilitating a low re‐evaporation rate of the film, are discussed. This finding underscores the importance of domain control in the improved epitaxial quality of β ‐Ga 2 O 3 that can inform the development of budget‐friendly and scalable β ‐Ga 2 O 3 /diamond heterostructures for advanced functional devices.


  • Harsh Environment‐Immune All‐Carbon Visible Light Photodetector: Sensitivity Improvement by Nitrogen‐Vacancy Center Density Enhancement Through Electron Irradiation

    by Sreenath Mylo Valappil, Taisuke Kageura, Shinya Ohmagari, Shinobu Onoda, Phongsaphak Sittimart, Hiroshi Naragino, Tsuyoshi Yoshitake

    A novel all‐carbon visible light detector is fabricated on a nitrogen‐doped (N‐doped) single‐crystalline diamond (SCD) with interdigitated nanocarbon ohmic contacts. It has been posited that the formation of nitrogen‐vacancy (NV) centers within the photoabsorption layer serves as an effective strategy to augment the device's detection capabilities. To illustrate the significance of this enhancement, NV density is manipulated and augmented by electron beam irradiation in a moderately N‐doped diamond. Despite the incompetent nitrogen doping, the enhancement of NV density in the diamond active layer has resulted in a substantial enhancement of nearly 1.5 orders of magnitude for several critical detection parameters. The NV‐enabled all‐carbon detector demonstrates a high degree of tolerance toward thermal and corrosive environments. The dark current is maintained at a level below 0.01 pA even when the device is operated at a temperature of 250 °C. The robust interfacial bonding between the diamond and the nanocarbon‐interdigitated electrodes ensures that the device exhibits no physical or performance deterioration when subjected to highly corrosive environments. The results of this study may provide insights that can inform the development of high‐sensitivity, harsh environment immune diamond visible light detectors benefiting from the multiple photon excitation of NV quantum centers.


  • Maximizing visible Raman resolution of nanodiamond grains fabricated by coaxial arc plasma deposition through oxygen plasma etching optimization

    by Sreenath Mylo Valappil, Abdelrahman Zkria, Phongsaphak Sittimart, Shinya Ohmagari, Tsuyoshi Yoshitake

    Among the nondestructive carbon material characterization tools, the prominence of visible Raman spectroscopy has surged remarkably for many years due to its ability to explore a diverse array of carbon bonding configurations. However, to fully unlock the distinctive features concealed within carbon composite materials, additional specimen treatments or precise spectroscope calibrations are necessary. In the same regard, the tiny diamond grain size (5–10 nm) and the pronounced amount of sp 2 carbon in the ultrananocrystalline diamond film represent major challenges in visible light excitation. In this work, we employ calibrated oxygen plasma reactive ion etching conditions to manifest the nanodiamond visible Raman signature from ultrananocrystalline diamond/amorphous carbon composite (UNCD/a‐C) films fabricated by coaxial arc plasma deposition. Upon plasma etching, the broad defect band in the visible Raman spectra converged toward the diamond characteristic Raman peak at 1332 cm −1 . A detailed explanation of band components of the Raman spectra is extracted through peak fitting procedures. The results of Raman spectroscopy are further correlated with the electrical characteristics of the nitrogen‐doped UNCD/a‐C films due to the optimized oxygen plasma etching processes.


  • Open Access

    Heteroepitaxial growth of β-Ga2O3 thin films on single crystalline diamond (111) substrates by radio frequency magnetron sputtering

    by Takafumi Kusaba, Phongsaphak Sittimart, Yuki Katamune, Taisuke Kageura, Hiroshi Naragino, Shinya Ohmagari, Sreenath Mylo Valappil, Satoki Nagano, Abdelrahman Zkria, Tsuyoshi Yoshitake

    In this work, we demonstrate the first achievement in heteroepitaxial growth of β-Ga2O3 thin films on single crystalline diamond (111) wafers using RF magnetron sputtering. A single monoclinic (β-phase) structure with a monofamily { 2 ¯ 01} plane was obtained. XRD pole figure shows ( 2 ̅ 02) and (002) textures of the ( 2 ̅ 01) β-Ga2O3 plane parallel to (111) diamond with six distinct rotational domains, confirming successful epitaxial growth. Collectively, this research provides valuable insights into the epitaxial growth of β-Ga2O3 on diamond via sputtering, paving the way for scalable β-Ga2O3/diamond heterostructures for future electronic and optoelectronic applications with not only high performance but also effective self-thermal management.


  • Corrosion‐Resistive and Low Specific Contact Resistance Ohmic Contacts to Semiconducting Diamonds Using Nanocarbon Electrodes

    by Sreenath Mylo Valappil, Abdelrahman Zkria, Shinya Ohmagari, Hiroshi Naragino, Hiromitsu Kato, Tsuyoshi Yoshitake

    The realization of diamond‐based advanced devices is interrelated with the fabrication of practical ohmic contacts. Contrary to boron‐doped, the phosphorus‐doped diamonds with interface carbide forming Ti‐based conventional ohmic contacts find their limitation in device fabrication due to the high contact resistance. Herein, nanocarbon ohmic contacts are deposited by a coaxial arc plasma gun on semiconducting diamonds, and their composite structure which facilitates exceptional contact properties is explored. A comparative electrical characterization between nanocarbon ohmic contacts and conventional Ti‐based contacts is performed on a heavily phosphorus‐doped diamond, and they exhibited one‐order declination in specific contact resistance. In addition to the low contact resistance, an ideal ohmic electrode is preferable to have good mechanical adhesion and corrosion resistance for device applications. The contact behavior of n‐type diamond/nanocarbon against an extremely corrosive environment realized by boiling H2SO4 + HNO3solution is analyzed. The nanocarbon ohmic contacts exhibit excellent corrosion resistance and mechanical adhesion over conventional Ti‐based contacts. A similar trend is also observed for nanocarbon contacts on boron‐doped diamonds. The modest effect on the transfer length of the nanocarbon contacts with respect to acid treatment sessions indicates a tightly bonded diamond/nanocarbon interface and actively suggests their application in highly‐corrosive and harsh environments.


  • Open Access

    Overcoming the impact of post-annealing on uniformity of diamond (100) Schottky barrier diodes through corrosion-resistant nanocarbon ohmic contacts

    by Sreenath Mylo Valappil, Abdelrahman Zkria, Shinya Ohmagari, Tsuyoshi Yoshitake

    Diamond-based Schottky barrier diodes (SBDs) are involved in many technological applications. In a conventional SBD fabrication process that involves interface carbide forming ohmic contacts, a post-annealing step is necessary for ohmic contacts to achieve their operational efficiency. However, this step deteriorates the essential oxygen coverage at the diamond surface which in turn affects SBDs uniformity. So, an additional oxygen termination step is necessary prior to Schottky metal deposition. In this study, a non-conventional fabrication method is introduced using corrosion-resistant nanocarbon ohmic contacts fabricated by coaxial arc plasma deposition. As a result, The SBD parameters including ideality factors and barrier heights exhibited high uniformity with a very small standard deviation for the proposed fabrication process flow when compared with process flow including a post-annealing step. Furthermore, the contact behavior of nanocarbon ohmic electrodes is investigated on a heavily boron-doped diamond film using circular transmission line model theory and a specific contact resistance of ∼10−5 Ωcm2 is obtained, suggesting the practical application of nanocarbon ohmic contacts for diamond-based electronic devices.


  • Open Access

    Nanocarbon ohmic electrodes fabricated by coaxial arc plasma deposition for phosphorus-doped diamond electronics application

    by Sreenath Mylo Valappil, Shinya Ohmagari, Abdelrahman Zkria, Phongsaphak Sittimart, Eslam Abubakr, Hiromitsu Kato, Tsuyoshi Yoshitake

    N-Type (phosphorus-doped) diamond is a promising material for diamond-based electronic devices. However, realizing good ohmic contacts for phosphorus-doped diamonds limits their applications. Thus, the search for non-conventional ohmic contacts has become a hot topic for many researchers. In this work, nanocarbon ohmic electrodes with enhanced carrier collection efficiency were deposited by coaxial arc plasma deposition. The fabricated nanocarbon ohmic electrodes were extensively examined in terms of specific contact resistance and corrosion resistance. The circular transmission line model theory was used to estimate the charge collection efficiency of the nanocarbon ohmic electrodes in terms of specific contact resistance at a specific voltage range (5–10 V); they exhibited a specific contact resistance of 1 × 10−3 Ωcm2. The result revealed one order reduction in the specific contact resistance and, consequently, a potential drop at the diamond/electrode interface compared to the conventional Ti electrodes. Moreover, the fabricated nanocarbon electrodes exhibited high mechanical adhesion and chemical inertness over repeated acid treatments. In device applications, the nanocarbon electrodes were evaluated for Ni/n-type diamond Schottky diodes, and they exhibited nearly one order enhancement in the rectification ratio and a fast charge collection at lower biasing voltages.