Yegireddi Shireesha
Yegireddi Shireesha has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
- Bade Venkata Suresh
GMR Institute of Technology (Deemed to be University), Andhra Pradesh, India
4 shared publications - Matta Vykunta Rao
GMR Institute of Technology
3 shared publications - Annepu Lakshumu Naidu
Department of Mechanical Engineering, GMR Institute of Technology Deemed to be University, Rajam, India
2 shared publications - Bappa Mondal
GMR Institute of Technology (GMRIT)—Deemed to be University
2 shared publications - Chilamkurti Lakshmi Venkata Ranga Sobhanachala Vara Prasad
GMR Institute of Technology
2 shared publications - Chiranjeeva Rao Seela
Department of Mechanical Engineering GMR Institute of Technology (GMRIT) - Deemed to be University Rajam Andhra Pradesh India gmrit.edu.in
2 shared publications
Latest Publications
- 19 June 2026
- Published by Springer Nature in Emergent Materials
- Vol. 9 (7) , 151
Development of surface layers in Al 2024 via accumulative roll bonding and correlation of microstructural evolution with damping behavior
- 19 June 2026
- Published by Springer Nature in Emergent Materials
- Vol. 9 (7) , 151
Development of surface layers in Al 2024 via accumulative roll bonding and correlation of microstructural evolution with damping behavior
- 27 December 2024
- Published by Springer Nature in Journal of Formative Design in Learning
- Vol. 8 (2) , 113-128
Formative Learning Through a Spatial Visualization-Based Cadathon Contest
- 27 December 2024
- Published by Springer Nature in Journal of Formative Design in Learning
- Vol. 8 (2) , 113-128
Formative Learning Through a Spatial Visualization-Based Cadathon Contest
- 22 November 2024
- Published by Springer Nature in Applied Physics A
- Vol. 130 (12) , 1-10
Study on the structure, DC electrical resistivity and magnetic properties of Co0.7Cu0.2Zn0.1Fe2-xCrxO4 nano ferrites
- 22 November 2024
- Published by Springer Nature in Applied Physics A
- Vol. 130 (12) , 1-10
Study on the structure, DC electrical resistivity and magnetic properties of Co0.7Cu0.2Zn0.1Fe2-xCrxO4 nano ferrites
- 6 December 2023
- Published by Springer Nature in Journal of Formative Design in Learning
- Vol. 7 (2) , 139-157
Bridging the Industry–Academia Gap: An Experiential Learning for Engineering Students
- 6 December 2023
- Published by Springer Nature in Journal of Formative Design in Learning
- Vol. 7 (2) , 139-157
Bridging the Industry–Academia Gap: An Experiential Learning for Engineering Students
- 6 October 2022
- Published by Springer Nature
- p. 633-644
Influence of Mechanical Vibrations on Impact Strength of 1018 Mild Steel Butt-Weld-Joints
- 6 October 2022
- Published by Springer Nature
- p. 633-644
Influence of Mechanical Vibrations on Impact Strength of 1018 Mild Steel Butt-Weld-Joints
- Open Access
- 10 August 2022
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2022, 1-10
Influence of Nano Boric Acid Material in Bio-Diesel Blends to Enhance the Surface Quality with Minimum Quality Lubrication
Machining with conventional process of lubrication is a general industrial practice for diminishing cutting forces, high temperature, and friction. During the machining process, cutting fluid characteristics plays a crucial role in enhancing machining performance when it is properly chosen. The harmful gases during machining process are often hazardous to individuals and the environment. It is also economically unviable if the cutting fluid cost, method of application, and flow rate is underestimated. Due to chip obstruction and poor absorption, a high amount of heat is liberated and as a result high quantity and high quality of lubricant or coolant are need to be supplied between the chip-tool interfaces consistently. This process becomes costly and degrades the environment. In the current work, nano powder of boric acid is chosen as solid type lubricant in turning process, which is blended with bio-diesel consisting of coconut oil as base oil. The outcomes of nano powder mixed bio-diesel cutting fluids exhibited significant enhancement in machining characteristics when it is compared with wet and dry machining. And also, Taguchi method of orthogonal representation is considered to determine the optimum weight percentage of the bio-diesel blends at different conditions of the machining process. The optimum machining conditions were obtained at high machining operation with a feed of 0.04 mm/min, speed of 600 rpm, and toll diameter of 0.5 mm.
- 10 August 2022
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2022, 1-10
Open AccessInfluence of Nano Boric Acid Material in Bio-Diesel Blends to Enhance the Surface Quality with Minimum Quality Lubrication
Machining with conventional process of lubrication is a general industrial practice for diminishing cutting forces, high temperature, and friction. During the machining process, cutting fluid characteristics plays a crucial role in enhancing machining performance when it is properly chosen. The harmful gases during machining process are often hazardous to individuals and the environment. It is also economically unviable if the cutting fluid cost, method of application, and flow rate is underestimated. Due to chip obstruction and poor absorption, a high amount of heat is liberated and as a result high quantity and high quality of lubricant or coolant are need to be supplied between the chip-tool interfaces consistently. This process becomes costly and degrades the environment. In the current work, nano powder of boric acid is chosen as solid type lubricant in turning process, which is blended with bio-diesel consisting of coconut oil as base oil. The outcomes of nano powder mixed bio-diesel cutting fluids exhibited significant enhancement in machining characteristics when it is compared with wet and dry machining. And also, Taguchi method of orthogonal representation is considered to determine the optimum weight percentage of the bio-diesel blends at different conditions of the machining process. The optimum machining conditions were obtained at high machining operation with a feed of 0.04 mm/min, speed of 600 rpm, and toll diameter of 0.5 mm.
- 1 January 2022
- Published by Springer Nature
- p. 493-502
Experimental Study on Tensile Behavior of Tri-axial Hybrid Fiber Composites
- 1 January 2022
- Published by Springer Nature
- p. 493-502
Experimental Study on Tensile Behavior of Tri-axial Hybrid Fiber Composites