Adrian Amler
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Adrian Amler has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Martin März
Institute for Power Electronics, Friedrich-Alexander-Universität Erlangen-Nürnberg (FAU), 90429 Nuremberg, Germany
3 shared publications Lukas Best
Institute of Power Electronics at Friedrich-Alexander-Universitt Erlangen-Nrnberg, Nrnberg, Germany
1 shared publication- Nikolai Weitz
Institute of Power Electronics, Friedrich-Alexander-University, Nuremberg, Germany
1 shared publication - Thomas Lehmeier
Institute of Power Electronics, Friedrich-Alexander-Universitt Erlangen-Nrnberg, Nrnberg, Germany
1 shared publication - Yan Zhou
Institute of Power Electronics, Friedrich-Alexander-Universitt Erlangen-Nrnberg, Nrnberg, Germany
1 shared publication
Latest Publications
- Open Access
- 31 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 6, 1910-1922
Capacitive Power Transfer as Scalable Low-Cost Multi-Load Auxiliary Power Supply for Gate Drivers
Using operating frequencies in the RF range around the 13.56 MHz ISM band, Capacitive Power Transfer (CPT) can provide sufficient power for a wide range of applications even across coupling capacitances of only a few pF. A low power, multi-load power supply can be realized with simple inductorless capacitive links and rectifiers. Multiple loads connect in parallel to a common primary transmission line, driven by a resonant inverter. This scalable low-cost isolating converter can be used in power electronic converters and inverters to simultaneously supply multiple gate drivers with auxiliary power. However, this application presents some unique challenges – in particular, the extremely low coupling capacitances required to limit common-mode interference – which are investigated in this article. It is shown that gate drivers for GaN eHEMTs can be supplied with 35 mW at 5 V using an effective capacitance of only 0.7 pF, and SiC-MOSFETs and even Si-IGBTs can be driven at frequencies in the 10-100's kHz range. Burst tests confirm common-mode immunity even under voltage slopes exceeding 400 V/ns between loads and to ground.
- 31 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 6, 1910-1922
Open AccessCapacitive Power Transfer as Scalable Low-Cost Multi-Load Auxiliary Power Supply for Gate Drivers
Using operating frequencies in the RF range around the 13.56 MHz ISM band, Capacitive Power Transfer (CPT) can provide sufficient power for a wide range of applications even across coupling capacitances of only a few pF. A low power, multi-load power supply can be realized with simple inductorless capacitive links and rectifiers. Multiple loads connect in parallel to a common primary transmission line, driven by a resonant inverter. This scalable low-cost isolating converter can be used in power electronic converters and inverters to simultaneously supply multiple gate drivers with auxiliary power. However, this application presents some unique challenges – in particular, the extremely low coupling capacitances required to limit common-mode interference – which are investigated in this article. It is shown that gate drivers for GaN eHEMTs can be supplied with 35 mW at 5 V using an effective capacitance of only 0.7 pF, and SiC-MOSFETs and even Si-IGBTs can be driven at frequencies in the 10-100's kHz range. Burst tests confirm common-mode immunity even under voltage slopes exceeding 400 V/ns between loads and to ground.
- Open Access
- 16 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (2) , 2505-2521
Three-Phase ARCP Inverter Using Soft-Switching With a Single Shared Inductor
Soft-switching in power inverters for drive and grid applications can both enhance the efficiency by reducing switching losses and improve electromagnetic interference (EMI) due to lower switching speeds with their associated $\mathrm{d}v/\mathrm{d}t$ . An advantageous topology is the well-known auxiliary resonant commutated pole (ARCP) inverter. The development of such power electronic inverters often focuses on reducing weight, volume, and cost. Considering a three-phase ARCP system, this article presents a novel single shared inductor $(\mathrm{S}^{2}\mathrm{I})$ -ARCP approach to reduce the passive component count in the auxiliary circuit from three to one. The simultaneous use of the shared inductor by more than one phase must be detected and avoided by the control algorithm. A frequency analysis of such occurrences is performed, and a method for avoiding them by shifting the switching edges is presented. The proposed $\mathrm{S}^{2}\mathrm{I}$ -ARCP topology together with an appropriate control algorithm is implemented and validated at 10 kW with an 800 V dc-link. Efficiency measurement results indicated a significant loss reduction under soft-switching operation by more than 38% compared with hard-switching, with a peak efficiency value of 99.58%. It is demonstrated that a mere adjustment in the control signal generation can save two resonant inductors without significant disadvantages.
- 16 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (2) , 2505-2521
Open AccessThree-Phase ARCP Inverter Using Soft-Switching With a Single Shared Inductor
Soft-switching in power inverters for drive and grid applications can both enhance the efficiency by reducing switching losses and improve electromagnetic interference (EMI) due to lower switching speeds with their associated $\mathrm{d}v/\mathrm{d}t$ . An advantageous topology is the well-known auxiliary resonant commutated pole (ARCP) inverter. The development of such power electronic inverters often focuses on reducing weight, volume, and cost. Considering a three-phase ARCP system, this article presents a novel single shared inductor $(\mathrm{S}^{2}\mathrm{I})$ -ARCP approach to reduce the passive component count in the auxiliary circuit from three to one. The simultaneous use of the shared inductor by more than one phase must be detected and avoided by the control algorithm. A frequency analysis of such occurrences is performed, and a method for avoiding them by shifting the switching edges is presented. The proposed $\mathrm{S}^{2}\mathrm{I}$ -ARCP topology together with an appropriate control algorithm is implemented and validated at 10 kW with an 800 V dc-link. Efficiency measurement results indicated a significant loss reduction under soft-switching operation by more than 38% compared with hard-switching, with a peak efficiency value of 99.58%. It is demonstrated that a mere adjustment in the control signal generation can save two resonant inductors without significant disadvantages.
- Open Access
- 11 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 10 (6) , 7808-7823
Improved Capacitive Power Transfer With Non-Resonant Power Transfer Link Using Radio Frequency Push-Pull Inverter
In recent years, research on Wireless Power Transfer and Switched-Mode Power Supplies with a capacitive coupling link has been on the rise. Whereas many researchers investigate resonant coupling links, often resulting in tough requirements for the involved inductors, this paper focuses on the elimination of all inductive components in the coupling link and the rectifier through the use of a non-resonant capacitive link. We propose a converter with a resonant single-ended push-pull inverter operating at radio frequencies of e.g. 13.56 MHz to directly drive the non-resonant capacitive power transfer link. The ability of the converter to operate at a high frequency and to facilitate a significant voltage change across the link capacitors improves the power transfer characteristics of the system compared to previously published systems with a non-resonant capacitive link. Said combination is also beneficial for the transient behavior, parameter variation robustness, an easy design process, simplified drive requirements, and a predictable and limited capacitor voltage stress. The presented converter transmits 122.9 W across an effective link capacitance of 120 pF, leading to the highest input voltage-normalized power transfer to link capacitance value of 13.7 W/(nF∙V) among previously published capacitive power transfer systems with a non-resonant link.
- 11 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 10 (6) , 7808-7823
Open AccessImproved Capacitive Power Transfer With Non-Resonant Power Transfer Link Using Radio Frequency Push-Pull Inverter
In recent years, research on Wireless Power Transfer and Switched-Mode Power Supplies with a capacitive coupling link has been on the rise. Whereas many researchers investigate resonant coupling links, often resulting in tough requirements for the involved inductors, this paper focuses on the elimination of all inductive components in the coupling link and the rectifier through the use of a non-resonant capacitive link. We propose a converter with a resonant single-ended push-pull inverter operating at radio frequencies of e.g. 13.56 MHz to directly drive the non-resonant capacitive power transfer link. The ability of the converter to operate at a high frequency and to facilitate a significant voltage change across the link capacitors improves the power transfer characteristics of the system compared to previously published systems with a non-resonant capacitive link. Said combination is also beneficial for the transient behavior, parameter variation robustness, an easy design process, simplified drive requirements, and a predictable and limited capacitor voltage stress. The presented converter transmits 122.9 W across an effective link capacitance of 120 pF, leading to the highest input voltage-normalized power transfer to link capacitance value of 13.7 W/(nF∙V) among previously published capacitive power transfer systems with a non-resonant link.