Chunyin Shen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Chunyin Shen has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
Gance Dai
State Key Laboratory of Chemical Engineering East China University of Science and Technology (ECUST) Shanghai China
5 shared publicationsXun Fang
East China University of Science and Technology
3 shared publicationsYanli Wang
State Key Laboratory of Chemical Engineering East China University of Science and Technology (ECUST) Shanghai China
2 shared publicationsBei Wang
State Key Laboratory of Chemical Engineering East China University of Science and Technology (ECUST) Shanghai China
1 shared publicationCaiyun Lu
State Key Laboratory of Chemical Engineering East China University of Science and Technology (ECUST) Shanghai China
1 shared publicationDong Zhao
State Key Laboratory of Chemical Engineering East China University of Science and Technology (ECUST) Shanghai China
1 shared publication
Latest Publications
- 19 July 2023
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 140 (37)
Effect of air gap induction on the morphological microstructure of polyether sulfone hollow fiber membrane
Polyether sulfone hollow fiber membrane was prepared via nonsolvent‐induced phase separation process using dimethylacetamide (DMAc) as a solvent, Polyvinylpyrrolidone (PVP‐K30) and water as additives. The mechanism of air gap environment in the membrane structure formation was studied. The scanning electron microscope microstructure morphology revealed that the air gap environment induced the microstructure formation of membranes. The low humidity air gap environment was not conducive to the surface pore formation and hard to obtain surface pores until lowering the dope solution temperature. The high humidity can easily induce the formation of large out surface pore structure along with the decreases of the surface pore uniformity. As air gap humidity and distance increased, the membrane cross section structure near the outer surface tends to be looser and that near the inner surface became denser, while the proportion of finger‐like pores in the cross section initially increased and stabilized. At 100 RH, the average outer surface pore size increased from 0.192 μm at an air gap distance of 20 cm to 0.351 μm at 50 cm, the corresponding pore density decreased from 2.66 to 1.13 pores/μm2, and the percentage of the inner skin layer thickness increased from 3.26% to 7.69%.
- 19 July 2023
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 140 (37)
Effect of air gap induction on the morphological microstructure of polyether sulfone hollow fiber membrane
Polyether sulfone hollow fiber membrane was prepared via nonsolvent‐induced phase separation process using dimethylacetamide (DMAc) as a solvent, Polyvinylpyrrolidone (PVP‐K30) and water as additives. The mechanism of air gap environment in the membrane structure formation was studied. The scanning electron microscope microstructure morphology revealed that the air gap environment induced the microstructure formation of membranes. The low humidity air gap environment was not conducive to the surface pore formation and hard to obtain surface pores until lowering the dope solution temperature. The high humidity can easily induce the formation of large out surface pore structure along with the decreases of the surface pore uniformity. As air gap humidity and distance increased, the membrane cross section structure near the outer surface tends to be looser and that near the inner surface became denser, while the proportion of finger‐like pores in the cross section initially increased and stabilized. At 100 RH, the average outer surface pore size increased from 0.192 μm at an air gap distance of 20 cm to 0.351 μm at 50 cm, the corresponding pore density decreased from 2.66 to 1.13 pores/μm2, and the percentage of the inner skin layer thickness increased from 3.26% to 7.69%.
- 8 August 2022
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 139 (38)
Rheological behavior of PES/PVP/DMAc solution and PVP structural regulation for hollow fiber membrane
Rheological study plays a significant role in hollow fiber membrane spinning process and membrane structure regulation. In this work, the rheological behaviors of polyethersulfone (PES) spinning solutions added the polyvinylpyrrolidone (grade of PVP‐K30, PVP‐K60, and PVP‐K90) were systematically investigated by rotational rheometry to understand how the PES membrane structure changes. Results show that PVP of variable molecular weights change the rheological properties of PES spinning solution, such as the viscosity (ηa), non‐Newtonian index (n), flow activation energy (Eη), structural viscosity index (∆η), storage modulus (G′), and loss modulus (G′′). The mixture with PVP‐K30 exhibits optimal spinnability but the finger‐like membrane structure is undesirable for the hemodialysis. The rheological behaviors of PES/PVP‐K60 and PES/PVP‐K90 reveal that increasing shear rate and temperature are effective ways to improve the spinnability of the mixture and the membrane structure is regulated. Meanwhile, the addition of PVP‐K60 or PVP‐K90 at their critical concentration to the PES solution can fabricate a hollow membrane with a sponge‐like structure. Combining spinnability and membrane structure, PVP‐K90 is a suitable additive for the hemodialysis membrane.
- 8 August 2022
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 139 (38)
Rheological behavior of PES/PVP/DMAc solution and PVP structural regulation for hollow fiber membrane
Rheological study plays a significant role in hollow fiber membrane spinning process and membrane structure regulation. In this work, the rheological behaviors of polyethersulfone (PES) spinning solutions added the polyvinylpyrrolidone (grade of PVP‐K30, PVP‐K60, and PVP‐K90) were systematically investigated by rotational rheometry to understand how the PES membrane structure changes. Results show that PVP of variable molecular weights change the rheological properties of PES spinning solution, such as the viscosity (ηa), non‐Newtonian index (n), flow activation energy (Eη), structural viscosity index (∆η), storage modulus (G′), and loss modulus (G′′). The mixture with PVP‐K30 exhibits optimal spinnability but the finger‐like membrane structure is undesirable for the hemodialysis. The rheological behaviors of PES/PVP‐K60 and PES/PVP‐K90 reveal that increasing shear rate and temperature are effective ways to improve the spinnability of the mixture and the membrane structure is regulated. Meanwhile, the addition of PVP‐K60 or PVP‐K90 at their critical concentration to the PES solution can fabricate a hollow membrane with a sponge‐like structure. Combining spinnability and membrane structure, PVP‐K90 is a suitable additive for the hemodialysis membrane.
- 28 February 2017
- Published by Springer Nature in Fibers and Polymers
- Vol. 18 (2) , 303-312
Comparative investigation of molded thickness and surface density on the structures and mechanical properties of lightweight reinforced thermoplastic composites
- 28 February 2017
- Published by Springer Nature in Fibers and Polymers
- Vol. 18 (2) , 303-312
Comparative investigation of molded thickness and surface density on the structures and mechanical properties of lightweight reinforced thermoplastic composites
- 9 August 2016
- Published by Wiley in Polymer Composites
- Vol. 39 (7) , 2212-2223
The influence of compatibilizers on the structure and mechanical properties of lightweight reinforced thermoplastics
Lightweight reinforced thermoplastics (LWRT) have a low density and high rigidity. The application of LWRTs to automotive interiors, such as headliners and instrument panels, is very promising. The porous structure of LWRTs is formed in the process of deconsolidation, so pores may appear between the matrix and fibers that interrupt the transfer of stress and deteriorate the mechanical properties. In this article, maleic anhydride‐grafted polypropylene (PP‐g‐MAH) and glycidyl methacrylate‐grafted polypropylene were selected to study the influence of compatibilizers on the structural and mechanical properties of an LWRT. It was found that the modification effect of PP‐g‐MAH is more significant. Before the mass fraction of PP‐g‐MAH reaches 20%, the tensile and flexural properties of the LWRT increased with the PP‐g‐MAH content. The required content of PP‐g‐MAH in the LWRT is high compared with the voidless composites. Structures with a good matrix distribution and dispersion are anticipated in LWRTs, which are not considered in voidless composites. POLYM. COMPOS., 39:2212–2223, 2018. © 2016 Society of Plastics Engineers
- 9 August 2016
- Published by Wiley in Polymer Composites
- Vol. 39 (7) , 2212-2223
The influence of compatibilizers on the structure and mechanical properties of lightweight reinforced thermoplastics
Lightweight reinforced thermoplastics (LWRT) have a low density and high rigidity. The application of LWRTs to automotive interiors, such as headliners and instrument panels, is very promising. The porous structure of LWRTs is formed in the process of deconsolidation, so pores may appear between the matrix and fibers that interrupt the transfer of stress and deteriorate the mechanical properties. In this article, maleic anhydride‐grafted polypropylene (PP‐g‐MAH) and glycidyl methacrylate‐grafted polypropylene were selected to study the influence of compatibilizers on the structural and mechanical properties of an LWRT. It was found that the modification effect of PP‐g‐MAH is more significant. Before the mass fraction of PP‐g‐MAH reaches 20%, the tensile and flexural properties of the LWRT increased with the PP‐g‐MAH content. The required content of PP‐g‐MAH in the LWRT is high compared with the voidless composites. Structures with a good matrix distribution and dispersion are anticipated in LWRTs, which are not considered in voidless composites. POLYM. COMPOS., 39:2212–2223, 2018. © 2016 Society of Plastics Engineers
- 29 November 2015
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 35 (5) , 408-420
Mechanical properties of unidirectional continuous fiber tapes reinforced long fiber thermoplastics and their manufacturing
In this paper, long fiber thermoplastic was prepared by in-line compounding process and premixed powder impregnation process, respectively, and then comolded with unidirectional continuous fiber tapes. The endless fiber reinforced long fiber thermoplastic was obtained. The effect of the endless fiber fraction on the properties was studied through varying the thickness of the unidirectional composite. It is discovered that the unidirectional continuous fiber can improve toughness dramatically, without sacrificing the strength and stiffness. Fiber length and fiber length distribution may be the significant factors that influence the mechanical properties, especially toughness which can be toughened by fiber bundles as well. The rule of hybrid mixture is suitable to estimate the impact strength.
- 29 November 2015
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 35 (5) , 408-420
Mechanical properties of unidirectional continuous fiber tapes reinforced long fiber thermoplastics and their manufacturing
In this paper, long fiber thermoplastic was prepared by in-line compounding process and premixed powder impregnation process, respectively, and then comolded with unidirectional continuous fiber tapes. The endless fiber reinforced long fiber thermoplastic was obtained. The effect of the endless fiber fraction on the properties was studied through varying the thickness of the unidirectional composite. It is discovered that the unidirectional continuous fiber can improve toughness dramatically, without sacrificing the strength and stiffness. Fiber length and fiber length distribution may be the significant factors that influence the mechanical properties, especially toughness which can be toughened by fiber bundles as well. The rule of hybrid mixture is suitable to estimate the impact strength.