Samuel J. Frank
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Samuel J. Frank has a total of 130 co-authors. Here are the top co-authors by number of shared publications:
- Cary B. Forest
University of Wisconsin-Madison 2 , Madison, Wisconsin 53706
6 shared publications - Douglass Endrizzi
University of Wisconsin–Madison
5 shared publications - Jesse Viola
Realta Fusion, Madison, Wisconsin 53717, USA
5 shared publications - Bodhi Biswas
MIT, Plasma Sci & Fus Ctr, Cambridge, MA 02139 USA
4 shared publications - Craig M. Jacobson
Department of Physics, University of Wisconsin-Madison, 1150 University Avenue, Madison, Wisconsin 53706, USA
3 shared publications - Derek A. Sutherland
CTFusion, Inc. 2 , Seattle, Washington 98121, USA
3 shared publications
Latest Publications
- 1 November 2026
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 97 (11)
Design of a Doppler backscattering diagnostic for WHAM: The Wisconsin HTS Axisymmetric Mirror
The Wisconsin HTS Axisymmetric Mirror (WHAM) is a compact high-field magnetic mirror. In such magnetic mirrors, cross-field transport is dominated by the flute instability [M. Rosenbluth and C. Longmire, Ann. Phys. 1, 120–140 (1957)]. To investigate density fluctuations associated with the flute instability, we designed a Doppler backscattering (DBS) diagnostic for WHAM, to be installed at the midplane port window. The diagnostic uses a two-channel tunable Ka-band (26.5–40 GHz) source and X-mode polarization. The azimuthal launch angle is set mechanically by rotating the external quasi-optical assembly. As such, the system is reconfigurable during dedicated setup periods. Using the Scotty beam-tracing code [V. H. Hall-Chen et al., Plasma Phys. Controlled Fusion 64, 095002 (2022)], we show that the proposed DBS system can measure density fluctuations with perpendicular wavenumbers |k⊥| ≤ 3 cm−1 over radial locations 0.7 ≤ ρ ≤ 0.9, where ρ is the normalized radial coordinate. This is achieved with probe frequencies between 28 and 38.5 GHz, an elevation launch angle of 0°, and azimuthal launch angles in the range of 1°–3°. The selected configurations have low mismatch angles at cutoff, |θm,c| < 1°. The quasi-optical system uses a Ka-band horn and a biconvex ultra-high molecular weight polyethylene lens and satisfies the port-access constraints in WHAM. The planned microwave system has a monostatic, homodyne architecture based on two phase-coupled Ka-band microwave channels. These two channels will be for the transmitted signal and coherent local oscillator for IQ downconversion, respectively. As the two phase-coupled channels can be independently tuned or swept with a controlled frequency offset, the same microwave chain is intended to retain compatibility with future profile-reflectometry operation.
- 1 November 2026
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 97 (11)
Design of a Doppler backscattering diagnostic for WHAM: The Wisconsin HTS Axisymmetric Mirror
The Wisconsin HTS Axisymmetric Mirror (WHAM) is a compact high-field magnetic mirror. In such magnetic mirrors, cross-field transport is dominated by the flute instability [M. Rosenbluth and C. Longmire, Ann. Phys. 1, 120–140 (1957)]. To investigate density fluctuations associated with the flute instability, we designed a Doppler backscattering (DBS) diagnostic for WHAM, to be installed at the midplane port window. The diagnostic uses a two-channel tunable Ka-band (26.5–40 GHz) source and X-mode polarization. The azimuthal launch angle is set mechanically by rotating the external quasi-optical assembly. As such, the system is reconfigurable during dedicated setup periods. Using the Scotty beam-tracing code [V. H. Hall-Chen et al., Plasma Phys. Controlled Fusion 64, 095002 (2022)], we show that the proposed DBS system can measure density fluctuations with perpendicular wavenumbers |k⊥| ≤ 3 cm−1 over radial locations 0.7 ≤ ρ ≤ 0.9, where ρ is the normalized radial coordinate. This is achieved with probe frequencies between 28 and 38.5 GHz, an elevation launch angle of 0°, and azimuthal launch angles in the range of 1°–3°. The selected configurations have low mismatch angles at cutoff, |θm,c| < 1°. The quasi-optical system uses a Ka-band horn and a biconvex ultra-high molecular weight polyethylene lens and satisfies the port-access constraints in WHAM. The planned microwave system has a monostatic, homodyne architecture based on two phase-coupled Ka-band microwave channels. These two channels will be for the transmitted signal and coherent local oscillator for IQ downconversion, respectively. As the two phase-coupled channels can be independently tuned or swept with a controlled frequency offset, the same microwave chain is intended to retain compatibility with future profile-reflectometry operation.
- Open Access
- 10 July 2026
- Published by Cambridge University Press (CUP) in Journal of Plasma Physics
- Vol. 92 (4) , E94
Confinement performance predictions for a high field axisymmetric tandem mirror – CORRIGENDUM
Confinement performance predictions for a high field axisymmetric tandem mirror – CORRIGENDUM - Volume 92 Issue 4
- 10 July 2026
- Published by Cambridge University Press (CUP) in Journal of Plasma Physics
- Vol. 92 (4) , E94
Open AccessConfinement performance predictions for a high field axisymmetric tandem mirror – CORRIGENDUM
Confinement performance predictions for a high field axisymmetric tandem mirror – CORRIGENDUM - Volume 92 Issue 4
- 1 July 2026
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 97 (7)
First implementation of absolute extreme ultraviolet (AXUV) diode-array-based analysis and macro-instability diagnostics on Wisconsin high-temperature superconducting axisymmetric mirror (WHAM).
Absolute extreme ultraviolet (AXUV) diode arrays are widely used in fusion experiments for time-resolved measurements of plasma radiation. We report the first implementation of an AXUV-based analysis framework on the Wisconsin high-temperature superconducting axisymmetric mirror. A single, precisely calibrated 20-channel AXUV assembly measures line-integrated plasma emission with ∼1cm of spatial accuracy across the mid-plane. The data were processed to obtain the plasma's statistical moments, yielding time-resolved measurements of the centroid displacement Φ(t) and effective radius R(t). From the joint covariance of these quantities, we define a macroscopic instability parameter χ(t) that quantifies large-scale plasma evolution directly from AXUV observables. The parameter χ serves as a compact indicator of macroscopic plasma activity, decreasing with increasing end-plate bias and exhibiting strong anti-correlation with diamagnetic flux during confinement transitions. These results demonstrate that a single AXUV array can provide real-time assessment of macroscopic plasma dynamics, constituting the first demonstration of such capability in a magnetic mirror plasma. Future extensions to multiple arrays will further enhance spatial coverage and enable full-mode tracking in axisymmetric mirror configurations and related fusion devices.
- 1 July 2026
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 97 (7)
First implementation of absolute extreme ultraviolet (AXUV) diode-array-based analysis and macro-instability diagnostics on Wisconsin high-temperature superconducting axisymmetric mirror (WHAM).
Absolute extreme ultraviolet (AXUV) diode arrays are widely used in fusion experiments for time-resolved measurements of plasma radiation. We report the first implementation of an AXUV-based analysis framework on the Wisconsin high-temperature superconducting axisymmetric mirror. A single, precisely calibrated 20-channel AXUV assembly measures line-integrated plasma emission with ∼1cm of spatial accuracy across the mid-plane. The data were processed to obtain the plasma's statistical moments, yielding time-resolved measurements of the centroid displacement Φ(t) and effective radius R(t). From the joint covariance of these quantities, we define a macroscopic instability parameter χ(t) that quantifies large-scale plasma evolution directly from AXUV observables. The parameter χ serves as a compact indicator of macroscopic plasma activity, decreasing with increasing end-plate bias and exhibiting strong anti-correlation with diamagnetic flux during confinement transitions. These results demonstrate that a single AXUV array can provide real-time assessment of macroscopic plasma dynamics, constituting the first demonstration of such capability in a magnetic mirror plasma. Future extensions to multiple arrays will further enhance spatial coverage and enable full-mode tracking in axisymmetric mirror configurations and related fusion devices.
- Open Access
- 1 March 2026
- Published by AIP Publishing in Physics of Plasmas
- Vol. 33 (3)
Nonlinear anisotropic equilibrium reconstruction in axisymmetric magnetic mirrors
Magnetic equilibrium reconstruction is a crucial simulation capability for interpreting diagnostic measurements of experimental plasmas. Equilibrium reconstruction has mostly been applied to systems with isotropic pressure and relatively low plasma β=2μ0p/B2. This work extends nonlinear equilibrium reconstruction to high-β plasmas with anisotropic pressure and applies it to the Wisconsin high-temperature superconducting axisymmetric magnetic mirror (WHAM) experiments to infer the presence of sloshing ions. A novel basis set for the plasma profiles and machine-learning algorithm using scalable constrained Bayesian optimization allows accurate nonlinear reconstructions with uncertainty quantification to be made more quickly with fewer experimental diagnostics and improves the robustness of reconstructions at high β. In addition to WHAM and other mirrors, such reconstruction techniques are potentially attractive in high-performance devices with constrained diagnostic capabilities such as fusion power plants.
- 1 March 2026
- Published by AIP Publishing in Physics of Plasmas
- Vol. 33 (3)
Open AccessNonlinear anisotropic equilibrium reconstruction in axisymmetric magnetic mirrors
Magnetic equilibrium reconstruction is a crucial simulation capability for interpreting diagnostic measurements of experimental plasmas. Equilibrium reconstruction has mostly been applied to systems with isotropic pressure and relatively low plasma β=2μ0p/B2. This work extends nonlinear equilibrium reconstruction to high-β plasmas with anisotropic pressure and applies it to the Wisconsin high-temperature superconducting axisymmetric magnetic mirror (WHAM) experiments to infer the presence of sloshing ions. A novel basis set for the plasma profiles and machine-learning algorithm using scalable constrained Bayesian optimization allows accurate nonlinear reconstructions with uncertainty quantification to be made more quickly with fewer experimental diagnostics and improves the robustness of reconstructions at high β. In addition to WHAM and other mirrors, such reconstruction techniques are potentially attractive in high-performance devices with constrained diagnostic capabilities such as fusion power plants.
- Open Access
- 31 July 2025
- Published by Cambridge University Press (CUP) in Journal of Plasma Physics
- Vol. 91 (4) , E110
Confinement performance predictions for a high field axisymmetric tandem mirror
This paper presents a Hammir tandem mirror confinement performance analysis based on Realta Fusion’s first-of-a-kind model for axisymmetric magnetic mirror fusion performance. This model uses an integrated end plug simulation model including, heating, equilibrium and transport combined with a new formulation of the plasma operation contours (POPCONs) technique for the tandem mirror central cell. Using this model in concert with machine learning optimization techniques, it is shown that an end plug utilizing high temperature superconducting magnets and modern neutral beams enables a classical tandem mirror pilot plant producing a fusion gain Q > 5. The approach here represents an important advance in tandem mirror design. The high-fidelity end plug model enables calculations of heating and transport in the highly non-Maxwellian end plug to be made more accurately. The detailed end plug modelling performed in this work has highlighted the importance of classical radial transport and neutral beam absorption efficiency on end plug viability. The central cell POPCON technique allows consideration of a wide range of parameters in the relatively simple near-Maxwellian central cell, facilitating the selection of more optimal central cell plasmas. These advances make it possible to find more conservative classical tandem mirror fusion pilot plant operating points with lower temperatures, neutral beam energies and end plug performance requirements than designs in the literature. Despite being more conservative, it is shown that these operating points have sufficient confinement performance to serve as the basis of a viable fusion pilot plant provided that they can be stabilized against magnetohydrodynamic and trapped particle modes.
- 31 July 2025
- Published by Cambridge University Press (CUP) in Journal of Plasma Physics
- Vol. 91 (4) , E110
Open AccessConfinement performance predictions for a high field axisymmetric tandem mirror
This paper presents a Hammir tandem mirror confinement performance analysis based on Realta Fusion’s first-of-a-kind model for axisymmetric magnetic mirror fusion performance. This model uses an integrated end plug simulation model including, heating, equilibrium and transport combined with a new formulation of the plasma operation contours (POPCONs) technique for the tandem mirror central cell. Using this model in concert with machine learning optimization techniques, it is shown that an end plug utilizing high temperature superconducting magnets and modern neutral beams enables a classical tandem mirror pilot plant producing a fusion gain Q > 5. The approach here represents an important advance in tandem mirror design. The high-fidelity end plug model enables calculations of heating and transport in the highly non-Maxwellian end plug to be made more accurately. The detailed end plug modelling performed in this work has highlighted the importance of classical radial transport and neutral beam absorption efficiency on end plug viability. The central cell POPCON technique allows consideration of a wide range of parameters in the relatively simple near-Maxwellian central cell, facilitating the selection of more optimal central cell plasmas. These advances make it possible to find more conservative classical tandem mirror fusion pilot plant operating points with lower temperatures, neutral beam energies and end plug performance requirements than designs in the literature. Despite being more conservative, it is shown that these operating points have sufficient confinement performance to serve as the basis of a viable fusion pilot plant provided that they can be stabilized against magnetohydrodynamic and trapped particle modes.
- Open Access
- 3 June 2025
- Published by Cambridge University Press (CUP) in Journal of Plasma Physics
- Vol. 91 (3)
Drift-cyclotron loss-cone instability in 3-D simulations of a sloshing-ion simple mirror
The kinetic stability of collisionless, sloshing beam-ion ( $45^\circ$ pitch angle) plasma is studied in a three-dimensional (3-D) simple magnetic mirror, mimicking the Wisconsin high-temperature superconductor axisymmetric mirror experiment. The collisional Fokker–Planck code CQL3D-m provides a slowing-down beam-ion distribution to initialize the kinetic-ion/fluid-electron code Hybrid-VPIC, which then simulates free plasma decay without external heating or fuelling. Over $1$ – $10\;\mathrm{\unicode{x03BC} s}$ , drift-cyclotron loss-cone (DCLC) modes grow and saturate in amplitude. The DCLC scatters ions to a marginally stable distribution with gas-dynamic rather than classical-mirror confinement. Sloshing ions can trap cool (low-energy) ions in an electrostatic potential well to stabilize DCLC, but DCLC itself does not scatter sloshing beam-ions into the said well. Instead, cool ions must come from external sources such as charge-exchange collisions with a low-density neutral population. Manually adding cool $\mathord {\sim } 1\;\mathrm{keV}$ ions improves beam-ion confinement several-fold in Hybrid-VPIC simulations, which qualitatively corroborates prior measurements from real mirror devices with sloshing ions.- 3 June 2025
- Published by Cambridge University Press (CUP) in Journal of Plasma Physics
- Vol. 91 (3)
Open AccessDrift-cyclotron loss-cone instability in 3-D simulations of a sloshing-ion simple mirror
The kinetic stability of collisionless, sloshing beam-ion ( $45^\circ$ pitch angle) plasma is studied in a three-dimensional (3-D) simple magnetic mirror, mimicking the Wisconsin high-temperature superconductor axisymmetric mirror experiment. The collisional Fokker–Planck code CQL3D-m provides a slowing-down beam-ion distribution to initialize the kinetic-ion/fluid-electron code Hybrid-VPIC, which then simulates free plasma decay without external heating or fuelling. Over $1$ – $10\;\mathrm{\unicode{x03BC} s}$ , drift-cyclotron loss-cone (DCLC) modes grow and saturate in amplitude. The DCLC scatters ions to a marginally stable distribution with gas-dynamic rather than classical-mirror confinement. Sloshing ions can trap cool (low-energy) ions in an electrostatic potential well to stabilize DCLC, but DCLC itself does not scatter sloshing beam-ions into the said well. Instead, cool ions must come from external sources such as charge-exchange collisions with a low-density neutral population. Manually adding cool $\mathord {\sim } 1\;\mathrm{keV}$ ions improves beam-ion confinement several-fold in Hybrid-VPIC simulations, which qualitatively corroborates prior measurements from real mirror devices with sloshing ions. - Open Access
- 23 January 2025
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 67 (2) , 029501
Corrigendum: Optimization of the N ∥ upshift in the DIII-D high field side lower hybrid current drive experiment (2024 Plasma Phys. Control. Fusion 66 065024)
- 23 January 2025
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 67 (2) , 029501
Open AccessCorrigendum: Optimization of the N ∥ upshift in the DIII-D high field side lower hybrid current drive experiment (2024 Plasma Phys. Control. Fusion 66 065024)
- Top Cited PapersOpen Access
- 22 August 2024
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 66 (10) , 105006
MANTA: a negative-triangularity NASEM-compliant fusion pilot plant
The MANTA (Modular Adjustable Negative Triangularity ARC-class) design study investigated how negative-triangularity (NT) may be leveraged in a compact, fusion pilot plant (FPP) to take a ‘power-handling first’ approach. The result is a pulsed, radiative, ELM-free tokamak that satisfies and exceeds the FPP requirements described in the 2021 National Academies of Sciences, Engineering, and Medicine (NASEM) report ‘Bringing Fusion to the U.S. Grid’ (2021 Bringing Fusion to the U.S. Grid). A self-consistent integrated modeling workflow predicts a fusion power of 450 MW and a plasma gain of 11.5 with only 23.5 MW of power to the scrape-off layer (SOL). This low P SOL together with impurity seeding and high density at the separatrix results in a peak heat flux of just 2.8 MW m−2. MANTA’s high aspect ratio provides space for a large central solenoid (CS), resulting in ∼15 minute inductive pulses. In spite of the high B fields on the CS and the other REBCO-based magnets, the electromagnetic stresses remain below structural and critical current density limits. Iterative optimization of neutron shielding and tritium breeding blanket yield tritium self-sufficiency with a breeding ratio of 1.15, a blanket power multiplication factor of 1.11, toroidal field coil lifetimes of 3100 ± 400 MW · yr, and poloidal field coil lifetimes of at least 890 ± 40 MW · yr. Following balance of plant modeling, MANTA is projected to generate 90 MW of net electricity at an electricity gain factor of ∼ 2.4 . Systems-level economic analysis estimates an overnight cost of US$3.4 billion, meeting the NASEM FPP requirement that this first-of-a-kind be less than US$5 billion. The toroidal field coil cost and replacement time are the most critical upfront and lifetime cost drivers, respectively.
- 22 August 2024
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 66 (10) , 105006
Top Cited PapersOpen AccessMANTA: a negative-triangularity NASEM-compliant fusion pilot plant
The MANTA (Modular Adjustable Negative Triangularity ARC-class) design study investigated how negative-triangularity (NT) may be leveraged in a compact, fusion pilot plant (FPP) to take a ‘power-handling first’ approach. The result is a pulsed, radiative, ELM-free tokamak that satisfies and exceeds the FPP requirements described in the 2021 National Academies of Sciences, Engineering, and Medicine (NASEM) report ‘Bringing Fusion to the U.S. Grid’ (2021 Bringing Fusion to the U.S. Grid). A self-consistent integrated modeling workflow predicts a fusion power of 450 MW and a plasma gain of 11.5 with only 23.5 MW of power to the scrape-off layer (SOL). This low P SOL together with impurity seeding and high density at the separatrix results in a peak heat flux of just 2.8 MW m−2. MANTA’s high aspect ratio provides space for a large central solenoid (CS), resulting in ∼15 minute inductive pulses. In spite of the high B fields on the CS and the other REBCO-based magnets, the electromagnetic stresses remain below structural and critical current density limits. Iterative optimization of neutron shielding and tritium breeding blanket yield tritium self-sufficiency with a breeding ratio of 1.15, a blanket power multiplication factor of 1.11, toroidal field coil lifetimes of 3100 ± 400 MW · yr, and poloidal field coil lifetimes of at least 890 ± 40 MW · yr. Following balance of plant modeling, MANTA is projected to generate 90 MW of net electricity at an electricity gain factor of ∼ 2.4 . Systems-level economic analysis estimates an overnight cost of US$3.4 billion, meeting the NASEM FPP requirement that this first-of-a-kind be less than US$5 billion. The toroidal field coil cost and replacement time are the most critical upfront and lifetime cost drivers, respectively.
- Open Access
- 1 June 2024
- Published by AIP Publishing in Physics of Plasmas
- Vol. 31 (6)
Simulating energetic ions and enhanced fusion rates from ion-cyclotron resonance heating with a full-wave/Fokker–Planck model
Reproducing fast-ion enhanced fusion rates from ion-cyclotron resonance heating (ICRH) in tokamaks requires the self-consistent coupling of a full-wave solver and a Fokker–Planck solver, which evolves multiple simultaneously resonant ion species. We introduce a new self-consistent model that iterates the TORIC full-wave solver with the CQL3D Fokker–Planck solver using the integrated plasma simulator (IPS). This model evolves the bounce-averaged ion distribution functions in both parallel and perpendicular velocity-space with a quasilinear radio frequency (RF) diffusion operator valid in the ion finite Larmor radius (FLR) limit and the RF electric fields with the resultant non-Maxwellian FLR dielectric tensor. This produces non-Maxwellian ICRH simulations that are fully self-consistent, fast, and interoperable with integrated modeling frameworks, such as TRANSP/GACODE/IPS-FASTRAN. We demonstrate our model's capabilities by validating it against experimental data in Alcator C-Mod. We then perform the first RF heating simulations of SPARC using self-consistent non-Maxwellian ion distributions to investigate the potential to enhance fusion rates using ion cyclotron resonance heating generated fast ions.
- 1 June 2024
- Published by AIP Publishing in Physics of Plasmas
- Vol. 31 (6)
Open AccessSimulating energetic ions and enhanced fusion rates from ion-cyclotron resonance heating with a full-wave/Fokker–Planck model
Reproducing fast-ion enhanced fusion rates from ion-cyclotron resonance heating (ICRH) in tokamaks requires the self-consistent coupling of a full-wave solver and a Fokker–Planck solver, which evolves multiple simultaneously resonant ion species. We introduce a new self-consistent model that iterates the TORIC full-wave solver with the CQL3D Fokker–Planck solver using the integrated plasma simulator (IPS). This model evolves the bounce-averaged ion distribution functions in both parallel and perpendicular velocity-space with a quasilinear radio frequency (RF) diffusion operator valid in the ion finite Larmor radius (FLR) limit and the RF electric fields with the resultant non-Maxwellian FLR dielectric tensor. This produces non-Maxwellian ICRH simulations that are fully self-consistent, fast, and interoperable with integrated modeling frameworks, such as TRANSP/GACODE/IPS-FASTRAN. We demonstrate our model's capabilities by validating it against experimental data in Alcator C-Mod. We then perform the first RF heating simulations of SPARC using self-consistent non-Maxwellian ion distributions to investigate the potential to enhance fusion rates using ion cyclotron resonance heating generated fast ions.
- Open Access
- 9 May 2024
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 66 (6) , 065024
Optimization of the N∥ Upshift in the DIII-D high field side lower hybrid current drive experiment
High field side lower hybrid current drive (LHCD) is one potential candidate for efficient non-inductive current drive in tokamak power plants, and the first test of this technology will occur on the DIII-D tokamak during the 2024 campaign. Previous LFS launch experiments operated in the multi-pass regime and relied on scrape-off layer interactions to close the spectral gap. In the DIII-D experiment, single-pass damping is achievable via an upshift in the parallel refractive index N ∥ caused by mode converting twice (slow → fast → slow). This mode conversion affects the ray trajectories and can lead to enhanced N ∥ upshift depending on where mode conversion occurs. Compared to multi-pass absorption experiments, the optimization of launched N ∥ and plasma parameters can be counter-intuitive: increased density may increase efficiency and smaller N ∥ , launch tend to damp closer to the separatrix. A hard x-ray camera installed to measure the bremsstrahlung (50–250 keV) radiation from LHCD-generated fast electrons is capable of verifying the trends reporting in this paper through comparison to the ray-tracing/Fokker–Planck codes GENRAY/CQL3D.
- 9 May 2024
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 66 (6) , 065024
Open AccessOptimization of the N∥ Upshift in the DIII-D high field side lower hybrid current drive experiment
High field side lower hybrid current drive (LHCD) is one potential candidate for efficient non-inductive current drive in tokamak power plants, and the first test of this technology will occur on the DIII-D tokamak during the 2024 campaign. Previous LFS launch experiments operated in the multi-pass regime and relied on scrape-off layer interactions to close the spectral gap. In the DIII-D experiment, single-pass damping is achievable via an upshift in the parallel refractive index N ∥ caused by mode converting twice (slow → fast → slow). This mode conversion affects the ray trajectories and can lead to enhanced N ∥ upshift depending on where mode conversion occurs. Compared to multi-pass absorption experiments, the optimization of launched N ∥ and plasma parameters can be counter-intuitive: increased density may increase efficiency and smaller N ∥ , launch tend to damp closer to the separatrix. A hard x-ray camera installed to measure the bremsstrahlung (50–250 keV) radiation from LHCD-generated fast electrons is capable of verifying the trends reporting in this paper through comparison to the ray-tracing/Fokker–Planck codes GENRAY/CQL3D.