Dong Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Dong Li has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
Jiong Wang
Nanjing University of Science and Technology
3 shared publications- Fangxu Cai
Nanjing University of Science and Technology
2 shared publications - Huixing Wang
School of Mechanical Engineering, Anhui University of Technology, Maanshan, Anhui, CHINA
2 shared publications - Junyu Chen
Nanjing University of Science and Technology
2 shared publications Fangxu Cai
School of Mechanical Engineering, Nanjing University of Science and Technology, Nanjing, Jiangsu, China
1 shared publication- Fuyun Liu
School of Mechatronic Engineering, Guilin University of Electronic Technology, Guilin 541004, China
1 shared publication
Latest Publications
- 10 September 2026
- Published by SAGE Publications in Journal of Vibration and Control
A novel frequency division control strategy with minimal sensors for commercial vehicle cab suspension using integrated air spring–magnetorheological damper
To address the performance degradation of velocity-dependent semi-active suspension control caused by low-frequency sensor noise and velocity-reconstruction errors, this study develops an integrated magnetorheological damper–air spring (MR–AS) device and a frequency division control (FDC) strategy for commercial vehicle cab suspensions. A three-degree-of-freedom quarter-cab model and a nonlinear MR–AS model incorporating MR hysteresis, air-spring nonlinearity, an auxiliary chamber, and pipeline flow-response dynamics are established. The integrated device is fabricated and experimentally characterized, and its model parameters are identified from harmonic tests. The harmonic balance method is used to interpret the influence of nonlinear air-spring stiffness on the cab frequency response. Guided by the frequency-dependent damping trade-off, FDC determines the damping state from the relative dominance of the low- and high-frequency components of a single measured acceleration signal, thereby avoiding explicit velocity reconstruction. Comparative simulations and real-vehicle road tests demonstrate that FDC suppresses low-frequency resonance while maintaining higher-frequency vibration isolation under practical sensing conditions. Compared with the passive 0 A condition, the FDC reduces the weighted RMS cab accelerations in the x -, y -, and z -directions by 6.9%, 9.9%, and 10.3%, respectively, resulting in an overall vibration reduction of 9.2%. The proposed approach provides a compact and low-complexity solution for semi-active cab-suspension control.
- 10 September 2026
- Published by SAGE Publications in Journal of Vibration and Control
A novel frequency division control strategy with minimal sensors for commercial vehicle cab suspension using integrated air spring–magnetorheological damper
To address the performance degradation of velocity-dependent semi-active suspension control caused by low-frequency sensor noise and velocity-reconstruction errors, this study develops an integrated magnetorheological damper–air spring (MR–AS) device and a frequency division control (FDC) strategy for commercial vehicle cab suspensions. A three-degree-of-freedom quarter-cab model and a nonlinear MR–AS model incorporating MR hysteresis, air-spring nonlinearity, an auxiliary chamber, and pipeline flow-response dynamics are established. The integrated device is fabricated and experimentally characterized, and its model parameters are identified from harmonic tests. The harmonic balance method is used to interpret the influence of nonlinear air-spring stiffness on the cab frequency response. Guided by the frequency-dependent damping trade-off, FDC determines the damping state from the relative dominance of the low- and high-frequency components of a single measured acceleration signal, thereby avoiding explicit velocity reconstruction. Comparative simulations and real-vehicle road tests demonstrate that FDC suppresses low-frequency resonance while maintaining higher-frequency vibration isolation under practical sensing conditions. Compared with the passive 0 A condition, the FDC reduces the weighted RMS cab accelerations in the x -, y -, and z -directions by 6.9%, 9.9%, and 10.3%, respectively, resulting in an overall vibration reduction of 9.2%. The proposed approach provides a compact and low-complexity solution for semi-active cab-suspension control.
- 1 August 2026
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 35 (8) , 085052
Design optimization of a multi-disk shear-type magnetorheological clutch considering nonlinear magnetic and thermal constraints
To address the requirements for miniaturization and high torque density in clutch systems, this study optimizes a multi-plate shear-mode magnetorheological (MR) clutch employing a dry MR powder. First, a nonlinear magnetic circuit model based on the magnetic potential difference theory is established to predict the radial distribution of magnetic flux density. Simultaneously, a thermal resistance network model is employed to determine the maximum allowable excitation current under temperature rise constraints. To ensure the reliability of these theoretical models, finite element analysis is conducted for both the magnetic and thermal circuits, revealing high consistency between the theoretical and simulation results. Subsequently, an optimization design is performed with the objective of maximizing torque density. An integrated optimization framework is constructed by defining the torque equations, establishing constraints—including mechanical structure, magnetic saturation, maximum current, and peak temperature—and identifying the design parameters. Within this framework, Latin hypercube sampling is utilized for spatial exploration, and an orthogonal polynomial surrogate model is selected for response surface fitting based on accuracy evaluation. The optimal solution is then identified using the NLPQLP algorithm. Finally, prototype fabrication and comparative experiments are conducted to verify the effectiveness of the optimized design in enhancing torque density and ensuring thermal stability. The results demonstrate a maximum torque density of 2.19 N.m kg −1 at 2.16 A, representing a 45.4% improvement over the initial design. With high torque density, compact dimensions, millisecond-range response, and experimentally verified thermal reliability, the proposed MR clutch is particularly suitable for high-performance electromechanical systems that demand an optimal combination of space efficiency, fast response, and operational safety. A preliminary integration of the optimized clutch into a robot wrist joint has been successfully demonstrated, highlighting its potential for enhancing compliance and interactive safety in collaborative and service robots.
- 1 August 2026
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 35 (8) , 085052
Design optimization of a multi-disk shear-type magnetorheological clutch considering nonlinear magnetic and thermal constraints
To address the requirements for miniaturization and high torque density in clutch systems, this study optimizes a multi-plate shear-mode magnetorheological (MR) clutch employing a dry MR powder. First, a nonlinear magnetic circuit model based on the magnetic potential difference theory is established to predict the radial distribution of magnetic flux density. Simultaneously, a thermal resistance network model is employed to determine the maximum allowable excitation current under temperature rise constraints. To ensure the reliability of these theoretical models, finite element analysis is conducted for both the magnetic and thermal circuits, revealing high consistency between the theoretical and simulation results. Subsequently, an optimization design is performed with the objective of maximizing torque density. An integrated optimization framework is constructed by defining the torque equations, establishing constraints—including mechanical structure, magnetic saturation, maximum current, and peak temperature—and identifying the design parameters. Within this framework, Latin hypercube sampling is utilized for spatial exploration, and an orthogonal polynomial surrogate model is selected for response surface fitting based on accuracy evaluation. The optimal solution is then identified using the NLPQLP algorithm. Finally, prototype fabrication and comparative experiments are conducted to verify the effectiveness of the optimized design in enhancing torque density and ensuring thermal stability. The results demonstrate a maximum torque density of 2.19 N.m kg −1 at 2.16 A, representing a 45.4% improvement over the initial design. With high torque density, compact dimensions, millisecond-range response, and experimentally verified thermal reliability, the proposed MR clutch is particularly suitable for high-performance electromechanical systems that demand an optimal combination of space efficiency, fast response, and operational safety. A preliminary integration of the optimized clutch into a robot wrist joint has been successfully demonstrated, highlighting its potential for enhancing compliance and interactive safety in collaborative and service robots.
- 30 December 2024
- Published by SAGE Publications in Journal of Intelligent Material Systems and Structures
- Vol. 36 (4) , 242-258
Design and experiment study on a novel magnetorheological impact damper coupled with multiple parallel relief orifices for reducing higher impact peaks
Conventional magnetorheological (MR) dampers exhibit the drawbacks of excessively large and non-adjustable peak force/acceleration during the initial impact in the context of high-impact loads, limiting their applicability in the field of impact resistance. This paper introduces an innovative MR damper (MRD), which, coupled with multiple parallel relief orifices, is capable of effectively mitigating the initial impact peak and enhancing the plateau effect during the mid and late stages of impact. Firstly, the configuration and principle of the novel MRD with multiple orifices (MRDWO) are illustrated and its nonlinear model, based on Bingham-Plastic model and accounting for minor loss, is established. Secondly, the structural design and fabrication of MRDWO were conducted. Simultaneously, for comparative purposes, a traditional MRD with an identical structure to MRDWO, except for the absence of relief orifices, was also fabricated. Then, experimental investigations were conducted separately on MRDWO and MRD without relief orifices (MRDWOO) under various impact velocities and control currents to study their damping forces, accelerations, and displacement responses. Finally, the experimental results of MRDWO were utilized to validate the reliability of the aforementioned nonlinear model. Additionally, a comparative analysis was conducted between MRDWO and MRDWOO under various operating conditions in terms of impact forces, accelerations, and displacements. The results indicate that the novel MRDWO significantly reduces the impact force/acceleration peak during the initial impact and enhances the plateau effect of force/acceleration in mid to later stages, thereby reducing the required displacement for absorbing. This is crucial for mitigating the initial impact damage and improving the damping efficiency of the MR damper.
- 30 December 2024
- Published by SAGE Publications in Journal of Intelligent Material Systems and Structures
- Vol. 36 (4) , 242-258
Design and experiment study on a novel magnetorheological impact damper coupled with multiple parallel relief orifices for reducing higher impact peaks
Conventional magnetorheological (MR) dampers exhibit the drawbacks of excessively large and non-adjustable peak force/acceleration during the initial impact in the context of high-impact loads, limiting their applicability in the field of impact resistance. This paper introduces an innovative MR damper (MRD), which, coupled with multiple parallel relief orifices, is capable of effectively mitigating the initial impact peak and enhancing the plateau effect during the mid and late stages of impact. Firstly, the configuration and principle of the novel MRD with multiple orifices (MRDWO) are illustrated and its nonlinear model, based on Bingham-Plastic model and accounting for minor loss, is established. Secondly, the structural design and fabrication of MRDWO were conducted. Simultaneously, for comparative purposes, a traditional MRD with an identical structure to MRDWO, except for the absence of relief orifices, was also fabricated. Then, experimental investigations were conducted separately on MRDWO and MRD without relief orifices (MRDWOO) under various impact velocities and control currents to study their damping forces, accelerations, and displacement responses. Finally, the experimental results of MRDWO were utilized to validate the reliability of the aforementioned nonlinear model. Additionally, a comparative analysis was conducted between MRDWO and MRDWOO under various operating conditions in terms of impact forces, accelerations, and displacements. The results indicate that the novel MRDWO significantly reduces the impact force/acceleration peak during the initial impact and enhances the plateau effect of force/acceleration in mid to later stages, thereby reducing the required displacement for absorbing. This is crucial for mitigating the initial impact damage and improving the damping efficiency of the MR damper.
- 22 February 2024
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 33 (3) , 035035
Design and experiment study of a novel dual-channel independent-coil magnetorheological grease damper
In order to address the issue of reduced damping force dynamic range in magnetorheological (MR) damper caused by the high zero-field viscosity of MR grease, known for its sedimentation stability, this paper introduces a novel dual-channel independent-coil MR damper (DCICMRD). Firstly, the dual-channel configuration and the magnetic circuit structure of independent coils were meticulously designed, and a genetic algorithm was employed to conduct multi-objective optimization of the structural parameters for DCICMRD. The optimization results indicate that all performance metrics of the damper post-optimization exhibit improvements exceeding 15%. Then, the theocratical model of the damping force for DCICMRD under three operational modes are established, and the output damping force of various input currents for different operating mode is obtained. Finally, the DCICMRD was manufactured and subjected to dynamic performance testing. The results revealed that the damping force dynamic range in Mode III, i.e. dual-channel structure, can achieve approximately 15 times, whereas Mode I, i.e. traditional single-channel structure, only attains approximately 9 times. The aforementioned research holds significant implications for expanding the further engineering applications of MR dampers.
- 22 February 2024
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 33 (3) , 035035
Design and experiment study of a novel dual-channel independent-coil magnetorheological grease damper
In order to address the issue of reduced damping force dynamic range in magnetorheological (MR) damper caused by the high zero-field viscosity of MR grease, known for its sedimentation stability, this paper introduces a novel dual-channel independent-coil MR damper (DCICMRD). Firstly, the dual-channel configuration and the magnetic circuit structure of independent coils were meticulously designed, and a genetic algorithm was employed to conduct multi-objective optimization of the structural parameters for DCICMRD. The optimization results indicate that all performance metrics of the damper post-optimization exhibit improvements exceeding 15%. Then, the theocratical model of the damping force for DCICMRD under three operational modes are established, and the output damping force of various input currents for different operating mode is obtained. Finally, the DCICMRD was manufactured and subjected to dynamic performance testing. The results revealed that the damping force dynamic range in Mode III, i.e. dual-channel structure, can achieve approximately 15 times, whereas Mode I, i.e. traditional single-channel structure, only attains approximately 9 times. The aforementioned research holds significant implications for expanding the further engineering applications of MR dampers.
- Open Access
- 26 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 90958-90970
Nonlinear Damping Curve Control of Semi-Active Suspension Based on Improved Particle Swarm Optimization
This paper studies the semi-active suspension damping control algorithm. The shortcomings of traditional damping control algorithms such as the sky-hook algorithm and the acceleration-driven damper algorithms are analyzed in this article. For the shortcomings of the traditional damping control algorithm, a semi-active suspension damping control strategy based on improved particle swarm optimization is proposed. The proposed algorithm uses the dynamic nonlinear inertia coefficient instead of the fixed inertia coefficient of the traditional particle swarm algorithm, which improves solution efficiency and accuracy. Nonlinear damping curves for different forms of expression are optimized using the algorithm, and the optimal nonlinear damping curve for the white noise pavement is obtained. A simulation model is established to verify the effect of the proposed algorithm. The simulation results show that the nonlinear semi-active control strategy can achieve the target of high vibration isolation coefficient at high frequency and strong inhibitory resonance ability at low frequency. Moreover, the jerk of the spring mass does not deteriorate by a large margin. The results show that the nonlinear semi-active control strategy improves the driving comfort of the vehicle.
- 26 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 90958-90970
Open AccessNonlinear Damping Curve Control of Semi-Active Suspension Based on Improved Particle Swarm Optimization
This paper studies the semi-active suspension damping control algorithm. The shortcomings of traditional damping control algorithms such as the sky-hook algorithm and the acceleration-driven damper algorithms are analyzed in this article. For the shortcomings of the traditional damping control algorithm, a semi-active suspension damping control strategy based on improved particle swarm optimization is proposed. The proposed algorithm uses the dynamic nonlinear inertia coefficient instead of the fixed inertia coefficient of the traditional particle swarm algorithm, which improves solution efficiency and accuracy. Nonlinear damping curves for different forms of expression are optimized using the algorithm, and the optimal nonlinear damping curve for the white noise pavement is obtained. A simulation model is established to verify the effect of the proposed algorithm. The simulation results show that the nonlinear semi-active control strategy can achieve the target of high vibration isolation coefficient at high frequency and strong inhibitory resonance ability at low frequency. Moreover, the jerk of the spring mass does not deteriorate by a large margin. The results show that the nonlinear semi-active control strategy improves the driving comfort of the vehicle.