RBR. V. Belyanin

R. V. Belyanin

*This is an algorithmically generated author record based on publicly available information.

R. V. Belyanin has a total of 19 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Influence of non-sinusoidal voltages on electromechanical stresses in cross-linked polyethylene insulation with micro-defects of power electrical cables

    by A. A. Shcherba, O. D. Podoltsev, M. A. Shcherba, T. Yu. Antonets, R. V. Belyanin

    Introduction. Power cables with cross-linked polyethylene (XLPE) insulation have significant advantages over traditional oil-filled ones, which have led to their widespread use in high-power electrical networks of all developed countries. However, such cables are increasingly forced to operate under conditions of non-sinusoidal voltages caused by the use of non-linear loads and powerful high-frequency converters of electricity parameters. Problem. Non-sinusoidal voltages and currents in power networks increase nonlinear dielectric losses in XLPE cable insulation, and also intensify the processes of accumulation of space charges (SCs) in the insulation and electromechanical loads near its micro-defects (in particular, water micro-trees) and the occurrence of destructive partial discharges (PDs), which can accelerate the degradation processes of XLPE insulation. All these processes require attention during testing and operation of cables. Goal. To clarify the influence of higher harmonic voltage components on local electric field amplification and Maxwell electromechanical pressures near water micro-inclusions and trees in high-voltage cross-linked polyethylene insulation of power cables. Methodology. The use of the finite element method to determine the dependences of the EF strength distribution, stressed volume, and Maxwell pressure on the geometric characteristics of micro-defects and their location, which affect the EF amplification in XLPE cable insulation under the action of non-sinusoidal power supply voltages. Results. The analysis of the main mechanisms and factors that accelerate the degradation of XLPE cable insulation under the influence of non-sinusoidal voltages has been carried out: an increase in dielectric losses, PDs intensity, distortion of accumulated SCs, acceleration of the development of water trees, the occurrence of higher harmonics and resonant overvoltage. The dependence of the maximum EF strengths and force effects in XLPE cable insulation on the configuration, mutual arrangement and orientation of micro-inclusions relative to the EF was determined. Scientific novelty. The development of the theory of the force influence of non-sinusoidal EF on the electromechanical degradation of the cross-linked polyethylene insulation of power cables based on the establishment of relationships between the configuration features and mutual arrangement of micro-defects and local field amplifications, which leads to an increase in local stressed volumes and Maxwell pressures in the cross-linked polyethylene insulation. Practical value. The obtained results are useful for estimating the stressed volume and Maxwell pressures in the XLPE insulation caused by more complex configurations and mutual arrangement of micro-defects in the insulation of power cables under the influence of non-sinusoidal voltage. References 31, figures 6.

  • Open Access

    Principles of building powerful microgrids for uninterrupted power supply of industrial enterprises

    by A. A. Shcherba, O. D. Podoltsev, N. I. Suprunovska, R. V. Belyanin

    Introduction. In conditions of unstable external power supply, industrial enterprises with critical electrical technological processes require reliable backup power supply. Traditional approaches to power supply backup, based on separate diesel generators or uninterruptible power supply systems, do not provide the required quality and continuity of power supply during long-term emergency outages from the national power grid. Problem. Existing theoretical principles for building microgrids are focused mainly on single-phase distribution networks of low power and do not take into account the features of powerful three-phase industrial microgrids. In particular, the problems of ensuring system stability under conditions of low inertia (absence of rotating masses of generators) and implementing «seamless» transitions between the parallel operation mode with the external grid and the autonomous («island») mode, as well as effective local power balancing taking into account the priority of consumers, remain unresolved. Goal. Development of the principles for building powerful three-phase microgrids capable of providing uninterrupted and high-quality power supply to industrial enterprises with critical energy consumers in conditions of unstable general power supply. Methodology. The study is based on a systematic analysis of international standards and modern publications in the field of microgrids, hierarchical control theory, methods of computer modeling of microgrid modes, as well as on the generalization of experience in designing, installing and long-term (more than one year) experimental and industrial operation of a microgrid with a capacity of more than 1.5 MVA at a real industrial enterprise in Ukraine. Results. Six basic principles for building powerful industrial microgrids have been developed and systematized. The effectiveness of these principles is confirmed by the successful operation of the designed microgrid, which includes a cogeneration unit (up to 1.5 MW), a diesel generator (up to 825 kW), a solar station (72.5 kW), four specialized uninterruptible power supplies with a total capacity of up to 1.95 MW, and an electricity storage unit with a capacity of up to 10 MWh. Scientific novelty. For the first time, the principles for building powerful three-phase industrial microgrids has been developed as a system of six interconnected principles, which, unlike existing approaches, cover the physical aspects of stabilization, system aspects of control and quality aspects of electricity (reactive power compensation, load balancing). The proposed principles are intended for microgrids with a capacity of more than 1 MVA and take into account the specifics of industrial enterprises. Practical value. The proposed principles provide a methodological basis for the design and modernization of powerful industrial microgrids in Ukraine and other countries with unstable power supply. References 36, figures 3.

  • Open Access

    DIRECTIONS FOR DEVELOPMENT OF HIGH-POWER MICROGRIDS FOR INDUSTRIAL ENTERPRISES OF UKRAINE

    by A.A. Shcherba, O.D. Podoltsev, N.I. Suprunovska, R.V. Belyanin, T.YU. Antonets

    Research has been conducted into the directions of development of high-power microgrids capable of ensuring the uninterrupted operation of critical electrotechnological equipment at industrial enterprises of Ukraine under unstable external power supply conditions. Improvements to such microgrids are substantiated based on the use of autonomous distributed energy sources and modern technologies for accumulation, storage and conversion of electrical energy parameters, and on the integration of artificial intelligence and energy management methods. The key role of high-power microgrids in ensuring guaranteed power supply to critical energy consumers of industrial enterprises during prolonged outages and unstable external supply conditions has been identified. It is substantiated that the integration of high-power microgrids, modern "smart" mechanism technologies and hybrid energy systems at industrial enterprises increase the energy efficiency of all electrical, technological and organizational processes and their resilience to prolonged outages and external power supply instabilities. The introduction of high-power microgrids at industrial enterprises in Ukraine increases the energy efficiency of all electrotechnologies for the production of critically important products and facilitates the achievement of sustainable development goals. References 19, figure 1.

  • Open Access

    MODELING AND ANALYSIS OF LONG-TERM 24-HOUR PROCESSES OF CHANGES IN ELECTRICAL ENERGY FLOWS IN THE MICROGRID OF AN INDUSTRIAL ENTERPRISE

    by A.A. Shcherba, O.D. Podoltsev, R.V. Belyanin, Pjsc Yuzhcable Works, T.YU. Antonets, Yu.V. Dadazhanov, Т.ю. Антонець

    The paper considers the energy strategy for implementing reliable uninterrupted power supply of critically important technological equipment of an industrial enterprise of Ukraine in modern military conditions by creating its industrial microgrid and solving scientific and technical problems regarding the optimal use of its elements and reducing overall costs, which take into account the cost of electricity received from each source of the microgrid. To solve this problem, a computer modeling method was used. It is shown that for modeling long-term (24-hour) electromagnetic processes in a microgrid, it is advisable to use a generalized method for calculating complex currents, which is usually used to calculate sinusoidal current electrical circuits. However, in this task, it is also necessary to take into account that in a microgrid, not only the amplitudes of currents change slowly over time, but also their phases, so it is advisable to use the dynamic phasor method, according to which the calculation is performed simultaneously in the complex and time planes. To implement this method in the Matlab/Simulink package, it is necessary to develop appropriate system models for all power sources and time-varying loads. The paper presents the results of calculating long-term (over a day) active and reactive power flows in the microgrid of a typical industrial enterprise, which contains such power sources as a solar power plant and a cogeneration unit, which can operate both in parallel with the external power grid and without it. The daily costs of electricity obtained from each power source are determined. In order to identify ways to reduce the total cost of electricity, the paper considers various scenarios for connecting power sources and determines their impact on the total daily costs of the enterprise. References 32, figures 8, table 1.


  • Open Access

    STABILITY OF POWER CABLES UNDER FIRE CONDITIONS. COMPUTER AND EXPERIMENTAL STUDY

    by A.A. Shcherba, O.D. Podoltsev, I.M. Kucheriava, S.S. Roziskulov, R.V. Belyanin, Pjsc Yuzhcable Works, T.YU. Antonets, І.м. Кучерява, Т.ю. Антонець

    The work is dedicated to the experimental and numerical study of ways to increase the resource and reliability of power cables under fire emergency conditions. Firstly the computer model is developed and the temperature field in XLPE-insulated power cable operating at fire emergency is studied. The thermal processes in the case of the fireproof coating with different thickness located on the central section of the cable around it are analyzed. Two main factors of the additional coating are revealed: 1) the time of stable reliable operation of the cable at fire gradually increases with an increase in the thickness of the coating (a positive factor); 2) under normal operating conditions, due to cooling deterioration, the temperature of the insulation on the section of the cable, corresponding to the coating, increases with an increase in the thickness of the coating (a negative factor). Such factors should be taken into account when applying and choosing the dimensions of the coating. At the second stage of the work, the experimental study of power cable destruction under conditions close to a fire, i.e. under the direct influence of open flame, is carried out. The time from the beginning of the fire, during which the cable under the influence of the flame allows powering the load, is determined. References 17, figures 10.

  • RESEARCH OF ACTIVE POWER TRANSFER IN AN INSTALLATION FOR INDUCTION HEAT TREATMENT OF CYLINDRICAL ALUMINUM BILLETS WITH A THREE-PHASE INDUCTOR

    by A.F. Zharkin, Yu.M. Goryslavets, O.I. Gluhenky, R.V. Belyanin, Pjsc Yuzhcable Works

    For the proposed design variant of a three-phase inductor of a device for induction heat treatment of cylindrical aluminum billets, which is used in the technology of production of conductive cores of power cables before pressing of wire rod, using the developed mathematical model of electrothermal processes, the process of active power transfer between phase sections and along the length of the billets, which occurs in the inductor due to inductive coupling between phase windings, has been investigated. It was established that the side phase sections of the inductor are characterized by the lack of balance between the active power consumed from the power supply network and the total heat dissipation in the phase section and the corresponding part of the aluminum billet, while this balance is fulfilled for the central phase section and the inductor as a whole. The distribution along the length and radius of the induction installation of the axial component of the electromagnetic field energy flux density vector was obtained, which confirms the presence of active power transfer between adjacent phase sections of the three-phase inductor and indicates its absence along the aluminum billets (on the secondary side of the system). It was established that the transfer of active power between the phase sections of the inductor has practically no effect on the heating of the aluminum billets. It was determined that the negative consequence of the transfer of active power between the phase sections of the three-phase inductor is the uneven load of the phases of the electrical network. A rational power supply scheme for a three-phase three-layer inductor from a three-phase industrial electrical network is proposed, which provides the maximum possible energy efficiency of the induction installation with minimal unevenness of the phases load of the electrical network. Ref. 9, fig. 6, table.

  • Open Access

    MULTILAYER INDUCTORS FOR INDUCTION HEAT TREATMENT INSTALLATION OF ALUMINUM CASTINGS WHEN PRESSING RODS FOR POWER CABLES

    by A.F. Zharkin, Yu.M. Goryslavets, O.I. Gluhenky, R.V. Belyanin, Pjsc Yuzhcable Works

    On the basis of the developed mathematical model, computer (numerical) modeling of electrothermal processes in a multi-layer inductor installation, which is used for heating cylindrical aluminum ingots (blanks) before pressing the wire rod, as a basis for obtaining current-conducting cores of power cables from it, was carried out. Single-phase and three-phase multilayer inductors of the galette type were studied, as a result of which it was shown that the maximum value of the electrical efficiency of such an installation for both inductors is provided by their three-layer winding with a water-cooled copper tube of rectangular section. For both inductors, distributions along the radius and length of the aluminum blanks of the volumetric specific power and the specific linear power of heat release from the eddy currents induced in the blanks were obtained. For a three-phase inductor, such distributions were obtained when feeding it with voltages with phase shift angles of 120 and 60 degrees. The losses in the turns of the inductors and their distribution along the length and layers of both inductors were also studied. Ref. 8, fig. 7, tables 2.


  • Open Access

    Modeling and analysis of electro-thermal processes in installations for induction heat treatment of aluminum cores of power cables

    by A. A. Shcherba, O. D. Podoltsev, N. I. Suprunovska, R. V. Bilianin, T. Yu. Antonets, I. M. Masluchenko

    Introduction. The development of the electric power industry is directly related to the improvement of cable lines. Cable lines meet modern requirements for reliability, they are increasingly used. Problem. Currently, power cables with an aluminum multi-conductor core, which requires heat treatment - an annealing process at the stage of the technological manufacturing process, are widespread. This process makes it possible to desirably reduce the electrical resistance of the wire and increase its flexibility. For effective use of induction heating during annealing of an aluminum core, it is necessary to determine the optimal frequency of the power source of the inductor. Considering the long length of the inductor and the large number of its turns, the numerical calculation of the electromagnetic field, which is necessary for calculating the equivalent electrical parameters of the turns of the inductor and its efficiency, requires significant computer resources. The goal is to develop a computer model for calculating electro-thermal processes in an induction plant for heating (up to the annealing temperature) an aluminum core of a power cable moving in the magnetic field of a long multi-turn inductor, as well as obtaining frequency dependences of the equivalent R, L parameters of such an inductor and determining the optimal the value of the frequency of the power source, which corresponds to the maximum value of the electrical efficiency of the inductor. Methodology. The mathematical model was developed to analyze the coupled electromagnetic and thermal processes occurring in a core moving in a time-harmonic magnetic field of an inductor at a constant speed. The differential equations for the electromagnetic and temperature fields, taking into account the boundary conditions, represent a coupled electro-thermal problem that was solved numerically by the finite element method using the Comsol software package. For a detailed analysis of the electromagnetic processes in the inductor, an additional problem was considered at the level of the elementary cell, which includes one turn of the inductor and a fragment of the core located near this turn. Results. According to the results of the calculation of the electromagnetic field in the area of the elementary cell, the equivalent electrical parameters of one turn of the inductor and the entire multi-turn inductor were calculated depending on the frequency of the electric current. The frequency dependences of the electrical efficiency of the inductor were calculated. Originality. Taking into account the design features of the inductor (its long length and large number of turns), the method of multiscale modeling was used. Electro-thermal processes in the core were studied at the macro level, and the distribution of the electromagnetic field and electric current density in the cross-section of the massive copper turn of the inductor was calculated at the micro level – at the level of an elementary cell containing only one turn of the inductor. The frequency dependences of the equivalent R, L parameters of the inductor, taking into account the skin effect, the proximity effect, and the geometric effect, were obtained, and the quantitative influence of the electric current frequency on these effects was studied. Practical value. The dependence of the electrical efficiency of the inductor on the frequency of the power source was obtained and it was shown that for effective heating of an aluminum core with a diameter of 28 mm, the optimal value of the frequency is in the range of 1–2 kHz, and at the same time the electrical efficiency reaches values of ηind = 0.3–0.33, respectively.


  • Open Access

    SIMULATION OF ELECTRO-THERMAL PROCESSES IN THE INSTALLATION OF INDUCTION HEAT TREATMENT OF ALUMINUM CASTINGS AND DETERMINATION OF WAYS TO INCREASE ITS EFFICIENCY WHEN PRESSING WIRE ROD FOR POWER CABLES

    by A.F. Zharkin, Yu.M. Goryslavets, O.I. Glukhenky, V.V. Zolotaryov, Pjsc Yuzhcable Works, R.V. Belyanin, Ю.м. Гориславець, О.і. Глухенький

    A computer mathematical model is presented for the study of electrothermal processes in the installation of induction heat treatment of cylindrical aluminum ingots during pressing of wire rod for the manufacture of aluminum wire for power cables. The model makes it possible to determine energetically and technologically appropriate electromagnetic and thermal modes of induction heat treatment of ingots at a given voltage on the inductor. The results of the study of a typical installation for heating aluminum blanks for the purpose of their subsequent gradient pressing using a single-phase single-layer cylindrical inductor made of a rectangular copper tube are presented. Temperature distributions along the length of the aluminum blanks, as well as in the cross-sections of the billets at the output of the inductor, were obtained. A slight difference in the calculated electromagnetic and thermal parameters from the similar parameters of the operating installation confirmed the adequacy of the developed model. Ways to increase the efficiency of the induction heating installation by optimizing the profile of the inductor turns are considered. The influence of the thickness of the wall of the copper tube of the inductor close to the workpiece on the efficiency of the installation was determined and it was shown that its optimal thickness is at the level of the depth of penetration of the electromagnetic field into the metal. The possibility of using a three-phase power supply of the inductor was also investigated and it was shown that in this case it is most appropriate to use a phase angle shift between voltages of 60 el. degree. References 10, tables 2, figures 7.


  • Open Access

    MATHEMATICAL MODELING AND REGULATION OF PROCESSES OF COMPLEX ELECTRO-HEAT TREATMENT OF ALUMINUM CORE OF POWER CABLE

    by A.A. Shcherba, O.D. Podoltsev, V.V. Zolotaryov, R.V. Belyanin, M.A. Kulyk, Pjsc Yuzhcable Works

    In the work using the finite element method, a three-dimensional computer model of the processes of electrothermal treatment of an aluminum core of a power cable in an electric furnace and a thermostat was developed, and the pat-terns of changes in the temperature field in such a core were determined under different modes of implementation of the so-called "annealing" processes, that is, the restoration of the necessary electrical properties in it , in particular, an increase in specific electrical conductivity and plasticity. Calculations based on the developed mathematical model and the obtained regularities are consistent with the results of practical measurements of electrical conductivity and plastic-ity of experimental samples of aluminum cores of cables manufactured by YUZHCABLE WORKS, PJSC, Kharkiv. However, the analysis of the patterns of changes in the temperature field in the volume of aluminum cores of cables during their continuous electric heating to the required temperatures of both the outer and inner layers of the core wound on a spool showed that the difference in their temperatures can exceed 500 С. Such nonuniformity of the tem-perature field of the core and long-term overheating of its outer layers leads to unacceptable losses of electricity and reduces the positive result of the processes of such heat treatment of the core, in particular, regarding the increase of its electrical conductivity. It is substantiated that in order to reduce the loss of electricity and the nonuniformity of the temperature field in the aluminum core, it is necessary to reduce the duration of electric heating of the aluminum core to the temperature of its upper layers, necessary for annealing, and then move the drum with such a core to a thermo-stat without electronic heating elements. In such a thermostat, the temperature of the outer layers will decrease, and the temperature of the inner layers will continue to increase. The work shows that after some time (≈ 60 min), the tempera-ture distribution in the core will become almost uniform, and the total losses of electricity and the nonuniformity of the temperature field in the volume of the core will become smaller. Based on the results of the calculations, recommenda-tions were developed for the selection of appropriate modes of heat treatment of aluminum cores wound on a spool, with acceptable energy consumption and overheating of the upper layers of the core. Ref. 8, fig. 4.