Aleksandr Dmitrievich Podoltsev
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Aleksandr Dmitrievich Podoltsev has a total of 81 co-authors. Here are the top co-authors by number of shared publications:
- Anatolii A. Shcherba
Institute of Electrodynamics of the National Academy of Sciences of Ukraine, Ukraine
16 shared publications I.M. Kucheriava
Institute of Electrodynamics National Academy of Sciences of Ukraine, 56, Beresteiskyi, Kyiv, 03057, Ukraine
10 shared publications- R. V. Belyanin
YUZHCABLE WORKS, PJSC, Ukraine
7 shared publications - Yuriy V. Serdyuk
Chalmers University of Technology, Gothenburg, Sweden
7 shared publications Stanislaw M. Gubanski
5 shared publications- T. Yu. Antonets
YUZHCABLE WORKS, PJSC, Ukraine
5 shared publications
Latest Publications
- Open Access
- 2 September 2026
- Published by National Technical University Kharkiv Polytechnic Institute in Electrical Engineering & Electromechanics
- No. 5,p. 66-75
Influence of non-sinusoidal voltages on electromechanical stresses in cross-linked polyethylene insulation with micro-defects of power electrical cables
Introduction. Power cables with cross-linked polyethylene (XLPE) insulation have significant advantages over traditional oil-filled ones, which have led to their widespread use in high-power electrical networks of all developed countries. However, such cables are increasingly forced to operate under conditions of non-sinusoidal voltages caused by the use of non-linear loads and powerful high-frequency converters of electricity parameters. Problem. Non-sinusoidal voltages and currents in power networks increase nonlinear dielectric losses in XLPE cable insulation, and also intensify the processes of accumulation of space charges (SCs) in the insulation and electromechanical loads near its micro-defects (in particular, water micro-trees) and the occurrence of destructive partial discharges (PDs), which can accelerate the degradation processes of XLPE insulation. All these processes require attention during testing and operation of cables. Goal. To clarify the influence of higher harmonic voltage components on local electric field amplification and Maxwell electromechanical pressures near water micro-inclusions and trees in high-voltage cross-linked polyethylene insulation of power cables. Methodology. The use of the finite element method to determine the dependences of the EF strength distribution, stressed volume, and Maxwell pressure on the geometric characteristics of micro-defects and their location, which affect the EF amplification in XLPE cable insulation under the action of non-sinusoidal power supply voltages. Results. The analysis of the main mechanisms and factors that accelerate the degradation of XLPE cable insulation under the influence of non-sinusoidal voltages has been carried out: an increase in dielectric losses, PDs intensity, distortion of accumulated SCs, acceleration of the development of water trees, the occurrence of higher harmonics and resonant overvoltage. The dependence of the maximum EF strengths and force effects in XLPE cable insulation on the configuration, mutual arrangement and orientation of micro-inclusions relative to the EF was determined. Scientific novelty. The development of the theory of the force influence of non-sinusoidal EF on the electromechanical degradation of the cross-linked polyethylene insulation of power cables based on the establishment of relationships between the configuration features and mutual arrangement of micro-defects and local field amplifications, which leads to an increase in local stressed volumes and Maxwell pressures in the cross-linked polyethylene insulation. Practical value. The obtained results are useful for estimating the stressed volume and Maxwell pressures in the XLPE insulation caused by more complex configurations and mutual arrangement of micro-defects in the insulation of power cables under the influence of non-sinusoidal voltage. References 31, figures 6.
- 2 September 2026
- Published by National Technical University Kharkiv Polytechnic Institute in Electrical Engineering & Electromechanics
- No. 5,p. 66-75
Open AccessInfluence of non-sinusoidal voltages on electromechanical stresses in cross-linked polyethylene insulation with micro-defects of power electrical cables
Introduction. Power cables with cross-linked polyethylene (XLPE) insulation have significant advantages over traditional oil-filled ones, which have led to their widespread use in high-power electrical networks of all developed countries. However, such cables are increasingly forced to operate under conditions of non-sinusoidal voltages caused by the use of non-linear loads and powerful high-frequency converters of electricity parameters. Problem. Non-sinusoidal voltages and currents in power networks increase nonlinear dielectric losses in XLPE cable insulation, and also intensify the processes of accumulation of space charges (SCs) in the insulation and electromechanical loads near its micro-defects (in particular, water micro-trees) and the occurrence of destructive partial discharges (PDs), which can accelerate the degradation processes of XLPE insulation. All these processes require attention during testing and operation of cables. Goal. To clarify the influence of higher harmonic voltage components on local electric field amplification and Maxwell electromechanical pressures near water micro-inclusions and trees in high-voltage cross-linked polyethylene insulation of power cables. Methodology. The use of the finite element method to determine the dependences of the EF strength distribution, stressed volume, and Maxwell pressure on the geometric characteristics of micro-defects and their location, which affect the EF amplification in XLPE cable insulation under the action of non-sinusoidal power supply voltages. Results. The analysis of the main mechanisms and factors that accelerate the degradation of XLPE cable insulation under the influence of non-sinusoidal voltages has been carried out: an increase in dielectric losses, PDs intensity, distortion of accumulated SCs, acceleration of the development of water trees, the occurrence of higher harmonics and resonant overvoltage. The dependence of the maximum EF strengths and force effects in XLPE cable insulation on the configuration, mutual arrangement and orientation of micro-inclusions relative to the EF was determined. Scientific novelty. The development of the theory of the force influence of non-sinusoidal EF on the electromechanical degradation of the cross-linked polyethylene insulation of power cables based on the establishment of relationships between the configuration features and mutual arrangement of micro-defects and local field amplifications, which leads to an increase in local stressed volumes and Maxwell pressures in the cross-linked polyethylene insulation. Practical value. The obtained results are useful for estimating the stressed volume and Maxwell pressures in the XLPE insulation caused by more complex configurations and mutual arrangement of micro-defects in the insulation of power cables under the influence of non-sinusoidal voltage. References 31, figures 6.
- Open Access
- 2 July 2026
- Published by National Technical University Kharkiv Polytechnic Institute in Electrical Engineering & Electromechanics
- No. 4,p. 74-83
Principles of building powerful microgrids for uninterrupted power supply of industrial enterprises
Introduction. In conditions of unstable external power supply, industrial enterprises with critical electrical technological processes require reliable backup power supply. Traditional approaches to power supply backup, based on separate diesel generators or uninterruptible power supply systems, do not provide the required quality and continuity of power supply during long-term emergency outages from the national power grid. Problem. Existing theoretical principles for building microgrids are focused mainly on single-phase distribution networks of low power and do not take into account the features of powerful three-phase industrial microgrids. In particular, the problems of ensuring system stability under conditions of low inertia (absence of rotating masses of generators) and implementing «seamless» transitions between the parallel operation mode with the external grid and the autonomous («island») mode, as well as effective local power balancing taking into account the priority of consumers, remain unresolved. Goal. Development of the principles for building powerful three-phase microgrids capable of providing uninterrupted and high-quality power supply to industrial enterprises with critical energy consumers in conditions of unstable general power supply. Methodology. The study is based on a systematic analysis of international standards and modern publications in the field of microgrids, hierarchical control theory, methods of computer modeling of microgrid modes, as well as on the generalization of experience in designing, installing and long-term (more than one year) experimental and industrial operation of a microgrid with a capacity of more than 1.5 MVA at a real industrial enterprise in Ukraine. Results. Six basic principles for building powerful industrial microgrids have been developed and systematized. The effectiveness of these principles is confirmed by the successful operation of the designed microgrid, which includes a cogeneration unit (up to 1.5 MW), a diesel generator (up to 825 kW), a solar station (72.5 kW), four specialized uninterruptible power supplies with a total capacity of up to 1.95 MW, and an electricity storage unit with a capacity of up to 10 MWh. Scientific novelty. For the first time, the principles for building powerful three-phase industrial microgrids has been developed as a system of six interconnected principles, which, unlike existing approaches, cover the physical aspects of stabilization, system aspects of control and quality aspects of electricity (reactive power compensation, load balancing). The proposed principles are intended for microgrids with a capacity of more than 1 MVA and take into account the specifics of industrial enterprises. Practical value. The proposed principles provide a methodological basis for the design and modernization of powerful industrial microgrids in Ukraine and other countries with unstable power supply. References 36, figures 3.
- 2 July 2026
- Published by National Technical University Kharkiv Polytechnic Institute in Electrical Engineering & Electromechanics
- No. 4,p. 74-83
Open AccessPrinciples of building powerful microgrids for uninterrupted power supply of industrial enterprises
Introduction. In conditions of unstable external power supply, industrial enterprises with critical electrical technological processes require reliable backup power supply. Traditional approaches to power supply backup, based on separate diesel generators or uninterruptible power supply systems, do not provide the required quality and continuity of power supply during long-term emergency outages from the national power grid. Problem. Existing theoretical principles for building microgrids are focused mainly on single-phase distribution networks of low power and do not take into account the features of powerful three-phase industrial microgrids. In particular, the problems of ensuring system stability under conditions of low inertia (absence of rotating masses of generators) and implementing «seamless» transitions between the parallel operation mode with the external grid and the autonomous («island») mode, as well as effective local power balancing taking into account the priority of consumers, remain unresolved. Goal. Development of the principles for building powerful three-phase microgrids capable of providing uninterrupted and high-quality power supply to industrial enterprises with critical energy consumers in conditions of unstable general power supply. Methodology. The study is based on a systematic analysis of international standards and modern publications in the field of microgrids, hierarchical control theory, methods of computer modeling of microgrid modes, as well as on the generalization of experience in designing, installing and long-term (more than one year) experimental and industrial operation of a microgrid with a capacity of more than 1.5 MVA at a real industrial enterprise in Ukraine. Results. Six basic principles for building powerful industrial microgrids have been developed and systematized. The effectiveness of these principles is confirmed by the successful operation of the designed microgrid, which includes a cogeneration unit (up to 1.5 MW), a diesel generator (up to 825 kW), a solar station (72.5 kW), four specialized uninterruptible power supplies with a total capacity of up to 1.95 MW, and an electricity storage unit with a capacity of up to 10 MWh. Scientific novelty. For the first time, the principles for building powerful three-phase industrial microgrids has been developed as a system of six interconnected principles, which, unlike existing approaches, cover the physical aspects of stabilization, system aspects of control and quality aspects of electricity (reactive power compensation, load balancing). The proposed principles are intended for microgrids with a capacity of more than 1 MVA and take into account the specifics of industrial enterprises. Practical value. The proposed principles provide a methodological basis for the design and modernization of powerful industrial microgrids in Ukraine and other countries with unstable power supply. References 36, figures 3.
- Open Access
- 1 July 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Tekhnichna Elektrodynamika
- Vol. 2026 (4) , 51-56
DIRECTIONS FOR DEVELOPMENT OF HIGH-POWER MICROGRIDS FOR INDUSTRIAL ENTERPRISES OF UKRAINE
Research has been conducted into the directions of development of high-power microgrids capable of ensuring the uninterrupted operation of critical electrotechnological equipment at industrial enterprises of Ukraine under unstable external power supply conditions. Improvements to such microgrids are substantiated based on the use of autonomous distributed energy sources and modern technologies for accumulation, storage and conversion of electrical energy parameters, and on the integration of artificial intelligence and energy management methods. The key role of high-power microgrids in ensuring guaranteed power supply to critical energy consumers of industrial enterprises during prolonged outages and unstable external supply conditions has been identified. It is substantiated that the integration of high-power microgrids, modern "smart" mechanism technologies and hybrid energy systems at industrial enterprises increase the energy efficiency of all electrical, technological and organizational processes and their resilience to prolonged outages and external power supply instabilities. The introduction of high-power microgrids at industrial enterprises in Ukraine increases the energy efficiency of all electrotechnologies for the production of critically important products and facilitates the achievement of sustainable development goals. References 19, figure 1.
- 1 July 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Tekhnichna Elektrodynamika
- Vol. 2026 (4) , 51-56
Open AccessDIRECTIONS FOR DEVELOPMENT OF HIGH-POWER MICROGRIDS FOR INDUSTRIAL ENTERPRISES OF UKRAINE
Research has been conducted into the directions of development of high-power microgrids capable of ensuring the uninterrupted operation of critical electrotechnological equipment at industrial enterprises of Ukraine under unstable external power supply conditions. Improvements to such microgrids are substantiated based on the use of autonomous distributed energy sources and modern technologies for accumulation, storage and conversion of electrical energy parameters, and on the integration of artificial intelligence and energy management methods. The key role of high-power microgrids in ensuring guaranteed power supply to critical energy consumers of industrial enterprises during prolonged outages and unstable external supply conditions has been identified. It is substantiated that the integration of high-power microgrids, modern "smart" mechanism technologies and hybrid energy systems at industrial enterprises increase the energy efficiency of all electrical, technological and organizational processes and their resilience to prolonged outages and external power supply instabilities. The introduction of high-power microgrids at industrial enterprises in Ukraine increases the energy efficiency of all electrotechnologies for the production of critically important products and facilitates the achievement of sustainable development goals. References 19, figure 1.
- Open Access
- 30 April 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Tekhnichna Elektrodynamika
- Vol. 2026 (3) , 62-72
THERMAL STABILITY OF UNDERGROUND HIGH-VOLTAGE CABLE LINE UNDER EMERGENCY CONDITIONS OF OVERLOAD AND SHORT CIRCUIT
The paper proposes new knowledge in cable engineering by studying the operation of up-to-date high-voltage cable line under the non-nominal and emergency conditions to ensure its reliability and service life. The temperature conditions for operation of an underground 110 kV three-phase cable line with cross-linked polyethylene insulated cables in the nominal and emergency modes of short circuit and short-term overload of cables are studied by computer finite-element method. A number of practically important problems for designing such cable lines are solved. In particular, the computation of the three-phase short-circuit mode in the line is carried out taking into account its reconnection after short circuit with certain delay time (5, 10 or 15 s) and at different loads (50% and 100% of the nominal current). The results obtained allow determining the permissible operating time for the line operation with the temperature of the cable conductor not higher than the permissible limiting value. The nature of the increase in the temperature of the cables within the time of different current overloads varying from 120% to 200% is investigated. The results give a possibility to determine the permissible operating time of the line when the temperature of the cable conductor does not exceed 130°С. In the case of the double-circuit cable line, the computational results for non-stationary thermal process under emergency condition of one circuit failure and the transmission of double power through the other circuit are presented. It is shown that the limiting conductor temperature of 130°C is reached after 1.3 hours of line operation. The problems solved in the paper answer the questions regarding the thermal stability of the high-voltage cable line in emergency modes and are of interest to designers of such lines as well as organizations responsible for their safe operation and power companies for more efficient use of cable lines. References 36, figures 5, tables 2.
- 30 April 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Tekhnichna Elektrodynamika
- Vol. 2026 (3) , 62-72
Open AccessTHERMAL STABILITY OF UNDERGROUND HIGH-VOLTAGE CABLE LINE UNDER EMERGENCY CONDITIONS OF OVERLOAD AND SHORT CIRCUIT
The paper proposes new knowledge in cable engineering by studying the operation of up-to-date high-voltage cable line under the non-nominal and emergency conditions to ensure its reliability and service life. The temperature conditions for operation of an underground 110 kV three-phase cable line with cross-linked polyethylene insulated cables in the nominal and emergency modes of short circuit and short-term overload of cables are studied by computer finite-element method. A number of practically important problems for designing such cable lines are solved. In particular, the computation of the three-phase short-circuit mode in the line is carried out taking into account its reconnection after short circuit with certain delay time (5, 10 or 15 s) and at different loads (50% and 100% of the nominal current). The results obtained allow determining the permissible operating time for the line operation with the temperature of the cable conductor not higher than the permissible limiting value. The nature of the increase in the temperature of the cables within the time of different current overloads varying from 120% to 200% is investigated. The results give a possibility to determine the permissible operating time of the line when the temperature of the cable conductor does not exceed 130°С. In the case of the double-circuit cable line, the computational results for non-stationary thermal process under emergency condition of one circuit failure and the transmission of double power through the other circuit are presented. It is shown that the limiting conductor temperature of 130°C is reached after 1.3 hours of line operation. The problems solved in the paper answer the questions regarding the thermal stability of the high-voltage cable line in emergency modes and are of interest to designers of such lines as well as organizations responsible for their safe operation and power companies for more efficient use of cable lines. References 36, figures 5, tables 2.
- Open Access
- 9 January 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Tekhnichna Elektrodynamika
- Vol. 2026 (1) , 62-71
MODELING AND ANALYSIS OF LONG-TERM 24-HOUR PROCESSES OF CHANGES IN ELECTRICAL ENERGY FLOWS IN THE MICROGRID OF AN INDUSTRIAL ENTERPRISE
The paper considers the energy strategy for implementing reliable uninterrupted power supply of critically important technological equipment of an industrial enterprise of Ukraine in modern military conditions by creating its industrial microgrid and solving scientific and technical problems regarding the optimal use of its elements and reducing overall costs, which take into account the cost of electricity received from each source of the microgrid. To solve this problem, a computer modeling method was used. It is shown that for modeling long-term (24-hour) electromagnetic processes in a microgrid, it is advisable to use a generalized method for calculating complex currents, which is usually used to calculate sinusoidal current electrical circuits. However, in this task, it is also necessary to take into account that in a microgrid, not only the amplitudes of currents change slowly over time, but also their phases, so it is advisable to use the dynamic phasor method, according to which the calculation is performed simultaneously in the complex and time planes. To implement this method in the Matlab/Simulink package, it is necessary to develop appropriate system models for all power sources and time-varying loads. The paper presents the results of calculating long-term (over a day) active and reactive power flows in the microgrid of a typical industrial enterprise, which contains such power sources as a solar power plant and a cogeneration unit, which can operate both in parallel with the external power grid and without it. The daily costs of electricity obtained from each power source are determined. In order to identify ways to reduce the total cost of electricity, the paper considers various scenarios for connecting power sources and determines their impact on the total daily costs of the enterprise. References 32, figures 8, table 1.
- 9 January 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Tekhnichna Elektrodynamika
- Vol. 2026 (1) , 62-71
Open AccessMODELING AND ANALYSIS OF LONG-TERM 24-HOUR PROCESSES OF CHANGES IN ELECTRICAL ENERGY FLOWS IN THE MICROGRID OF AN INDUSTRIAL ENTERPRISE
The paper considers the energy strategy for implementing reliable uninterrupted power supply of critically important technological equipment of an industrial enterprise of Ukraine in modern military conditions by creating its industrial microgrid and solving scientific and technical problems regarding the optimal use of its elements and reducing overall costs, which take into account the cost of electricity received from each source of the microgrid. To solve this problem, a computer modeling method was used. It is shown that for modeling long-term (24-hour) electromagnetic processes in a microgrid, it is advisable to use a generalized method for calculating complex currents, which is usually used to calculate sinusoidal current electrical circuits. However, in this task, it is also necessary to take into account that in a microgrid, not only the amplitudes of currents change slowly over time, but also their phases, so it is advisable to use the dynamic phasor method, according to which the calculation is performed simultaneously in the complex and time planes. To implement this method in the Matlab/Simulink package, it is necessary to develop appropriate system models for all power sources and time-varying loads. The paper presents the results of calculating long-term (over a day) active and reactive power flows in the microgrid of a typical industrial enterprise, which contains such power sources as a solar power plant and a cogeneration unit, which can operate both in parallel with the external power grid and without it. The daily costs of electricity obtained from each power source are determined. In order to identify ways to reduce the total cost of electricity, the paper considers various scenarios for connecting power sources and determines their impact on the total daily costs of the enterprise. References 32, figures 8, table 1.
- 25 August 2025
- Published by Wroclaw Board of Scientific Technical Societies Federation NOT in Journal of Machine Engineering
- p. 60-69
Magnetophoretic Motion of Micron-Sized Magnetic Particles in the Working Gap of a Magnetic Fluid Seal.
The operational experience of bearing units in technological equipment has been analyzed. The use of magnetic fluid seals to enhance the reliability and failure-free operation of equipment has been justified. A method for expanding the application range of seals by adding micron-sized magnetic particles to the working magnetic fluid, in accordance with Ukrainian Patent No. 106420, has been proposed. The distribution of magnetic induction in the active zone of the seal with an increased gap (0.8 mm) has been calculated for two cases—with and without a defect on the shaft surface. A regime where micron-sized magnetic particles are additionally introduced into the working magnetic fluid has been considered. The non-uniform distribution of the field and the vector quantity of the magnetic force acting on microscopic particles in the magnetic fluid has been demonstrated. The distribution of the velocity of these particles under the influence of this force in the active zone of the seal, both with and without a defect on the shaft, has been obtained through calculations. It has been shown that these particles concentrate in areas with non-uniform fields—in the angular zones of the teeth of the magnetic system and near the defect on the shaft. The characteristic transition time for particles with diameters of d_p=0,1 ;1 and 10 µm is 630, 6.3, and 0.063 minutes, respectively.
- 25 August 2025
- Published by Wroclaw Board of Scientific Technical Societies Federation NOT in Journal of Machine Engineering
- p. 60-69
Magnetophoretic Motion of Micron-Sized Magnetic Particles in the Working Gap of a Magnetic Fluid Seal.
The operational experience of bearing units in technological equipment has been analyzed. The use of magnetic fluid seals to enhance the reliability and failure-free operation of equipment has been justified. A method for expanding the application range of seals by adding micron-sized magnetic particles to the working magnetic fluid, in accordance with Ukrainian Patent No. 106420, has been proposed. The distribution of magnetic induction in the active zone of the seal with an increased gap (0.8 mm) has been calculated for two cases—with and without a defect on the shaft surface. A regime where micron-sized magnetic particles are additionally introduced into the working magnetic fluid has been considered. The non-uniform distribution of the field and the vector quantity of the magnetic force acting on microscopic particles in the magnetic fluid has been demonstrated. The distribution of the velocity of these particles under the influence of this force in the active zone of the seal, both with and without a defect on the shaft, has been obtained through calculations. It has been shown that these particles concentrate in areas with non-uniform fields—in the angular zones of the teeth of the magnetic system and near the defect on the shaft. The characteristic transition time for particles with diameters of d_p=0,1 ;1 and 10 µm is 630, 6.3, and 0.063 minutes, respectively.
- Open Access
- 30 June 2025
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Tekhnichna Elektrodynamika
- Vol. 2025 (4) , 20-28
STABILITY OF POWER CABLES UNDER FIRE CONDITIONS. COMPUTER AND EXPERIMENTAL STUDY
The work is dedicated to the experimental and numerical study of ways to increase the resource and reliability of power cables under fire emergency conditions. Firstly the computer model is developed and the temperature field in XLPE-insulated power cable operating at fire emergency is studied. The thermal processes in the case of the fireproof coating with different thickness located on the central section of the cable around it are analyzed. Two main factors of the additional coating are revealed: 1) the time of stable reliable operation of the cable at fire gradually increases with an increase in the thickness of the coating (a positive factor); 2) under normal operating conditions, due to cooling deterioration, the temperature of the insulation on the section of the cable, corresponding to the coating, increases with an increase in the thickness of the coating (a negative factor). Such factors should be taken into account when applying and choosing the dimensions of the coating. At the second stage of the work, the experimental study of power cable destruction under conditions close to a fire, i.e. under the direct influence of open flame, is carried out. The time from the beginning of the fire, during which the cable under the influence of the flame allows powering the load, is determined. References 17, figures 10.
- 30 June 2025
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Tekhnichna Elektrodynamika
- Vol. 2025 (4) , 20-28
Open AccessSTABILITY OF POWER CABLES UNDER FIRE CONDITIONS. COMPUTER AND EXPERIMENTAL STUDY
The work is dedicated to the experimental and numerical study of ways to increase the resource and reliability of power cables under fire emergency conditions. Firstly the computer model is developed and the temperature field in XLPE-insulated power cable operating at fire emergency is studied. The thermal processes in the case of the fireproof coating with different thickness located on the central section of the cable around it are analyzed. Two main factors of the additional coating are revealed: 1) the time of stable reliable operation of the cable at fire gradually increases with an increase in the thickness of the coating (a positive factor); 2) under normal operating conditions, due to cooling deterioration, the temperature of the insulation on the section of the cable, corresponding to the coating, increases with an increase in the thickness of the coating (a negative factor). Such factors should be taken into account when applying and choosing the dimensions of the coating. At the second stage of the work, the experimental study of power cable destruction under conditions close to a fire, i.e. under the direct influence of open flame, is carried out. The time from the beginning of the fire, during which the cable under the influence of the flame allows powering the load, is determined. References 17, figures 10.
- Open Access
- 15 August 2024
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Tekhnichna Elektrodynamika
- Vol. 2024 (5) , 3-11
ELECTRIC FIELD OF SEMICONDUCTING SCREEN IN POWER CABLE WITH POLYMER INSULATION TAKING INTO ACCOUNT STRUCTURAL INHOMOGENEITIES
The non-homogeneous electric field distributions in the cross-linked polyethylene insulation of 330 kV power cable with multi-conductor core depending on the electrical conductivity and thickness of the semiconducting screen as well as at different frequency of applied voltage (from 50 to 104 Hz) are studied by finite-element analysis. As shown, taking into account the periodic structure of core surface, the electrical conductivity of the material of internal semiconducting screen should exceed 10–6 S/m and its thickness should be at least 1.5 mm in order to obtain the uniform electric field in the basic insulation of the cable at the boundary with the screen. The paper also considers the effect of various types of the surface and volumetric defects in the semiconducting screen on the electric field inhomogeneity in cable insulation. It is shown that the defects in the screen can lead to a significant increase of the electric field in the local zones of their location (up to 5 times as compared to the field without defects) and therefore contribute to the formation and development of treeing structures in the insulation. The revealed results explain the reasons for the micro- and macro-level degradation of power cable insulation and confirm the need to ensure the uniform structure, smooth surface of both semiconducting screen and core during the technological process of manufacturing the power cables with cross-linked polyethylene insulation. References 23, figures 8, table 1.
- 15 August 2024
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Tekhnichna Elektrodynamika
- Vol. 2024 (5) , 3-11
Open AccessELECTRIC FIELD OF SEMICONDUCTING SCREEN IN POWER CABLE WITH POLYMER INSULATION TAKING INTO ACCOUNT STRUCTURAL INHOMOGENEITIES
The non-homogeneous electric field distributions in the cross-linked polyethylene insulation of 330 kV power cable with multi-conductor core depending on the electrical conductivity and thickness of the semiconducting screen as well as at different frequency of applied voltage (from 50 to 104 Hz) are studied by finite-element analysis. As shown, taking into account the periodic structure of core surface, the electrical conductivity of the material of internal semiconducting screen should exceed 10–6 S/m and its thickness should be at least 1.5 mm in order to obtain the uniform electric field in the basic insulation of the cable at the boundary with the screen. The paper also considers the effect of various types of the surface and volumetric defects in the semiconducting screen on the electric field inhomogeneity in cable insulation. It is shown that the defects in the screen can lead to a significant increase of the electric field in the local zones of their location (up to 5 times as compared to the field without defects) and therefore contribute to the formation and development of treeing structures in the insulation. The revealed results explain the reasons for the micro- and macro-level degradation of power cable insulation and confirm the need to ensure the uniform structure, smooth surface of both semiconducting screen and core during the technological process of manufacturing the power cables with cross-linked polyethylene insulation. References 23, figures 8, table 1.
- Open Access
- 1 July 2024
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Tekhnichna Elektrodynamika
- Vol. 2024 (4) , 45-49
COMPUTER AND PHYSICAL SIMULATION OF CAPACITIVE TYPE WIRELESS CHARGER FOR SMALL ELECTRIC VEHICLE
The work considers one of the possible approaches to the creation of a capacitive type wireless charger, which allows for non-contact charging of batteries of small-sized vehicles: electric carts, electric scooters, electric scooters. The basis of the development of such a device is the operation of the hybrid DC-DC converter circuit, which operates at a high frequency (550 kHz), transfers energy to the charging circuit using two capacitive elements and allows receiving a constant regulated voltage on the load, which can be either lower or and more input DC voltage. A prototype of such a device has been developed and the results of its experimental research are given, which confirm the possibility of using this scheme for wireless charging of the battery. A Simulink computer model of such a device has been developed, which takes into account the real values of all parameters of the developed prototype and uses the basic model of a lithium-ion battery. According to the results of the calculations, it was determined that for the developed device of the capacitive type, and the largest losses occur in the inductor coils, the value of efficiency, which characterizes the efficiency of the process of transferring electrical energy from the primary power source to the battery, at the initial stage of its charging (when the parameter of the state of the battery SOC =50%) is 80%. References 10, figures 5.
- 1 July 2024
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Tekhnichna Elektrodynamika
- Vol. 2024 (4) , 45-49
Open AccessCOMPUTER AND PHYSICAL SIMULATION OF CAPACITIVE TYPE WIRELESS CHARGER FOR SMALL ELECTRIC VEHICLE
The work considers one of the possible approaches to the creation of a capacitive type wireless charger, which allows for non-contact charging of batteries of small-sized vehicles: electric carts, electric scooters, electric scooters. The basis of the development of such a device is the operation of the hybrid DC-DC converter circuit, which operates at a high frequency (550 kHz), transfers energy to the charging circuit using two capacitive elements and allows receiving a constant regulated voltage on the load, which can be either lower or and more input DC voltage. A prototype of such a device has been developed and the results of its experimental research are given, which confirm the possibility of using this scheme for wireless charging of the battery. A Simulink computer model of such a device has been developed, which takes into account the real values of all parameters of the developed prototype and uses the basic model of a lithium-ion battery. According to the results of the calculations, it was determined that for the developed device of the capacitive type, and the largest losses occur in the inductor coils, the value of efficiency, which characterizes the efficiency of the process of transferring electrical energy from the primary power source to the battery, at the initial stage of its charging (when the parameter of the state of the battery SOC =50%) is 80%. References 10, figures 5.
- Open Access
- 27 May 2024
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Tekhnichna Elektrodynamika
- Vol. 2024 (3) , 3-11
COMPUTER SIMULATION OF ELECTRICAL PROCESSES WHEN APPEARING PARTIAL DISCHARGES IN MODERN POLYMER INSULATION OF POWER CABLES
A Simulink model of modern polymer insulation of power cables with a spherical gas micro-inclusion, in which high-frequency partial discharges (PDs) occur, has been developed. The magnitude of the voltage both at the beginning of the PD appearance and during its decay was taken into account during numerical calculations and research of such threshold electro-physical processes as PD in solid polymer insulation. The dependence of the voltage drop on the gas micro-inclusion on its size, as well as the time interval between discharges, which is necessary for the formation of free electrons in this gas micro-inclusion, as a necessary condition for the appearance of the next PD, was also taken into account. Based on the results of the calculations, the electro-physical dependences that occur during the PD, such as the influence of the size of the inclusion, the amplitude and frequency of the applied sinusoidal voltage on the above-mentioned characteristics were investigated. It has been revealed that with an increase in the diameter d of a gas microinclusion, such characteristics as the number of discharges per period and the charge of one PD also increase, and this charge increases in proportion to a power function . When the voltage on the cable insulation increases, the number of PDs per period increases, which causes an increase in other characteristics, and when the frequency of the applied voltage increases, the average value of the PDs current increases almost proportionally to the increase in this frequency. Having obtained the results of the calculation of the level of PDs that occur when high-frequency voltage is applied, it is possible to obtain results for the main characteristics of PDs that occur at other frequencies, in particular at the industrial frequency of 50 Hz, which will make it possible to predict the technical condition of the insulation in terms of the residual resource of its trouble-free operation. References 18, figures 6, table 1. Розроблено Simulink-модель сучасної полімерної ізоляції силових кабелів з газовим мікровключенням сферичної форми, в якому виникають високочастотні часткові розряди (ЧР). У процесі чисельних розрахунків та дослідженні таких порогових електрофізичних процесів, як ЧР у твердій полімерній ізоляції, враховувалися величина напруги на початку появи ЧР і за його загасанні, залежність падіння напруги на мікровключенні від його розмірів та тривалість часу між розрядами, необхідна для формування у цьому газовому мікровключенні вільних електронів як необхідної умови для появи наступного ЧР. За результатами проведених розрахунків досліджено такі електрофізичні залежності, що виникають під час протікання ЧР, як вплив розмірів включення, амплітуди та частоти прикладеної синусоїдної напруги на вказані характеристики. Виявлено, що у разі збільшення діаметра d газового мікровключення зростають такі число розрядів за період і величина заряду одного ЧР, причому ця величина зростає пропорційно степеневій функції . Під час підвищення напруги на ізоляції кабелю зростає число ЧР за період, що викликає зростання інших характеристик, а у разі збільшеня частоти прикладеної напруги практично пропорційно зростає середнє значення струму ЧР. Отримуючи результати розрахунку рівня ЧР, що виникають у разі прикладання високочастотної напруги, можна отримувати результати для основних характеристик ЧР, що виникають на інших частотах, зокрема на промисловій частоті 50 Гц, прогнозуючи технічний стан ізоляції щодо залишкової тривалості її безаварійної експлуатації. Бібл. 18, рис. 6, табл. 1.
- 27 May 2024
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Tekhnichna Elektrodynamika
- Vol. 2024 (3) , 3-11
Open AccessCOMPUTER SIMULATION OF ELECTRICAL PROCESSES WHEN APPEARING PARTIAL DISCHARGES IN MODERN POLYMER INSULATION OF POWER CABLES
A Simulink model of modern polymer insulation of power cables with a spherical gas micro-inclusion, in which high-frequency partial discharges (PDs) occur, has been developed. The magnitude of the voltage both at the beginning of the PD appearance and during its decay was taken into account during numerical calculations and research of such threshold electro-physical processes as PD in solid polymer insulation. The dependence of the voltage drop on the gas micro-inclusion on its size, as well as the time interval between discharges, which is necessary for the formation of free electrons in this gas micro-inclusion, as a necessary condition for the appearance of the next PD, was also taken into account. Based on the results of the calculations, the electro-physical dependences that occur during the PD, such as the influence of the size of the inclusion, the amplitude and frequency of the applied sinusoidal voltage on the above-mentioned characteristics were investigated. It has been revealed that with an increase in the diameter d of a gas microinclusion, such characteristics as the number of discharges per period and the charge of one PD also increase, and this charge increases in proportion to a power function . When the voltage on the cable insulation increases, the number of PDs per period increases, which causes an increase in other characteristics, and when the frequency of the applied voltage increases, the average value of the PDs current increases almost proportionally to the increase in this frequency. Having obtained the results of the calculation of the level of PDs that occur when high-frequency voltage is applied, it is possible to obtain results for the main characteristics of PDs that occur at other frequencies, in particular at the industrial frequency of 50 Hz, which will make it possible to predict the technical condition of the insulation in terms of the residual resource of its trouble-free operation. References 18, figures 6, table 1. Розроблено Simulink-модель сучасної полімерної ізоляції силових кабелів з газовим мікровключенням сферичної форми, в якому виникають високочастотні часткові розряди (ЧР). У процесі чисельних розрахунків та дослідженні таких порогових електрофізичних процесів, як ЧР у твердій полімерній ізоляції, враховувалися величина напруги на початку появи ЧР і за його загасанні, залежність падіння напруги на мікровключенні від його розмірів та тривалість часу між розрядами, необхідна для формування у цьому газовому мікровключенні вільних електронів як необхідної умови для появи наступного ЧР. За результатами проведених розрахунків досліджено такі електрофізичні залежності, що виникають під час протікання ЧР, як вплив розмірів включення, амплітуди та частоти прикладеної синусоїдної напруги на вказані характеристики. Виявлено, що у разі збільшення діаметра d газового мікровключення зростають такі число розрядів за період і величина заряду одного ЧР, причому ця величина зростає пропорційно степеневій функції . Під час підвищення напруги на ізоляції кабелю зростає число ЧР за період, що викликає зростання інших характеристик, а у разі збільшеня частоти прикладеної напруги практично пропорційно зростає середнє значення струму ЧР. Отримуючи результати розрахунку рівня ЧР, що виникають у разі прикладання високочастотної напруги, можна отримувати результати для основних характеристик ЧР, що виникають на інших частотах, зокрема на промисловій частоті 50 Гц, прогнозуючи технічний стан ізоляції щодо залишкової тривалості її безаварійної експлуатації. Бібл. 18, рис. 6, табл. 1.