Evgeny Shelekhov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Evgeny Shelekhov has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Anna Borunova
N.N. Semenov Federal Research Center for Chemical Physics of Russian Academy of Sciences, 119334 Moscow, Russia
2 shared publications - Vladimir A. Popov
Department of Physical Metallurgy of Non-Ferrous Metals, National University of Science and Technology “MISiS”, 119049 Moscow, Russia
2 shared publications - Vladimir V. Cheverikin
Department of Physical Metallurgy of Non-Ferrous Metals, National University of Science and Technology “MISiS”, 119049 Moscow, Russia
2 shared publications - Alexey Sergeevich Prosviryakov
National University of Science and Technology MISiS, Moscow, Russia
1 shared publication - Danila V. Matveev
Osipyan Institute of Solid State Physics RAS, 142432 Chernogolovka, Russia
1 shared publication - Ekaterina Vershinina
Mendeleev University of Chemical Technology of Russia, Moscow, Russia
1 shared publication
Latest Publications
- Open Access
- 12 March 2025
- Published by The Royal Society in Royal Society Open Science
- Vol. 12 (3) , 241771
Effect of graphene sheets on the physico-chemical properties of nanocrystallite ceria
Currently, replacing expensive and short-lived materials for supercapacitors based on RuO 2 with more cost-effective and high-performance materials that remain operational after a large number of cycles is a challenge. Cerium-based materials are the most attractive alternative because of cerium’s ability to quickly change oxidation state. This work proposes the synthesis of nanostructured graphene–ceria composite and studies its morphological features arising under the impact of oxygen-free graphene. The mechanism of formation of nano-ceria crystallites when the sol–gel transition occurs on the surface of graphene sheets is also considered. It has been proven that the introduction of 0.5–0.6 wt% graphene sheets into nano-ceria ensures the preservation of its single-phase state, while simultaneously increasing its dispersion. Using the dilatometry method, it has been determined that uniformly distributed sheets of oxygen-free graphene lead to a decrease in temperature of the beginning of composite sintering by 175°C compared with pure nano-ceria and increase the shrinkage value by two times, which, in turn, should promote better sintering. This study fills a gap in the synthesis and characterization of oxygen-free graphene composites, promising raw materials for small devices and large power plants.
- 12 March 2025
- Published by The Royal Society in Royal Society Open Science
- Vol. 12 (3) , 241771
Open AccessEffect of graphene sheets on the physico-chemical properties of nanocrystallite ceria
Currently, replacing expensive and short-lived materials for supercapacitors based on RuO 2 with more cost-effective and high-performance materials that remain operational after a large number of cycles is a challenge. Cerium-based materials are the most attractive alternative because of cerium’s ability to quickly change oxidation state. This work proposes the synthesis of nanostructured graphene–ceria composite and studies its morphological features arising under the impact of oxygen-free graphene. The mechanism of formation of nano-ceria crystallites when the sol–gel transition occurs on the surface of graphene sheets is also considered. It has been proven that the introduction of 0.5–0.6 wt% graphene sheets into nano-ceria ensures the preservation of its single-phase state, while simultaneously increasing its dispersion. Using the dilatometry method, it has been determined that uniformly distributed sheets of oxygen-free graphene lead to a decrease in temperature of the beginning of composite sintering by 175°C compared with pure nano-ceria and increase the shrinkage value by two times, which, in turn, should promote better sintering. This study fills a gap in the synthesis and characterization of oxygen-free graphene composites, promising raw materials for small devices and large power plants.
- 14 January 2025
- Published by Springer Nature in Metallurgist
- Vol. 68 (9) , 1338-1344
Thermal analysis of mechanically activated Cr–B mixture
- 14 January 2025
- Published by Springer Nature in Metallurgist
- Vol. 68 (9) , 1338-1344
Thermal analysis of mechanically activated Cr–B mixture
- Open Access
- 12 December 2022
- Published by MDPI AG in Inventions
- Vol. 7 (4) , 120
Decrease in the Starting Temperature of the Reaction for Fabricating Carbides of Refractory Metals When Using Carbon Nanoparticles as Precursors
Metal matrix composites with a matrix of refractory metals (niobium, tungsten) and reinforcing nanodiamond particles were prepared for studying the possibility of decreasing the starting temperature of carbide synthesis. The size of primary nanodiamond particles was 4–6 nm, but they were combined in large-sized agglomerates. Mechanical alloying was used for producing the composites by crushing agglomerates and distributing nanodiamonds evenly in the metal matrix. The initial and fabricated materials were investigated by X-ray diffraction, differential scanning calorimetry, and transmission and scanning electron microscopy. Thermal processing leads to the reaction for carbide synthesis. Studies have found that the usage of carbon nanoparticles (nanodiamonds) as precursors for fabricating carbides of refractory metals leads to a dramatic decrease in the synthesis temperature in comparison with macro-precursors: lower than 200 °C for tungsten and lower than 350 °C for niobium.
- 12 December 2022
- Published by MDPI AG in Inventions
- Vol. 7 (4) , 120
Open AccessDecrease in the Starting Temperature of the Reaction for Fabricating Carbides of Refractory Metals When Using Carbon Nanoparticles as Precursors
Metal matrix composites with a matrix of refractory metals (niobium, tungsten) and reinforcing nanodiamond particles were prepared for studying the possibility of decreasing the starting temperature of carbide synthesis. The size of primary nanodiamond particles was 4–6 nm, but they were combined in large-sized agglomerates. Mechanical alloying was used for producing the composites by crushing agglomerates and distributing nanodiamonds evenly in the metal matrix. The initial and fabricated materials were investigated by X-ray diffraction, differential scanning calorimetry, and transmission and scanning electron microscopy. Thermal processing leads to the reaction for carbide synthesis. Studies have found that the usage of carbon nanoparticles (nanodiamonds) as precursors for fabricating carbides of refractory metals leads to a dramatic decrease in the synthesis temperature in comparison with macro-precursors: lower than 200 °C for tungsten and lower than 350 °C for niobium.
- Open Access
- 2 September 2022
- Published by MDPI AG in Inventions
- Vol. 7 (3) , 75
Several Aspects of Interaction between Chrome and Nanodiamond Particles in Metal Matrix Composites When Being Heated
The paper considers the development of a technological scheme for preparing metal matrix nanocomposites based on the interaction between nanodiamond reinforcing particles and a chromium matrix when being heated, forming chromium carbide nanoparticles. These carbides are in situ synthesized ceramic reinforcing nanoparticles. The first stage of preparing composites is to obtain composites with the chromium matrix and nanodiamond reinforcing particles. For this purpose, mechanical alloying is used, i.e., processing in planetary mills. The size of a primary nanodiamond particle is 5 nm, but they are combined in agglomerates that are hundreds of micrometers in size. The time of processing in the planetary mill defines the crushing degree of the agglomerates. In this study, processing was carried out for 0.5 h, 2 h, and 4 h. The second stage for obtaining composites with reinforcing particles of chromium carbides is thermal processing. Explorations using the method of differential scanning calorimetry showed that reducing the size of nanodiamond reinforcing particles (by prolonging the time of processing in the planetary mill) leads to a decrease in the initial temperature of the reaction for developing carbides. The worked-out technique for obtaining composites was patented in the Russian Federation (the patent for invention 2772480).
- 2 September 2022
- Published by MDPI AG in Inventions
- Vol. 7 (3) , 75
Open AccessSeveral Aspects of Interaction between Chrome and Nanodiamond Particles in Metal Matrix Composites When Being Heated
The paper considers the development of a technological scheme for preparing metal matrix nanocomposites based on the interaction between nanodiamond reinforcing particles and a chromium matrix when being heated, forming chromium carbide nanoparticles. These carbides are in situ synthesized ceramic reinforcing nanoparticles. The first stage of preparing composites is to obtain composites with the chromium matrix and nanodiamond reinforcing particles. For this purpose, mechanical alloying is used, i.e., processing in planetary mills. The size of a primary nanodiamond particle is 5 nm, but they are combined in agglomerates that are hundreds of micrometers in size. The time of processing in the planetary mill defines the crushing degree of the agglomerates. In this study, processing was carried out for 0.5 h, 2 h, and 4 h. The second stage for obtaining composites with reinforcing particles of chromium carbides is thermal processing. Explorations using the method of differential scanning calorimetry showed that reducing the size of nanodiamond reinforcing particles (by prolonging the time of processing in the planetary mill) leads to a decrease in the initial temperature of the reaction for developing carbides. The worked-out technique for obtaining composites was patented in the Russian Federation (the patent for invention 2772480).