FAFrank Atzler

Frank Atzler

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Frank Atzler has a total of 11 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Methanol With Increased Water Content in Internal Combustion Engines

    by Maximilian Dobberkau, Ronny Werner, Frank Atzler, Johannes Voß

    This paper shows the advantages of methanol as a fuel and compares pure methanol (>99.9%) and methanol with a high‐water content (>18%) for use in an internal combustion engine. 18% water content is representative for methanol synthesized from hydrogen and industrial furnace gases as a carbon dioxide source. The achievable best point indicated efficiency is higher than 43% for both fuels. The increased water content of the low‐purity methanol is compensated by a longer injection time and can approximately be compared to a constant exhaust gas recirculation, which cannot be adjusted to the operating condition. Therefore, the best efficiency operation points are limited to a middle engine speed range and high load, which perfectly fits to a serial hybrid powertrain topology (Range Extender). The paper shows that additional energy that may be required for methanol distillation to high purity can be saved without losing combustion efficiency.

  • Open Access

    The Energy Situation in the Federal Republic of Germany: Analysis of the Current Situation and Perspectives for a Non-Fossil Energy Supply

    by Frank Atzler, Julian Türck, Ralf Türck, Jürgen Krahl

    Formulating energy policies at national, European, and global levels is extremely challenging. The move away from fossil fuels is associated with a variety of technological, economic, and social implications, each of which is subject to dynamic changes and societal scrutiny and can hardly be predicted with certainty. Therefore, a fact-based assessment for the path to a sustainable green energy future is sought out in this paper, using the road-based mobility sector of the Federal Republic of Germany as an example. The analysis performed in this paper is built on publicly accessible, reputable sources like DESTATIS and EUROSTAT. In addition, some very simple calculations were made, e.g., on the potential for wind and photovoltaic energy within Germany. Such an analysis needs to start with the overall energy consumption of any one country. A basic assumption of the paper is that the energy system of the future will be based to a large extent on electricity and its storage in chemical energy. It is assumed that, in addition to hydrogen, liquid energy sources will play a significant role due to the simplicity of their logistics and the subsequent implications on cost. Examples of green, electricity-based fuels with great potential are methanol, methane, and ammonia. Additionally, biomass plays an important role, either for direct use as a fuel or as a source of non-fossil carbon. Today, biofuels, i.e., biodiesel and bioethanol, deliver the largest contribution to climate protection in the EU transport sector. The main goal—the reduction of greenhouse gas emissions—often collides with geopolitical circumstances or national political necessities. This includes, for example, the current world market situation and its national impacts caused by the Russian attack on Ukraine. The prospect for a green, sustainable, and defossilized energy supply are discussed in this context. The paper concludes that a defossilized world energy supply and trade based on renewable electricity and its derivatives, eHydrogen and refuels, and on biomass, is feasible.


  • Open Access

    Potentials of oxymethylene-dimethyl-ether in diesel engine combustion

    by Christopher Saupe, Frank Atzler

    The increasing CO2 concentration in the atmosphere and the resulting climate change require an immediate and efficient reduction of anthropogenic carbon-dioxide emission. This target can be achieved by the usage of CO2-neutral fuels even with current technologies (Schemme et al. in Int J Hydrogen Energy 45:5395–5414, 2020). Diesel engines in particular are amongst the most efficient prime movers. Using oxymethylene-dimethyl-ether (OME) it is possible to solve the hitherto existing Soot-NOx-Trade-off. OME has bounded oxygen in the molecular chain. This reduces the formation of soot, but equally the calorific value. But in considerance of the physical and chemical properties of OME, it could be useful to optimize the standard diesel engine into an OME engine. As a result, single-cylinder tests were performed to obtain a detailed analysis of the differences between OME3-5 and commercially available DIN EN 590 Diesel. Based on the fact that OME has gravimetrically less than half the calorific value of diesel, twice the fuel mass must be injected for the same energy release in the combustion chamber. Therefore, at the beginning of the investigations, a variation of the injector flow rate was carried out by means of different nozzle hole diameters. The evaluation of the results included the fundamental differences in the combustion characteristics of both fuels and the determination of efficiency-increasing potentials in the conversion of OME3-5. Due to the lower ignition delay and the shorter combustion time of OME, potentials in the optimisation of the injection setting became apparent. Higher energy flows over the combustion chamber wall were noticeable in operation with OME. To get to the bottom of this, the single-cylinder investigations were supported by tests on the optically accessible high-pressure chamber and the single-cylinder transparent engine. The optical images showed a narrower cone angle and greater penetration depth of the OME injection jet compared to the diesel injection jet. This confirmed the results from the single-cylinder tests. This provides further potential in the design of the injector nozzle to compensate for these deficits. Overall, this work shows that operation with OME in a classic diesel engine is possible without any significant loss in efficiency and with little effort in the hardware. However, it is also possible to achieve more efficient use of the synthetic fuel with minor adjustments.


  • Multiple injection and rate shaping Part 1: Emissions reduction in passenger car Diesel engines

    by F. Atzler, O. Kastner, R. Rotondi, A. Weigand

    In modern passenger car diesel engines, multiple injection, MI, and rate shaping are measures, which in conjunction with others help to achieve the emissions legislation EU6 and US Tier2 Bin5. However, where hitherto mainly pollutant emissions where considered, CO2 output - i.e. fuel consumption - becomes increasingly important. Also, off cycle emissions may have to be regarded in the future. Additionally engine noise and drivability need consideration. The complexity and effect of an applied injection strategy is defined by the overall engine concept including the after treatment system, and also by the vehicle inertia. Additionally a modern fuel injection system not only has to allow for the necessary injection strategies but at the same time needs to offer robust performance over life time. Although a complex injection system may entail a penalty in cost, this has to be regarded in the context of the complete engine system including a possibly needed exhaust gas after-treatment, since a more expensive injection system can contribute to an overall reduction in cost. A well applied and stable injection system may allow for a simple and cheap after treatment system to be used, optimised for low engine exhaust back pressure. In the present work, the improvements in mixture formation and combustion through multiple injection strategies, MI, and injection rate shaping were investigated. In particular, combination of ramp injection with pilot and post injections were examined. This was done, using a 500 cm3 single cylinder research engine and the Continental directly actuated piezo injector, which allows for the stable application of partial needle lifts for injection rate shaping. The current report provides evidence that appropriate injection patterns in combination with suitable boost andinjection pressures serve to achieve EU6 emissions engineering targets at the investigated operating points. The physio-chemical effects of MI and rate shaping were also analysed by means of 3D combustion simulation, in order to improve the understanding and, hence, facilitate the appropriate application of the injection strategies. A detailed treatise on the computational investigation is provided in Part 2 of this paper (SAE 20009-24-0012).