Jayvant Patil
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Jayvant Patil has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Ahmad Umar
Department of Chemistry, Faculty of Science and Arts, Najran University, Najran, Kingdom of Saudi Arabia
1 shared publication - Digambar Y. Nadargi
Empa, Swiss Federal Laboratories for Materials Science and Technology
1 shared publication - Imtiaz S. Mulla
Former Emeritus Scientist (CSIR), NCL, Pune 411008, India
1 shared publication - Jyoti D. Nadargi
Department of Physics, Santosh Bhimrao Patil College, Solapur, India
1 shared publication - Sharad S. Suryavanshi
School of Physical Sciences, P. A. H. Solapur University, Solapur, India
1 shared publication - Sheikh Ali Akbar
Department of Materials Science and Engineering, The Ohio State University, 140 W 19th Avenue, Columbus, Ohio 43055, The United States
1 shared publication
Latest Publications
- Open Access
- 9 September 2022
- Published by MDPI AG in Chemosensors
- Vol. 10 (9) , 361
Spinel Magnesium Ferrite (MgFe2O4): A Glycine-Assisted Colloidal Combustion and Its Potentiality in Gas-Sensing Application
Herein, we describe the facile synthesis of spinel MgFe2O4 ferrite and its potential use as a gas sensor using a straightforward and reliable sol–gel approach, i.e., the glycine-assisted auto-combustion route. The novelty in obtaining the sensing material via the auto-combustion route is its inherent simplicity and capability to produce the material at an industry scale. The said cost-effective process makes use of simple metal salts (Mg and Fe-nitrates) and glycine in an aqueous solution, which leads to the formation of spinel MgFe2O4 ferrite. A single-phase crystallinity with crystallite sizes ranging between 36 and 41 nm was observed for the synthesized materials using the X-ray diffraction (XRD) technique. The porous morphologies of the synthesized materials caused by auto-ignition during the combustion process were validated by the microscopic investigations. The EDS analysis confirmed the constituted elements such as Mg, Fe, and O, without any impurity peaks. The gas-sensing ability of the synthesized ferrites was examined to detect various reducing gases such as LPG, ethanol, acetone, and ammonia. The ferrite showed the highest response (>80%) toward LPG with the response and recovery times of 15 s and 23 s, respectively. Though the sensor responded low toward ammonia (~30%), its response and recovery times were very quick, i.e., 7 s and 9 s, respectively. The present investigation revealed that the synthesized ferrite materials are good candidates for fabricating high-performance sensors for reducing gases in real-world applications.
- 9 September 2022
- Published by MDPI AG in Chemosensors
- Vol. 10 (9) , 361
Open AccessSpinel Magnesium Ferrite (MgFe2O4): A Glycine-Assisted Colloidal Combustion and Its Potentiality in Gas-Sensing Application
Herein, we describe the facile synthesis of spinel MgFe2O4 ferrite and its potential use as a gas sensor using a straightforward and reliable sol–gel approach, i.e., the glycine-assisted auto-combustion route. The novelty in obtaining the sensing material via the auto-combustion route is its inherent simplicity and capability to produce the material at an industry scale. The said cost-effective process makes use of simple metal salts (Mg and Fe-nitrates) and glycine in an aqueous solution, which leads to the formation of spinel MgFe2O4 ferrite. A single-phase crystallinity with crystallite sizes ranging between 36 and 41 nm was observed for the synthesized materials using the X-ray diffraction (XRD) technique. The porous morphologies of the synthesized materials caused by auto-ignition during the combustion process were validated by the microscopic investigations. The EDS analysis confirmed the constituted elements such as Mg, Fe, and O, without any impurity peaks. The gas-sensing ability of the synthesized ferrites was examined to detect various reducing gases such as LPG, ethanol, acetone, and ammonia. The ferrite showed the highest response (>80%) toward LPG with the response and recovery times of 15 s and 23 s, respectively. Though the sensor responded low toward ammonia (~30%), its response and recovery times were very quick, i.e., 7 s and 9 s, respectively. The present investigation revealed that the synthesized ferrite materials are good candidates for fabricating high-performance sensors for reducing gases in real-world applications.