Mohammed Raffic Noor Mohamed
Mohammed Raffic Noor Mohamed has a total of 45 co-authors. Here are the top co-authors by number of shared publications:
- Balasubramaniyan Karthekeyan Parrthipan
Department of Mechanical Engineering, Kamaraj College of Engineering and Technology, Madurai, India
4 shared publications K. Ganesh Babu
Department of Mechanical Engineering, Chendhuran College of Engineering and Technology, Pudukkottai, India
3 shared publicationsRajasekaran Saminathan
3 shared publications- Selvan Dharani Kumar
Department of Mechanical Engineering, KPR Institute of Engineering and Technology, Coimbatore, India
3 shared publications - Ganesh Babu Karuppiah
Department of Mechanical Engineering, Chendhuran College of Engineering and Technology, India
2 shared publications Haitham Hadidi
Department of Mechanical Engineering, Jazan University, Jazan, Kingdom of Saudi Arabia
2 shared publications
Latest Publications
- 18 August 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 240 (23) , 9735-9761
Optimization of FDM process parameters for ABS components: Effects on printing time, part weight, and vibrational loss factor using Integrated TOPSIS-CoCoSo and decision tree approaches
Fused Deposition Modeling (FDM) has been widely studied for the manufacture of light-weight polymer components. However, the process parameter selection significantly effects the production efficiency, material consumption and vibration damping performance. In the present study, the effects of slice height (0.17–0.33 mm), part density (30%–90%), shell thickness (0.8–2.4 mm), and print speed (50–150 mm/s) on the printing time (PT), part weight (PW), and vibrational loss factor (LF) of Acrylonitrile Butadiene Styrene (ABS) components fabricated through FFF were investigated. Experimental design was done using Taguchi L9 orthogonal array and the results were analyzed by signal to noise ratio analysis. The CRITIC weighting method was coupled with TOPSIS and CoCoSo ranking techniques for multi-criteria optimization and a Decision Tree algorithm was used to determine the most impactful process parameters. The experimental testing outcomes showed a variation in printing time from 34 to 87 min, part weight from 7.85 to 15.78 g and loss factor from 0.044 to 0.143. By CRITIC, the weights of printing time, part weight and loss factor were 29%, 31%, and 40%, respectively, indicating that vibration damping performance was the most important. The results of the TOPSIS and CoCoSo techniques always showed that Trial 8 (0.33 mm slice height, 60% part density, 0.8 mm shell thickness, and 150 mm/s print speed) was the best choice, with a closeness coefficient of 0.9098 and the highest evaluation score. Sensitivity study resulted in a good agreement among the ranking methods with correlation coefficients > 0.95, demonstrating the robustness of the ranking produced. The Decision Tree analysis further confirmed the relevance of the chosen process parameters. The study demonstrates that properly optimized ABS components can simultaneously achieve reduced manufacturing time, controlled material usage and improved vibration damping characteristics, thus making them suitable for passive vibration attenuation applications in automotive, aerospace, electronic housing, and lightweight structural components.
- 18 August 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 240 (23) , 9735-9761
Optimization of FDM process parameters for ABS components: Effects on printing time, part weight, and vibrational loss factor using Integrated TOPSIS-CoCoSo and decision tree approaches
Fused Deposition Modeling (FDM) has been widely studied for the manufacture of light-weight polymer components. However, the process parameter selection significantly effects the production efficiency, material consumption and vibration damping performance. In the present study, the effects of slice height (0.17–0.33 mm), part density (30%–90%), shell thickness (0.8–2.4 mm), and print speed (50–150 mm/s) on the printing time (PT), part weight (PW), and vibrational loss factor (LF) of Acrylonitrile Butadiene Styrene (ABS) components fabricated through FFF were investigated. Experimental design was done using Taguchi L9 orthogonal array and the results were analyzed by signal to noise ratio analysis. The CRITIC weighting method was coupled with TOPSIS and CoCoSo ranking techniques for multi-criteria optimization and a Decision Tree algorithm was used to determine the most impactful process parameters. The experimental testing outcomes showed a variation in printing time from 34 to 87 min, part weight from 7.85 to 15.78 g and loss factor from 0.044 to 0.143. By CRITIC, the weights of printing time, part weight and loss factor were 29%, 31%, and 40%, respectively, indicating that vibration damping performance was the most important. The results of the TOPSIS and CoCoSo techniques always showed that Trial 8 (0.33 mm slice height, 60% part density, 0.8 mm shell thickness, and 150 mm/s print speed) was the best choice, with a closeness coefficient of 0.9098 and the highest evaluation score. Sensitivity study resulted in a good agreement among the ranking methods with correlation coefficients > 0.95, demonstrating the robustness of the ranking produced. The Decision Tree analysis further confirmed the relevance of the chosen process parameters. The study demonstrates that properly optimized ABS components can simultaneously achieve reduced manufacturing time, controlled material usage and improved vibration damping characteristics, thus making them suitable for passive vibration attenuation applications in automotive, aerospace, electronic housing, and lightweight structural components.
- 3 August 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 240 (21) , 8711-8729
A multi-criteria decision-making and machine learning approach to predict the tribological behavior of microwave-sintered Ti-0.8Ni–0.3Mo/X wt.% TiB composites
This paper investigates the tribological behavior of microwave-sintered Ti-0.8Ni–0.3Mo/X wt.% TiB composites using an integrated Multi-Criteria Decision-Making (MCDM) and Machine Learning (ML) approach. It explores the relationship between composition and tribological properties. Criteria Importance Through Intercriteria Correlation (CRITIC) and entropy methods were used to determine criteria weights, revealing wear rate as more influential than friction. Weighted Aggregated Sum Product Assessment (WASPAS) ranked alternatives based on input factors, and various ML algorithms—Decision Tree, Random Forest, Linear Regression, and AdaBoost—were trained to predict the MCDM-derived closeness coefficient. Among these, AdaBoost showed superior performance. The study confirms the accuracy of ML models in predicting wear and friction under varying conditions, highlighting their reliability in optimizing composite performance. This approach effectively supports tribological evaluation and materials design for engineering applications.
- 3 August 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 240 (21) , 8711-8729
A multi-criteria decision-making and machine learning approach to predict the tribological behavior of microwave-sintered Ti-0.8Ni–0.3Mo/X wt.% TiB composites
This paper investigates the tribological behavior of microwave-sintered Ti-0.8Ni–0.3Mo/X wt.% TiB composites using an integrated Multi-Criteria Decision-Making (MCDM) and Machine Learning (ML) approach. It explores the relationship between composition and tribological properties. Criteria Importance Through Intercriteria Correlation (CRITIC) and entropy methods were used to determine criteria weights, revealing wear rate as more influential than friction. Weighted Aggregated Sum Product Assessment (WASPAS) ranked alternatives based on input factors, and various ML algorithms—Decision Tree, Random Forest, Linear Regression, and AdaBoost—were trained to predict the MCDM-derived closeness coefficient. Among these, AdaBoost showed superior performance. The study confirms the accuracy of ML models in predicting wear and friction under varying conditions, highlighting their reliability in optimizing composite performance. This approach effectively supports tribological evaluation and materials design for engineering applications.
- 8 July 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 240 (20) , 8216-8235
Multi-objective optimization of tribocorrosion parameters and biocompatibility of selective laser melted CoCr alloy
This study investigated the biocompatibility and wear behaviour of cobalt chromium (CoCr) alloy fabricated using selective laser melting (SLM). A combination of Taguchi L 16 experimental design and multi-criteria decision making (MCDM) methods was employed to analyze the effects of wear parameters, such as load, speed, and time. Optimization was performed with respect to the weighting of criteria using a method based on the removal effect of criteria (MEREC) and multi-attribute border approximation area comparison (MABAC) for ranking the alternatives. The findings indicated that the 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) assay on MG-63 osteoblast-like cells showed excellent cell viability, confirming the biocompatibility of the 3D-printed CoCr alloy. Antibacterial tests indicated a cell viability of 83.4% on the alloy, leading to a stable Cr 2 O 3 passive oxide layer, confirming its suitability for implants. Subsequently, the wear parameter was augmented, and an analysis of variance (ANOVA) was performed to determine the most influential parameter in the wear behaviour at a confidence interval of 95%. The optimal process parameters that enhanced the biological and tribological characteristics of the 3D-printed alloy were a load of 20 N, speed of 600 rpm, and time of 45 min (Trial 2). These resulted in a minimum wear rate of 1.16 × 10 −6 mm 3 /Nm, friction force of 3 N, coefficient of friction (CoF) of 0.05, and average surface roughness of 1.88 µm. The improvements in the wear rate, friction force, CoF, and surface roughness were 12.2%, 13.04%, 12.5%, and 7.84%, respectively, when compared to the worst parameter (Trial 12). Also, the low current density (I) over the potential voltage (V) indicating corrosion resistance was in electrochemical corrosion testing. Wear analyses showed that ploughing tracks, grooves due to adhesive wear, and subsurface crack initiation due to fatigue were induced on the worn surface. This combined biological and tribological assessment provides significant insights for the design and optimization of implants.
- 8 July 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 240 (20) , 8216-8235
Multi-objective optimization of tribocorrosion parameters and biocompatibility of selective laser melted CoCr alloy
This study investigated the biocompatibility and wear behaviour of cobalt chromium (CoCr) alloy fabricated using selective laser melting (SLM). A combination of Taguchi L 16 experimental design and multi-criteria decision making (MCDM) methods was employed to analyze the effects of wear parameters, such as load, speed, and time. Optimization was performed with respect to the weighting of criteria using a method based on the removal effect of criteria (MEREC) and multi-attribute border approximation area comparison (MABAC) for ranking the alternatives. The findings indicated that the 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) assay on MG-63 osteoblast-like cells showed excellent cell viability, confirming the biocompatibility of the 3D-printed CoCr alloy. Antibacterial tests indicated a cell viability of 83.4% on the alloy, leading to a stable Cr 2 O 3 passive oxide layer, confirming its suitability for implants. Subsequently, the wear parameter was augmented, and an analysis of variance (ANOVA) was performed to determine the most influential parameter in the wear behaviour at a confidence interval of 95%. The optimal process parameters that enhanced the biological and tribological characteristics of the 3D-printed alloy were a load of 20 N, speed of 600 rpm, and time of 45 min (Trial 2). These resulted in a minimum wear rate of 1.16 × 10 −6 mm 3 /Nm, friction force of 3 N, coefficient of friction (CoF) of 0.05, and average surface roughness of 1.88 µm. The improvements in the wear rate, friction force, CoF, and surface roughness were 12.2%, 13.04%, 12.5%, and 7.84%, respectively, when compared to the worst parameter (Trial 12). Also, the low current density (I) over the potential voltage (V) indicating corrosion resistance was in electrochemical corrosion testing. Wear analyses showed that ploughing tracks, grooves due to adhesive wear, and subsurface crack initiation due to fatigue were induced on the worn surface. This combined biological and tribological assessment provides significant insights for the design and optimization of implants.
- 20 May 2026
- Published by SAGE Publications in Journal of Composite Materials
Investigation of tribological behaviour of B 4 C–graphene glass fiber composites using Taguchi, multi-criteria decision making, and machine learning approaches
The current research has focused on developing epoxy-based glass fiber composites reinforced with boron carbide (B 4 C) and graphene (Gr) particles processed through a compression moulding process for enhanced tribological performance. Through Taguchi’s L 32 experimental design, the experimental layout has been prepared by varying material configuration, sliding speed, normal load, and sliding time to observe their effect on wear rate and coefficient of friction. To address the multi-response problem, criteria weighting have been evaluated through Shannon’s entropy and CRITIC techniques integrated with TOPSIS and CoCoSo MCDM methods. Both methods have identified the optimal condition for minimizing wear and CoF as the hybrid filler composite tested at 600 rpm, 20 N, and 4 min. Sensitivity analysis across the four weighting combinations indicated a strong correlation (≈0.9) between the CRITIC TOPSIS and CRITIC CoCoSo rankings. Multivariate ANOVA has ensured and emphasized the strong interaction of material configuration and speed over both the responses studied. The AdaBoost algorithm has exhibited superior predictive accuracy, with an R 2 of 0.99 among the machine learning models. SEM analysis revealed fiber breakage, matrix cracking, void formation, and debris formation. The findings establish the potential of composites developed with hybrid fillers for applications demanding good tribological performance.
- 20 May 2026
- Published by SAGE Publications in Journal of Composite Materials
Investigation of tribological behaviour of B 4 C–graphene glass fiber composites using Taguchi, multi-criteria decision making, and machine learning approaches
The current research has focused on developing epoxy-based glass fiber composites reinforced with boron carbide (B 4 C) and graphene (Gr) particles processed through a compression moulding process for enhanced tribological performance. Through Taguchi’s L 32 experimental design, the experimental layout has been prepared by varying material configuration, sliding speed, normal load, and sliding time to observe their effect on wear rate and coefficient of friction. To address the multi-response problem, criteria weighting have been evaluated through Shannon’s entropy and CRITIC techniques integrated with TOPSIS and CoCoSo MCDM methods. Both methods have identified the optimal condition for minimizing wear and CoF as the hybrid filler composite tested at 600 rpm, 20 N, and 4 min. Sensitivity analysis across the four weighting combinations indicated a strong correlation (≈0.9) between the CRITIC TOPSIS and CRITIC CoCoSo rankings. Multivariate ANOVA has ensured and emphasized the strong interaction of material configuration and speed over both the responses studied. The AdaBoost algorithm has exhibited superior predictive accuracy, with an R 2 of 0.99 among the machine learning models. SEM analysis revealed fiber breakage, matrix cracking, void formation, and debris formation. The findings establish the potential of composites developed with hybrid fillers for applications demanding good tribological performance.
- 18 March 2026
- Published by SAGE Publications in Journal of Thermoplastic Composite Materials
- Vol. 39 (10) , 5942-5977
Machine learning enabled CRITIC–CoCoSO optimization of PVA/CSP/AgNPs films for multifunctional packaging applications
The current research has proposed an innovative methodology to enhance PVA/CSP/AgNPs hybrid biocomposite films by integrating the CRITIC and CoCoSo multi-criteria decision-making (MCDM) frameworks with machine learning techniques. Bio composite films can be used in medicine, packaging, and environmental applications. The biocomposite films were developed by mixing polyvinyl alcohol (PVA), coconut shell powder (CSP), and silver nanoparticles (AgNPs) to attain better mechanical, thermal, and antibacterial properties. The experimental design comprises 25 distinct trials to assess the tensile strength (TS), Young’s Modulus (YM), percentage elongation (%E), and maximum degradation temperature (T) of the fabricated composite films. CRITIC method was adopted to evaluate the weights of the criteria in an unbiased way, and CoCoSo technique ranked the alternatives. The results were analyzed using supervised machine learning algorithms, including Random Forest, Neural Network, Linear Regression, and AdaBoost. AdaBoost algorithm demonstrated superior performance with an R 2 value greater than 0.98 for all output responses. Decision tree analysis revealed that the composition of silver nitrate significantly influences tensile strength, while coconut shell powder affects Young’s modulus. The optimized film, composed of PVA/20%CSP/4 mM AgNPs, exhibited improved UV-shielding, reduced water absorption (26.2%), and decreased soil weight loss (41.4%). SEM images confirmed the uniform dispersion of AgNPs within the PVA matrix. The integration of CRITIC-CoCoSo with machine learning provides a scalable approach for designing multifunctional bio-composites with enhanced properties for sustainable applications.
- 18 March 2026
- Published by SAGE Publications in Journal of Thermoplastic Composite Materials
- Vol. 39 (10) , 5942-5977
Machine learning enabled CRITIC–CoCoSO optimization of PVA/CSP/AgNPs films for multifunctional packaging applications
The current research has proposed an innovative methodology to enhance PVA/CSP/AgNPs hybrid biocomposite films by integrating the CRITIC and CoCoSo multi-criteria decision-making (MCDM) frameworks with machine learning techniques. Bio composite films can be used in medicine, packaging, and environmental applications. The biocomposite films were developed by mixing polyvinyl alcohol (PVA), coconut shell powder (CSP), and silver nanoparticles (AgNPs) to attain better mechanical, thermal, and antibacterial properties. The experimental design comprises 25 distinct trials to assess the tensile strength (TS), Young’s Modulus (YM), percentage elongation (%E), and maximum degradation temperature (T) of the fabricated composite films. CRITIC method was adopted to evaluate the weights of the criteria in an unbiased way, and CoCoSo technique ranked the alternatives. The results were analyzed using supervised machine learning algorithms, including Random Forest, Neural Network, Linear Regression, and AdaBoost. AdaBoost algorithm demonstrated superior performance with an R 2 value greater than 0.98 for all output responses. Decision tree analysis revealed that the composition of silver nitrate significantly influences tensile strength, while coconut shell powder affects Young’s modulus. The optimized film, composed of PVA/20%CSP/4 mM AgNPs, exhibited improved UV-shielding, reduced water absorption (26.2%), and decreased soil weight loss (41.4%). SEM images confirmed the uniform dispersion of AgNPs within the PVA matrix. The integration of CRITIC-CoCoSo with machine learning provides a scalable approach for designing multifunctional bio-composites with enhanced properties for sustainable applications.
- 19 January 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
- Vol. 239 (3) , 617-637
On search of optimal FDM parameter settings for reduced dimensional error using entropy-PCA-TOPSIS and regression machine learning techniques
Fused deposition modeling (FDM) is a fascinating additive manufacturing technique that has the potential to create prototypes and industrial-grade parts from thermoplastic filaments processed through the extrusion technique. Higher processing time, poor surface finish, and low dimensional accuracy are the major barriers to adopting this technique on a wider scale in industries. The current research has focused on identifying the optimal factor settings for minimizing the dimensional deviations in a simple cuboid model with a circular hole at the center. The study has considered six different FDM factors, such as layer thickness, extrusion temperature, print bed temperature, print speed, raster angle, and part orientation, to understand its impact on errors in dimensional attributes such as length, width, thickness, and hole diameter for nylon filament reinforced with aramid fibers at 8% composition. The measured values are further analyzed for international tolerance (IT) grades, length, and width, resulting in IT08 to IT14, thickness, and hole diameter tolerance grade values ranging from IT09 to IT14. Entropy and principal component analysis methods have been deployed for criteria weight evaluation, and different weight values have been assigned to the experimental outcomes. Technique for Order of Preference by Similarity to Ideal Solution (TOPSIS) based ranking of alternatives correlates 72.34% (Entropy vs Principal component analysis), with the worst ranked alternative as similar. Regression models developed have R-sq values of 98.15%, 86.27%, 97.63%, and 99.96% for accurately predicting length, width, thickness, and hole diameter changes, respectively. Adaboost algorithm outperformed in training and testing closeness coefficient values with superior performance at all the considered split ratios. The decision tree structure developed indicates layer thickness is significant over the change in length, part orientation has significance over the change in width and hole diameter, and raster angle is significant towards thickness, respectively. Field emission scanning electron microscope (FESEM) images ensure the presence of pores and partially solidified material in the printed samples.
- 19 January 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
- Vol. 239 (3) , 617-637
On search of optimal FDM parameter settings for reduced dimensional error using entropy-PCA-TOPSIS and regression machine learning techniques
Fused deposition modeling (FDM) is a fascinating additive manufacturing technique that has the potential to create prototypes and industrial-grade parts from thermoplastic filaments processed through the extrusion technique. Higher processing time, poor surface finish, and low dimensional accuracy are the major barriers to adopting this technique on a wider scale in industries. The current research has focused on identifying the optimal factor settings for minimizing the dimensional deviations in a simple cuboid model with a circular hole at the center. The study has considered six different FDM factors, such as layer thickness, extrusion temperature, print bed temperature, print speed, raster angle, and part orientation, to understand its impact on errors in dimensional attributes such as length, width, thickness, and hole diameter for nylon filament reinforced with aramid fibers at 8% composition. The measured values are further analyzed for international tolerance (IT) grades, length, and width, resulting in IT08 to IT14, thickness, and hole diameter tolerance grade values ranging from IT09 to IT14. Entropy and principal component analysis methods have been deployed for criteria weight evaluation, and different weight values have been assigned to the experimental outcomes. Technique for Order of Preference by Similarity to Ideal Solution (TOPSIS) based ranking of alternatives correlates 72.34% (Entropy vs Principal component analysis), with the worst ranked alternative as similar. Regression models developed have R-sq values of 98.15%, 86.27%, 97.63%, and 99.96% for accurately predicting length, width, thickness, and hole diameter changes, respectively. Adaboost algorithm outperformed in training and testing closeness coefficient values with superior performance at all the considered split ratios. The decision tree structure developed indicates layer thickness is significant over the change in length, part orientation has significance over the change in width and hole diameter, and raster angle is significant towards thickness, respectively. Field emission scanning electron microscope (FESEM) images ensure the presence of pores and partially solidified material in the printed samples.
- 1 December 2024
- Published by Taylor & Francis in Journal of Adhesion Science and Technology
- Vol. 39 (6) , 879-909
Effects of multi-objective optimization of friction stir welding process parameter on mechanical and ballistic properties of AA5754 aluminum alloy
- 1 December 2024
- Published by Taylor & Francis in Journal of Adhesion Science and Technology
- Vol. 39 (6) , 879-909
Effects of multi-objective optimization of friction stir welding process parameter on mechanical and ballistic properties of AA5754 aluminum alloy
- Open Access
- 1 October 2024
- Published by IOP Publishing in Materials Research Express
- Vol. 11 (10) , 106520
Tensile strength prediction in monel 400 weldments using classification and regression algorithms in machine learning
Selecting the most effective welding settings impacts mechanical strength and weld quality, with parameters like current, voltage, and speed playing pivotal roles. The mechanical part encompasses material properties, welding process variables, and structural integrity, all contributing to the overall weld quality and strength. By integrating these mechanical factors with predictive modelling, a comprehensive understanding of weld performance can be achieved, enabling optimized welding settings and enhanced weld quality assurance. This study assesses and compares machine learning algorithms such as a random tree, random forest, and C4.5 to determine their predictive capability regarding the tensile strength in Monel 400 Weldments. By utilizing a dataset comprising 32 instances with attributes like Current, Voltage, and Speed, models were developed and assessed using K-Fold cross-validation. Among these algorithms, the random tree models emerge as the most proficient in accurately predicting the tensile strength for Monel 400 Weldments through classification ML techniques. Similarly, regression algorithms have been deployed to assess the dataset by varying the train-test split ratio and gradient boosting, which exhibited superior performance with a higher R2 value of 0.99. Both random tree and Gradient boosting algorithms have commonly been recommended, with current being the most influential factor affecting tensile strength.
- 1 October 2024
- Published by IOP Publishing in Materials Research Express
- Vol. 11 (10) , 106520
Open AccessTensile strength prediction in monel 400 weldments using classification and regression algorithms in machine learning
Selecting the most effective welding settings impacts mechanical strength and weld quality, with parameters like current, voltage, and speed playing pivotal roles. The mechanical part encompasses material properties, welding process variables, and structural integrity, all contributing to the overall weld quality and strength. By integrating these mechanical factors with predictive modelling, a comprehensive understanding of weld performance can be achieved, enabling optimized welding settings and enhanced weld quality assurance. This study assesses and compares machine learning algorithms such as a random tree, random forest, and C4.5 to determine their predictive capability regarding the tensile strength in Monel 400 Weldments. By utilizing a dataset comprising 32 instances with attributes like Current, Voltage, and Speed, models were developed and assessed using K-Fold cross-validation. Among these algorithms, the random tree models emerge as the most proficient in accurately predicting the tensile strength for Monel 400 Weldments through classification ML techniques. Similarly, regression algorithms have been deployed to assess the dataset by varying the train-test split ratio and gradient boosting, which exhibited superior performance with a higher R2 value of 0.99. Both random tree and Gradient boosting algorithms have commonly been recommended, with current being the most influential factor affecting tensile strength.