Balasubramaniyan Karthekeyan Parrthipan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Balasubramaniyan Karthekeyan Parrthipan has a total of 46 co-authors. Here are the top co-authors by number of shared publications:
- Pandiyarajan Narayanasamy
Department of Mechanical Engineering , Kamaraj College of Engineering and Technology , Near Virudhunagar , Madurai , Tamil Nadu , India
7 shared publications - Mohammed Raffic Noor Mohamed
Department of Aeronautical Engineering, Nehru Institute of Technology, Coimbatore, Tamil Nadu, India
4 shared publications - Pandiarajan Balasundar
Department of Mechatronics Engineering, Kamaraj College of Engineering and Technology, Near Virudhunagar, Madurai, Tamil Nadu, India
3 shared publications Pratheesh Krishnankutty
Engineering Department, College of Engineering and Technology, University of Technology and Applied Sciences, Muscat, Oman
3 shared publications- Thulasiram Ramkumar
Department of Mechanical Engineering, Dr Mahalingam College of Engineering and Technology, Pollachi, India
3 shared publications Mohammed Raffic Noor Mohamed
Department of Aeronautical Engineering, Nehru Institute of Technology, Coimbatore, India
2 shared publications
Latest Publications
- 18 August 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 240 (23) , 9735-9761
Optimization of FDM process parameters for ABS components: Effects on printing time, part weight, and vibrational loss factor using Integrated TOPSIS-CoCoSo and decision tree approaches
Fused Deposition Modeling (FDM) has been widely studied for the manufacture of light-weight polymer components. However, the process parameter selection significantly effects the production efficiency, material consumption and vibration damping performance. In the present study, the effects of slice height (0.17–0.33 mm), part density (30%–90%), shell thickness (0.8–2.4 mm), and print speed (50–150 mm/s) on the printing time (PT), part weight (PW), and vibrational loss factor (LF) of Acrylonitrile Butadiene Styrene (ABS) components fabricated through FFF were investigated. Experimental design was done using Taguchi L9 orthogonal array and the results were analyzed by signal to noise ratio analysis. The CRITIC weighting method was coupled with TOPSIS and CoCoSo ranking techniques for multi-criteria optimization and a Decision Tree algorithm was used to determine the most impactful process parameters. The experimental testing outcomes showed a variation in printing time from 34 to 87 min, part weight from 7.85 to 15.78 g and loss factor from 0.044 to 0.143. By CRITIC, the weights of printing time, part weight and loss factor were 29%, 31%, and 40%, respectively, indicating that vibration damping performance was the most important. The results of the TOPSIS and CoCoSo techniques always showed that Trial 8 (0.33 mm slice height, 60% part density, 0.8 mm shell thickness, and 150 mm/s print speed) was the best choice, with a closeness coefficient of 0.9098 and the highest evaluation score. Sensitivity study resulted in a good agreement among the ranking methods with correlation coefficients > 0.95, demonstrating the robustness of the ranking produced. The Decision Tree analysis further confirmed the relevance of the chosen process parameters. The study demonstrates that properly optimized ABS components can simultaneously achieve reduced manufacturing time, controlled material usage and improved vibration damping characteristics, thus making them suitable for passive vibration attenuation applications in automotive, aerospace, electronic housing, and lightweight structural components.
- 18 August 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 240 (23) , 9735-9761
Optimization of FDM process parameters for ABS components: Effects on printing time, part weight, and vibrational loss factor using Integrated TOPSIS-CoCoSo and decision tree approaches
Fused Deposition Modeling (FDM) has been widely studied for the manufacture of light-weight polymer components. However, the process parameter selection significantly effects the production efficiency, material consumption and vibration damping performance. In the present study, the effects of slice height (0.17–0.33 mm), part density (30%–90%), shell thickness (0.8–2.4 mm), and print speed (50–150 mm/s) on the printing time (PT), part weight (PW), and vibrational loss factor (LF) of Acrylonitrile Butadiene Styrene (ABS) components fabricated through FFF were investigated. Experimental design was done using Taguchi L9 orthogonal array and the results were analyzed by signal to noise ratio analysis. The CRITIC weighting method was coupled with TOPSIS and CoCoSo ranking techniques for multi-criteria optimization and a Decision Tree algorithm was used to determine the most impactful process parameters. The experimental testing outcomes showed a variation in printing time from 34 to 87 min, part weight from 7.85 to 15.78 g and loss factor from 0.044 to 0.143. By CRITIC, the weights of printing time, part weight and loss factor were 29%, 31%, and 40%, respectively, indicating that vibration damping performance was the most important. The results of the TOPSIS and CoCoSo techniques always showed that Trial 8 (0.33 mm slice height, 60% part density, 0.8 mm shell thickness, and 150 mm/s print speed) was the best choice, with a closeness coefficient of 0.9098 and the highest evaluation score. Sensitivity study resulted in a good agreement among the ranking methods with correlation coefficients > 0.95, demonstrating the robustness of the ranking produced. The Decision Tree analysis further confirmed the relevance of the chosen process parameters. The study demonstrates that properly optimized ABS components can simultaneously achieve reduced manufacturing time, controlled material usage and improved vibration damping characteristics, thus making them suitable for passive vibration attenuation applications in automotive, aerospace, electronic housing, and lightweight structural components.
- 3 August 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 240 (21) , 8711-8729
A multi-criteria decision-making and machine learning approach to predict the tribological behavior of microwave-sintered Ti-0.8Ni–0.3Mo/X wt.% TiB composites
This paper investigates the tribological behavior of microwave-sintered Ti-0.8Ni–0.3Mo/X wt.% TiB composites using an integrated Multi-Criteria Decision-Making (MCDM) and Machine Learning (ML) approach. It explores the relationship between composition and tribological properties. Criteria Importance Through Intercriteria Correlation (CRITIC) and entropy methods were used to determine criteria weights, revealing wear rate as more influential than friction. Weighted Aggregated Sum Product Assessment (WASPAS) ranked alternatives based on input factors, and various ML algorithms—Decision Tree, Random Forest, Linear Regression, and AdaBoost—were trained to predict the MCDM-derived closeness coefficient. Among these, AdaBoost showed superior performance. The study confirms the accuracy of ML models in predicting wear and friction under varying conditions, highlighting their reliability in optimizing composite performance. This approach effectively supports tribological evaluation and materials design for engineering applications.
- 3 August 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 240 (21) , 8711-8729
A multi-criteria decision-making and machine learning approach to predict the tribological behavior of microwave-sintered Ti-0.8Ni–0.3Mo/X wt.% TiB composites
This paper investigates the tribological behavior of microwave-sintered Ti-0.8Ni–0.3Mo/X wt.% TiB composites using an integrated Multi-Criteria Decision-Making (MCDM) and Machine Learning (ML) approach. It explores the relationship between composition and tribological properties. Criteria Importance Through Intercriteria Correlation (CRITIC) and entropy methods were used to determine criteria weights, revealing wear rate as more influential than friction. Weighted Aggregated Sum Product Assessment (WASPAS) ranked alternatives based on input factors, and various ML algorithms—Decision Tree, Random Forest, Linear Regression, and AdaBoost—were trained to predict the MCDM-derived closeness coefficient. Among these, AdaBoost showed superior performance. The study confirms the accuracy of ML models in predicting wear and friction under varying conditions, highlighting their reliability in optimizing composite performance. This approach effectively supports tribological evaluation and materials design for engineering applications.
- 10 November 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (13) , 12735-12747
Microstructure Evaluation and Fatigue Properties of Automated DC Pulsed MIG Welding of Monel 400
- 10 November 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (13) , 12735-12747
Microstructure Evaluation and Fatigue Properties of Automated DC Pulsed MIG Welding of Monel 400
- 27 August 2025
- Published by SAGE Publications in Journal of Thermoplastic Composite Materials
PVA/CSP/AgNPs hybrid biocomposite films: Optimization of process constraints using Taguchi-based grey relational analysis and functional property evaluation
Polyvinyl alcohol (PVA)-based hybrid biocomposite films were developed using coconut shell powder (CSP, 5–25 wt.%) as an organic filler and silver nanoparticles (AgNPs, 1–5 mM) as an inorganic filler. The films were fabricated by molding a homogeneous PVA/CSP/AgNPs solution in Petri dishes, and their mechanical and thermal properties were evaluated according to ASTM standards. The synthesis process and the contributions of CSP and AgNPs for enhanced mechanical and thermal stability were analyzed using the Taguchi-based Grey Relational Analysis (GRA) technique. Tensile strength, Young’s modulus, elongation at break, and maximum degradation temperature were assessed using an L25 orthogonal array. Grey regression analysis identified the optimal film composition as 10% CSP and 1 mM AgNPs, which achieved a tensile strength of 38.1 MPa, Young’s modulus of 92.3 MPa, an elongation at break of 18.1%, and a maximum degradation temperature of 315°C. ANOVA indicated that AgNPs and CSP contributed 50.46% and 41.58%, respectively, to overall performance. FTIR, XRD, TGA, and SEM analyses revealed enhanced matrix-filler compatibility, increased crystallinity (23.4%), uniform dispersion of fillers, and improved thermal stability in the optimal film. UV transmittance and water absorption were reduced by 45% and 56.7%, respectively, compared to pure PVA films. Soil burial tests indicated slower degradation of the optimal film due to reduced moisture absorption. The results highlight the suitability of PVA/10%CSP/1 mM AgNPs films for packaging applications, owing to their superior mechanical, thermal, water barrier, UV barrier, and biodegradability properties. The Taguchi-based GRA technique effectively optimized filler combinations for improved performance.
- 27 August 2025
- Published by SAGE Publications in Journal of Thermoplastic Composite Materials
PVA/CSP/AgNPs hybrid biocomposite films: Optimization of process constraints using Taguchi-based grey relational analysis and functional property evaluation
Polyvinyl alcohol (PVA)-based hybrid biocomposite films were developed using coconut shell powder (CSP, 5–25 wt.%) as an organic filler and silver nanoparticles (AgNPs, 1–5 mM) as an inorganic filler. The films were fabricated by molding a homogeneous PVA/CSP/AgNPs solution in Petri dishes, and their mechanical and thermal properties were evaluated according to ASTM standards. The synthesis process and the contributions of CSP and AgNPs for enhanced mechanical and thermal stability were analyzed using the Taguchi-based Grey Relational Analysis (GRA) technique. Tensile strength, Young’s modulus, elongation at break, and maximum degradation temperature were assessed using an L25 orthogonal array. Grey regression analysis identified the optimal film composition as 10% CSP and 1 mM AgNPs, which achieved a tensile strength of 38.1 MPa, Young’s modulus of 92.3 MPa, an elongation at break of 18.1%, and a maximum degradation temperature of 315°C. ANOVA indicated that AgNPs and CSP contributed 50.46% and 41.58%, respectively, to overall performance. FTIR, XRD, TGA, and SEM analyses revealed enhanced matrix-filler compatibility, increased crystallinity (23.4%), uniform dispersion of fillers, and improved thermal stability in the optimal film. UV transmittance and water absorption were reduced by 45% and 56.7%, respectively, compared to pure PVA films. Soil burial tests indicated slower degradation of the optimal film due to reduced moisture absorption. The results highlight the suitability of PVA/10%CSP/1 mM AgNPs films for packaging applications, owing to their superior mechanical, thermal, water barrier, UV barrier, and biodegradability properties. The Taguchi-based GRA technique effectively optimized filler combinations for improved performance.
- 2 August 2025
- Published by Wiley in Polymer Composites
- Vol. 47 (2) , 1523-1537
Enhancement of the Functional Properties of Vinyl Ester Composites Using Alkali‐Treated Cocos nucifera Shell Biochar for Sustainable Applications
The objective of this study is to enhance the mechanical, thermal, dielectric, and functional characteristics of vinyl ester composites by adding environmentally friendly alkali‐treated Cocos nucifera shell (CNS) biochar for high‐performance, sustainable material applications. Six combinations of composite plates were prepared by incorporating 5%, 10%, and 15% of untreated and alkali‐treated CNS biochar into a vinyl ester matrix using the solution casting technique. Alkali treatment improves the surface structure of CNS biochar through the removal of non‐cellulosic components and enhanced compatibility and bonding. FTIR analysis verifies structural changes, and XRD analysis indicates enhanced crystallinity (34%–49%) and crystallite size (15–27 nm) with the elimination of amorphous parts. The fabricated composites are thermally stable up to 558°C with a residual mass of 16.45% and 23.25% for 15% untreated and alkali‐treated biochar composites, respectively. DSC analysis reveals a rise in glass transition temperature (156°C–164.8°C) and degradation temperature (255.54°C–263.76°C) for alkali‐treated CNS biochar‐loaded vinyl ester composites. A greater storage modulus ( E ′) of 17,445 Pa reflects enhanced load transfer. Water uptake is higher with CNS biochar content, up to 5.5% for VE/15% CNS composites, but decreases with alkali‐treated composites by stripping off polar groups. The water contact angle (WCA) of VE/15% CNS and VE/15% at‐CNS composites are 98.6° and 123.4°, respectively, which ensures the hydrophobicity. Alkali‐treated CNS biochar also increases the dielectric constant of vinyl ester composites via charge accumulation and polarization, enhancing charge storage and minimizing energy loss.
- 2 August 2025
- Published by Wiley in Polymer Composites
- Vol. 47 (2) , 1523-1537
Enhancement of the Functional Properties of Vinyl Ester Composites Using Alkali‐Treated Cocos nucifera Shell Biochar for Sustainable Applications
The objective of this study is to enhance the mechanical, thermal, dielectric, and functional characteristics of vinyl ester composites by adding environmentally friendly alkali‐treated Cocos nucifera shell (CNS) biochar for high‐performance, sustainable material applications. Six combinations of composite plates were prepared by incorporating 5%, 10%, and 15% of untreated and alkali‐treated CNS biochar into a vinyl ester matrix using the solution casting technique. Alkali treatment improves the surface structure of CNS biochar through the removal of non‐cellulosic components and enhanced compatibility and bonding. FTIR analysis verifies structural changes, and XRD analysis indicates enhanced crystallinity (34%–49%) and crystallite size (15–27 nm) with the elimination of amorphous parts. The fabricated composites are thermally stable up to 558°C with a residual mass of 16.45% and 23.25% for 15% untreated and alkali‐treated biochar composites, respectively. DSC analysis reveals a rise in glass transition temperature (156°C–164.8°C) and degradation temperature (255.54°C–263.76°C) for alkali‐treated CNS biochar‐loaded vinyl ester composites. A greater storage modulus ( E ′) of 17,445 Pa reflects enhanced load transfer. Water uptake is higher with CNS biochar content, up to 5.5% for VE/15% CNS composites, but decreases with alkali‐treated composites by stripping off polar groups. The water contact angle (WCA) of VE/15% CNS and VE/15% at‐CNS composites are 98.6° and 123.4°, respectively, which ensures the hydrophobicity. Alkali‐treated CNS biochar also increases the dielectric constant of vinyl ester composites via charge accumulation and polarization, enhancing charge storage and minimizing energy loss.
- 19 January 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
- Vol. 239 (3) , 617-637
On search of optimal FDM parameter settings for reduced dimensional error using entropy-PCA-TOPSIS and regression machine learning techniques
Fused deposition modeling (FDM) is a fascinating additive manufacturing technique that has the potential to create prototypes and industrial-grade parts from thermoplastic filaments processed through the extrusion technique. Higher processing time, poor surface finish, and low dimensional accuracy are the major barriers to adopting this technique on a wider scale in industries. The current research has focused on identifying the optimal factor settings for minimizing the dimensional deviations in a simple cuboid model with a circular hole at the center. The study has considered six different FDM factors, such as layer thickness, extrusion temperature, print bed temperature, print speed, raster angle, and part orientation, to understand its impact on errors in dimensional attributes such as length, width, thickness, and hole diameter for nylon filament reinforced with aramid fibers at 8% composition. The measured values are further analyzed for international tolerance (IT) grades, length, and width, resulting in IT08 to IT14, thickness, and hole diameter tolerance grade values ranging from IT09 to IT14. Entropy and principal component analysis methods have been deployed for criteria weight evaluation, and different weight values have been assigned to the experimental outcomes. Technique for Order of Preference by Similarity to Ideal Solution (TOPSIS) based ranking of alternatives correlates 72.34% (Entropy vs Principal component analysis), with the worst ranked alternative as similar. Regression models developed have R-sq values of 98.15%, 86.27%, 97.63%, and 99.96% for accurately predicting length, width, thickness, and hole diameter changes, respectively. Adaboost algorithm outperformed in training and testing closeness coefficient values with superior performance at all the considered split ratios. The decision tree structure developed indicates layer thickness is significant over the change in length, part orientation has significance over the change in width and hole diameter, and raster angle is significant towards thickness, respectively. Field emission scanning electron microscope (FESEM) images ensure the presence of pores and partially solidified material in the printed samples.
- 19 January 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
- Vol. 239 (3) , 617-637
On search of optimal FDM parameter settings for reduced dimensional error using entropy-PCA-TOPSIS and regression machine learning techniques
Fused deposition modeling (FDM) is a fascinating additive manufacturing technique that has the potential to create prototypes and industrial-grade parts from thermoplastic filaments processed through the extrusion technique. Higher processing time, poor surface finish, and low dimensional accuracy are the major barriers to adopting this technique on a wider scale in industries. The current research has focused on identifying the optimal factor settings for minimizing the dimensional deviations in a simple cuboid model with a circular hole at the center. The study has considered six different FDM factors, such as layer thickness, extrusion temperature, print bed temperature, print speed, raster angle, and part orientation, to understand its impact on errors in dimensional attributes such as length, width, thickness, and hole diameter for nylon filament reinforced with aramid fibers at 8% composition. The measured values are further analyzed for international tolerance (IT) grades, length, and width, resulting in IT08 to IT14, thickness, and hole diameter tolerance grade values ranging from IT09 to IT14. Entropy and principal component analysis methods have been deployed for criteria weight evaluation, and different weight values have been assigned to the experimental outcomes. Technique for Order of Preference by Similarity to Ideal Solution (TOPSIS) based ranking of alternatives correlates 72.34% (Entropy vs Principal component analysis), with the worst ranked alternative as similar. Regression models developed have R-sq values of 98.15%, 86.27%, 97.63%, and 99.96% for accurately predicting length, width, thickness, and hole diameter changes, respectively. Adaboost algorithm outperformed in training and testing closeness coefficient values with superior performance at all the considered split ratios. The decision tree structure developed indicates layer thickness is significant over the change in length, part orientation has significance over the change in width and hole diameter, and raster angle is significant towards thickness, respectively. Field emission scanning electron microscope (FESEM) images ensure the presence of pores and partially solidified material in the printed samples.
- Open Access
- 1 January 2025
- Published by BOHR Publishers
- Vol. 2 (1) , 30-34
Experimental investigation on mechanical properties of post-weld heat-treated Inconel 718/316L dissimilar TIG weldments
Dissimilar welding of nickel-based superalloys with austenitic stainless steels is crucial for the development of advanced engineering systems operating under extreme temperature and mechanical load conditions. This study reports the welding of Inconel 718 to AISI 316L stainless steel by means of continuous current Tungsten Inert Gas (TIG) welding and ERNiCrMo-4 as the filler metal. The influence of post-weld heat treatment (PWHT) on the mechanical properties of the joint has been investigated. PWHT was conducted by heating the samples to 450◦C, 650◦C, and 850◦C for 2 h in a controlled furnace and then cooling them in the air. We examined the microhardness changes in the base metal, heat-affected zone, and fusion zone (FZ), and also the tensile properties at room temperature according to ASTM standards. The welded joint had a peak FZ hardness of nearly 220 HV and a very low ductility of 9.6%. The FZ was about 23% harder due to the strengthening of Inconel 718 by precipitation after PWHT at 650◦C, but softening occurred at 850◦C due to over-aging and coarser phases. Although the ductility dropped as a result of the above, the material after PWHT at 850◦C exhibited the highest tensile strength (416 MPa) and elongation (37.8%), which are more than 300% higher than the welded state.
- 1 January 2025
- Published by BOHR Publishers
- Vol. 2 (1) , 30-34
Open AccessExperimental investigation on mechanical properties of post-weld heat-treated Inconel 718/316L dissimilar TIG weldments
Dissimilar welding of nickel-based superalloys with austenitic stainless steels is crucial for the development of advanced engineering systems operating under extreme temperature and mechanical load conditions. This study reports the welding of Inconel 718 to AISI 316L stainless steel by means of continuous current Tungsten Inert Gas (TIG) welding and ERNiCrMo-4 as the filler metal. The influence of post-weld heat treatment (PWHT) on the mechanical properties of the joint has been investigated. PWHT was conducted by heating the samples to 450◦C, 650◦C, and 850◦C for 2 h in a controlled furnace and then cooling them in the air. We examined the microhardness changes in the base metal, heat-affected zone, and fusion zone (FZ), and also the tensile properties at room temperature according to ASTM standards. The welded joint had a peak FZ hardness of nearly 220 HV and a very low ductility of 9.6%. The FZ was about 23% harder due to the strengthening of Inconel 718 by precipitation after PWHT at 650◦C, but softening occurred at 850◦C due to over-aging and coarser phases. Although the ductility dropped as a result of the above, the material after PWHT at 850◦C exhibited the highest tensile strength (416 MPa) and elongation (37.8%), which are more than 300% higher than the welded state.
- Open Access
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 30
Optimizing mechanical properties of concrete with waste ceramic tiles and coconut shell charcoal as fine aggregate replacements: A Taguchi approach
This study explores the potential use of leftover ceramic tiles and coconut shell charcoal as substitutes for fine particles in concrete. Five different mixtures were tested under different water/cement proportions by replacing different amounts of M Sand with waste ceramic tiles and coconut shell charcoal. These mixtures were M1 (100% M), M2 (90% M + 5% T + 5% C), M3 (80% M + 10% T + 10% C), M4 (70% M + 15% T + 15% C), and M5 (60% M + 20% T + 20% C) under different water/cement (0.45, 0.46, 0.47, 0.48, and 0.49). Using an L25 orthogonal array designed with Minitab software, the Taguchi-based grey relational analysis method was used to optimize the mechanical properties of the concrete mix. The results of the experiment showed that adding waste ceramic tiles and coconut shell charcoal enhanced the sustainability of concrete production while lowering reliance on natural resources, and the best mix designs were found. This study shows that recycling waste materials into high-performance concrete is feasible and has the potential to be a sustainable building material. The findings not only address waste management issues but also offer a way forward toward resource-efficient and ecologically friendly concrete production.
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 30
Open AccessOptimizing mechanical properties of concrete with waste ceramic tiles and coconut shell charcoal as fine aggregate replacements: A Taguchi approach
This study explores the potential use of leftover ceramic tiles and coconut shell charcoal as substitutes for fine particles in concrete. Five different mixtures were tested under different water/cement proportions by replacing different amounts of M Sand with waste ceramic tiles and coconut shell charcoal. These mixtures were M1 (100% M), M2 (90% M + 5% T + 5% C), M3 (80% M + 10% T + 10% C), M4 (70% M + 15% T + 15% C), and M5 (60% M + 20% T + 20% C) under different water/cement (0.45, 0.46, 0.47, 0.48, and 0.49). Using an L25 orthogonal array designed with Minitab software, the Taguchi-based grey relational analysis method was used to optimize the mechanical properties of the concrete mix. The results of the experiment showed that adding waste ceramic tiles and coconut shell charcoal enhanced the sustainability of concrete production while lowering reliance on natural resources, and the best mix designs were found. This study shows that recycling waste materials into high-performance concrete is feasible and has the potential to be a sustainable building material. The findings not only address waste management issues but also offer a way forward toward resource-efficient and ecologically friendly concrete production.
- Open Access
- 1 October 2024
- Published by IOP Publishing in Materials Research Express
- Vol. 11 (10) , 106520
Tensile strength prediction in monel 400 weldments using classification and regression algorithms in machine learning
Selecting the most effective welding settings impacts mechanical strength and weld quality, with parameters like current, voltage, and speed playing pivotal roles. The mechanical part encompasses material properties, welding process variables, and structural integrity, all contributing to the overall weld quality and strength. By integrating these mechanical factors with predictive modelling, a comprehensive understanding of weld performance can be achieved, enabling optimized welding settings and enhanced weld quality assurance. This study assesses and compares machine learning algorithms such as a random tree, random forest, and C4.5 to determine their predictive capability regarding the tensile strength in Monel 400 Weldments. By utilizing a dataset comprising 32 instances with attributes like Current, Voltage, and Speed, models were developed and assessed using K-Fold cross-validation. Among these algorithms, the random tree models emerge as the most proficient in accurately predicting the tensile strength for Monel 400 Weldments through classification ML techniques. Similarly, regression algorithms have been deployed to assess the dataset by varying the train-test split ratio and gradient boosting, which exhibited superior performance with a higher R2 value of 0.99. Both random tree and Gradient boosting algorithms have commonly been recommended, with current being the most influential factor affecting tensile strength.
- 1 October 2024
- Published by IOP Publishing in Materials Research Express
- Vol. 11 (10) , 106520
Open AccessTensile strength prediction in monel 400 weldments using classification and regression algorithms in machine learning
Selecting the most effective welding settings impacts mechanical strength and weld quality, with parameters like current, voltage, and speed playing pivotal roles. The mechanical part encompasses material properties, welding process variables, and structural integrity, all contributing to the overall weld quality and strength. By integrating these mechanical factors with predictive modelling, a comprehensive understanding of weld performance can be achieved, enabling optimized welding settings and enhanced weld quality assurance. This study assesses and compares machine learning algorithms such as a random tree, random forest, and C4.5 to determine their predictive capability regarding the tensile strength in Monel 400 Weldments. By utilizing a dataset comprising 32 instances with attributes like Current, Voltage, and Speed, models were developed and assessed using K-Fold cross-validation. Among these algorithms, the random tree models emerge as the most proficient in accurately predicting the tensile strength for Monel 400 Weldments through classification ML techniques. Similarly, regression algorithms have been deployed to assess the dataset by varying the train-test split ratio and gradient boosting, which exhibited superior performance with a higher R2 value of 0.99. Both random tree and Gradient boosting algorithms have commonly been recommended, with current being the most influential factor affecting tensile strength.