Berkay Karacor
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Berkay Karacor has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Mustafa Ozcanli
Cukurova Universitesi
13 shared publications Mustafa Ozcanli
Department of Automotive Engineering, Çukurova University, Adana, Turkey
3 shared publications- Abdulkadir Yaşar
Cukurova Universitesi
2 shared publications Hasan Serin
Çukurova University
2 shared publications- Bekir Ender Bağ
Cukurova Universitesi
1 shared publication Fatma Nur Kocabuğa
Çukurova University
1 shared publication
Latest Publications
- Open Access
- 9 October 2026
- Published by IOP Publishing in Materials Research Express
- Vol. 13 (19) , 195304
Valorization of agricultural residues as reinforcement in polymer matrix composites: a comparative study
In this study, polyester and vinyl ester resins were used as matrix materials, while pine root, cotton waste, and corn stalk waste were selected as reinforcement materials. The effects of combining these wastes at different reinforcement ratios on the thermal and mechanical performance of the composite samples were investigated. Composite test specimens were produced using the open molding method with agricultural waste reinforcement at 2.5%, 5%, and 10% by weight. Hardness and tensile tests were applied to determine the mechanical properties of the obtained specimens, while thermal conductivity measurements were performed to determine their thermal behavior. The findings showed that the vinyl ester matrix composite specimen with 2.5% corn stalk waste filling exhibited the highest tensile strength, while the polyester matrix composite specimen with 10% cotton stalk waste filling showed the lowest strength. Similarly, the polyester matrix composite specimen with 2.5% cotton stalk waste filling had the highest hardness value in the hardness tests, while the polyester matrix composite specimen with 10% pine root waste filling had the lowest value. In thermal conductivity tests, the highest thermal conductivity value was measured in the vinyl ester matrix composite sample filled with 2.5% corn waste, while the lowest value was measured in the polyester matrix composite sample filled with 2.5% pine root waste. In conclusion, it has been shown that environmentally friendly and sustainable composite materials can be obtained by integrating agricultural wastes into polymer matrix composites, and that this will provide an innovative and alternative contribution to fields such as automotive, insulation, and construction applications.
- 9 October 2026
- Published by IOP Publishing in Materials Research Express
- Vol. 13 (19) , 195304
Open AccessValorization of agricultural residues as reinforcement in polymer matrix composites: a comparative study
In this study, polyester and vinyl ester resins were used as matrix materials, while pine root, cotton waste, and corn stalk waste were selected as reinforcement materials. The effects of combining these wastes at different reinforcement ratios on the thermal and mechanical performance of the composite samples were investigated. Composite test specimens were produced using the open molding method with agricultural waste reinforcement at 2.5%, 5%, and 10% by weight. Hardness and tensile tests were applied to determine the mechanical properties of the obtained specimens, while thermal conductivity measurements were performed to determine their thermal behavior. The findings showed that the vinyl ester matrix composite specimen with 2.5% corn stalk waste filling exhibited the highest tensile strength, while the polyester matrix composite specimen with 10% cotton stalk waste filling showed the lowest strength. Similarly, the polyester matrix composite specimen with 2.5% cotton stalk waste filling had the highest hardness value in the hardness tests, while the polyester matrix composite specimen with 10% pine root waste filling had the lowest value. In thermal conductivity tests, the highest thermal conductivity value was measured in the vinyl ester matrix composite sample filled with 2.5% corn waste, while the lowest value was measured in the polyester matrix composite sample filled with 2.5% pine root waste. In conclusion, it has been shown that environmentally friendly and sustainable composite materials can be obtained by integrating agricultural wastes into polymer matrix composites, and that this will provide an innovative and alternative contribution to fields such as automotive, insulation, and construction applications.
- 1 June 2026
- Published by Kocaeli Journal of Science and Engineering in Kocaeli Journal of Science and Engineering
- Vol. 2026 (17) , 161-170
Excavator Bucket Design with Different Steel Materials: Topology Optimization and Cost Analysis
Topology optimization is a type of analysis that aims to reduce the weight of a design operating under specific load and boundary conditions, and it achieves this by optimizing the results. In this study, topology optimization was performed on an excavator bucket to reduce the weight of the material through design changes, and the results were compared with two different materials. Since the design obtained as a result of topology optimization is not a realistic excavator bucket design, the visuals are only used as a reference in the new design. In this study, a new design with reduced weight and almost the same strength was obtained as a result of topology optimization. The designs before and after the analysis were created using the computer-aided software. The analyses were performed using the finite element analysis software. During the analysis, Hardox 450 and St-37 materials were used. During optimization, total deformation, equivalent stress safety factors, and costs were compared. As a result of the study, similar values to those obtained in the first model were obtained for stress, deformation and safety factor values in the new design, achieving a 28.9% reduction in weight.
- 1 June 2026
- Published by Kocaeli Journal of Science and Engineering in Kocaeli Journal of Science and Engineering
- Vol. 2026 (17) , 161-170
Excavator Bucket Design with Different Steel Materials: Topology Optimization and Cost Analysis
Topology optimization is a type of analysis that aims to reduce the weight of a design operating under specific load and boundary conditions, and it achieves this by optimizing the results. In this study, topology optimization was performed on an excavator bucket to reduce the weight of the material through design changes, and the results were compared with two different materials. Since the design obtained as a result of topology optimization is not a realistic excavator bucket design, the visuals are only used as a reference in the new design. In this study, a new design with reduced weight and almost the same strength was obtained as a result of topology optimization. The designs before and after the analysis were created using the computer-aided software. The analyses were performed using the finite element analysis software. During the analysis, Hardox 450 and St-37 materials were used. During optimization, total deformation, equivalent stress safety factors, and costs were compared. As a result of the study, similar values to those obtained in the first model were obtained for stress, deformation and safety factor values in the new design, achieving a 28.9% reduction in weight.
- 5 May 2026
- Published by Springer Nature in Iranian Polymer Journal
- Vol. 35 (10) , 1-20
Hemp seed oil-based bio-composites as a sustainable alternative for automotive interior applications
- 5 May 2026
- Published by Springer Nature in Iranian Polymer Journal
- Vol. 35 (10) , 1-20
Hemp seed oil-based bio-composites as a sustainable alternative for automotive interior applications
- 27 March 2026
- Published by Anadolu Universitesi Bilim ve Teknoloji Dergisi-A: Uygulamali Bilimler ve Muhendislik in Eskişehir Technical University Journal of Science and Technology A - Applied Sciences and Engineering
- Vol. 27 (1) , 39-62
SUSTAINABLE COMPOSITES: INVESTIGATION OF OLIVE SEED AND BASIL LEAF POWDER MATERIALS
In this study, biocomposite materials resistant to various effects (heat and humidity) were produced by using olive seed powder and basil leaf powder as reinforcing elements at different ratios (30%-0%, 25%-5%, 20%-10%, 15%-15%, 10%-20%, 5%-25%, 0%-30%) and the effects of these ratios were obtained as a result of tests. In the samples produced using olive kernel powder and basil leaf powder, it was observed that the powder ratio added to the mixture had significant effects on the properties in tensile, impact, hardness, water absorption, and ignition loss tests. In the tensile strength test, the sample produced using 30% olive pomace powder showed the highest tensile strength with 28.892 MPa, while a value of 23.39 MPa was observed with 30% basil leaf powder. In the impact energy test, the BLP5 sample produced using 5% basil leaf powder had the highest resistance with 0.808 J. In the Vickers hardness test, the BLP30 sample with 30% basil leaf powder reached the highest value (150.4 HV) among the samples produced using basil leaf powder, while the BLP0 sample produced using olive pomace powder with the same 30% pomace powder ratio reached 120.11 HV. In the water absorption test, a decrease in water absorption capacity was observed as the basil leaf powder ratio increased and the lowest absorption capacity was observed in BLP30 specimen produced using 30% basil leaf powder. However, it was observed that the specimens produced using olive seed powder by weight had less water absorption capacity than the specimens produced using basil leaf powder by weight. In the ignition loss test, the weight loss increased with higher olive seed or basil leaf powder content, reflecting the greater organic fraction in these samples. Based on these results, it is aimed to be used in the automotive sector in areas where water and heat contact is high.
- 27 March 2026
- Published by Anadolu Universitesi Bilim ve Teknoloji Dergisi-A: Uygulamali Bilimler ve Muhendislik in Eskişehir Technical University Journal of Science and Technology A - Applied Sciences and Engineering
- Vol. 27 (1) , 39-62
SUSTAINABLE COMPOSITES: INVESTIGATION OF OLIVE SEED AND BASIL LEAF POWDER MATERIALS
In this study, biocomposite materials resistant to various effects (heat and humidity) were produced by using olive seed powder and basil leaf powder as reinforcing elements at different ratios (30%-0%, 25%-5%, 20%-10%, 15%-15%, 10%-20%, 5%-25%, 0%-30%) and the effects of these ratios were obtained as a result of tests. In the samples produced using olive kernel powder and basil leaf powder, it was observed that the powder ratio added to the mixture had significant effects on the properties in tensile, impact, hardness, water absorption, and ignition loss tests. In the tensile strength test, the sample produced using 30% olive pomace powder showed the highest tensile strength with 28.892 MPa, while a value of 23.39 MPa was observed with 30% basil leaf powder. In the impact energy test, the BLP5 sample produced using 5% basil leaf powder had the highest resistance with 0.808 J. In the Vickers hardness test, the BLP30 sample with 30% basil leaf powder reached the highest value (150.4 HV) among the samples produced using basil leaf powder, while the BLP0 sample produced using olive pomace powder with the same 30% pomace powder ratio reached 120.11 HV. In the water absorption test, a decrease in water absorption capacity was observed as the basil leaf powder ratio increased and the lowest absorption capacity was observed in BLP30 specimen produced using 30% basil leaf powder. However, it was observed that the specimens produced using olive seed powder by weight had less water absorption capacity than the specimens produced using basil leaf powder by weight. In the ignition loss test, the weight loss increased with higher olive seed or basil leaf powder content, reflecting the greater organic fraction in these samples. Based on these results, it is aimed to be used in the automotive sector in areas where water and heat contact is high.
- Open Access
- 3 March 2025
- Published by Kahramanmaras Sutcu Imam University Journal of Engineering Sciences in Kahramanmaraş Sütçü İmam Üniversitesi Mühendislik Bilimleri Dergisi
- Vol. 28 (1) , 216-229
FINITE ELEMENT ANALYSIS OF EXCAVATOR BUCKET DESIGN WITH BIOMIMETIC APPROACH WITH DIFFERENT STEELS
One of the biggest problems of construction machines that make people's lives easier is digging efficiency. In this study, a new excavator teeth model with a biomimetic approach was developed to solve the problem of digging efficiency. This biomimetic digging teeth model is inspired by the front claw of the armadillo, which is naturally a successful digging animal. In the bucket, only the teeth are biomimetic and in the armadillo teeth model, the 5 mm deep thinned parts on the sides of the standard bucket are determined as 25 mm deep in the armadillo teeth model for extra lightness. In addition, a standard digging tooth was designed and finite element analysis of this standard design and the armadillo design was carried out using different steels. The designs were created using the CATIA V5 R21 program. The analyzes were carried out using the Ansys Workbench 18.1 program. Three different steel groups were used for the analysis results. These were St-37, S690QL, and Weldox900 E steels. Total deformation, safety factor, equivalent stress, and cost analysis were carried out. The average stress values were 228.85 MPa for the standard teeth and 162.01 MPa for the armadillo teeth.
- 3 March 2025
- Published by Kahramanmaras Sutcu Imam University Journal of Engineering Sciences in Kahramanmaraş Sütçü İmam Üniversitesi Mühendislik Bilimleri Dergisi
- Vol. 28 (1) , 216-229
Open AccessFINITE ELEMENT ANALYSIS OF EXCAVATOR BUCKET DESIGN WITH BIOMIMETIC APPROACH WITH DIFFERENT STEELS
One of the biggest problems of construction machines that make people's lives easier is digging efficiency. In this study, a new excavator teeth model with a biomimetic approach was developed to solve the problem of digging efficiency. This biomimetic digging teeth model is inspired by the front claw of the armadillo, which is naturally a successful digging animal. In the bucket, only the teeth are biomimetic and in the armadillo teeth model, the 5 mm deep thinned parts on the sides of the standard bucket are determined as 25 mm deep in the armadillo teeth model for extra lightness. In addition, a standard digging tooth was designed and finite element analysis of this standard design and the armadillo design was carried out using different steels. The designs were created using the CATIA V5 R21 program. The analyzes were carried out using the Ansys Workbench 18.1 program. Three different steel groups were used for the analysis results. These were St-37, S690QL, and Weldox900 E steels. Total deformation, safety factor, equivalent stress, and cost analysis were carried out. The average stress values were 228.85 MPa for the standard teeth and 162.01 MPa for the armadillo teeth.
- Open Access
- 1 January 2025
- Published by Afyon Kocatepe Universitesi Fen Ve Muhendislik Bilimleri Dergisi in Afyon Kocatepe University Journal of Sciences and Engineering
- Vol. 25 (6) , 1470-1480
A Thermal Analysis Study: Investigation of Different Materials in Three Different Piston Head Designs
In this study, the effects of using different materials in different piston head designs for internal combustion engines on the thermal performance of the piston heads were analyzed. Three different piston head models were created using the CAD/CAM software CATIA V5 R21 and thermal analysis were performed in ANSYS Workbench. The designs were evaluated using Al 6061 and AlSiC materials to investigate the temperature distribution and heat flux performance. The analysis results showed significant differences between the two materials. Based on the results of piston head designs 1, 2, and 3, AlSiC showed superior performance due to its high thermal conductivity and temperature resistance. In the results, piston head design 2 with AlSiC showed higher performance than Al 6061 with a maximum heat flux of 8.21 x105 W/m in piston 2 head design. However, Al 6061 offers advantages in terms of lower cost and ease of manufacture. Among the three piston head designs, piston head 2 was characterized by a balanced temperature distribution (min. 456.75°C, max. 500°C) and superior thermal performance. When using AlSiC, the maximum heat flux of 8.21 x105 W/m² compared to 8.15 x 105 W/m2 for Al 6061 showed improved thermal conductivity, resulting in exceptional stability against high temperature fluctuations
- 1 January 2025
- Published by Afyon Kocatepe Universitesi Fen Ve Muhendislik Bilimleri Dergisi in Afyon Kocatepe University Journal of Sciences and Engineering
- Vol. 25 (6) , 1470-1480
Open AccessA Thermal Analysis Study: Investigation of Different Materials in Three Different Piston Head Designs
In this study, the effects of using different materials in different piston head designs for internal combustion engines on the thermal performance of the piston heads were analyzed. Three different piston head models were created using the CAD/CAM software CATIA V5 R21 and thermal analysis were performed in ANSYS Workbench. The designs were evaluated using Al 6061 and AlSiC materials to investigate the temperature distribution and heat flux performance. The analysis results showed significant differences between the two materials. Based on the results of piston head designs 1, 2, and 3, AlSiC showed superior performance due to its high thermal conductivity and temperature resistance. In the results, piston head design 2 with AlSiC showed higher performance than Al 6061 with a maximum heat flux of 8.21 x105 W/m in piston 2 head design. However, Al 6061 offers advantages in terms of lower cost and ease of manufacture. Among the three piston head designs, piston head 2 was characterized by a balanced temperature distribution (min. 456.75°C, max. 500°C) and superior thermal performance. When using AlSiC, the maximum heat flux of 8.21 x105 W/m² compared to 8.15 x 105 W/m2 for Al 6061 showed improved thermal conductivity, resulting in exceptional stability against high temperature fluctuations
- 26 December 2024
- Published by Wiley in Polymer Composites
- Vol. 46 (8) , 7091-7107
The use of bioresin composites created with five different vegetable oils such as soybean oil, palm oil, rapeseed oil, cottonseed oil, linseed oil in the automotive industry
In this study, novel bioresin was prepared together with epoxy resin with five different plant oils such as soybean oil, palm oil, rapeseed oil, cottonseed oil, and flaxseed oil. The samples were formed by adding jute/flax intraply fiber to the bioresin formed by adding these vegetable oils to the epoxy at 10%, 20%, 30%, and 40%. While producing these composites, vacuum assisted resin transfer molding method was preferred. Tensile, flexural, impact test, thermogravimetric and differential scanning calorimetric analysis were applied to samples. Moreover, fiber behavior and delamination of composites were examined by morphological analysis. Tensile test outcomes showed cottonseed oil with 40% oil additive and canola oil with 10% oil addition gave higher strength values to the pure epoxy sample. In the impact test, samples with 20% oil added had an average of 2.7–3.44 times higher absorbed energy. Thermal analysis results indicated 10% and 20% oil addition to epoxy raised the glass transition temperature by an average of 6.65–18.6°C and lowered the decomposition temperatures by 11–24°C. These samples, created by adding vegetable oil to the epoxy without chemical treatment, give the composites considerable elasticity and will be used in areas such as the automotive, construction and aerospace industries.Highlights: Adding plant oil to epoxy creates sustainable and environmentally composite. The usage of plant oils will reduce dependence on petroleum‐based epoxy. The use of plant oil will further pave the way for green composites. Elasticity and energy absorption characteristics of the material are improved. Elongation percent and glass transition temperature of the material improved.
- 26 December 2024
- Published by Wiley in Polymer Composites
- Vol. 46 (8) , 7091-7107
The use of bioresin composites created with five different vegetable oils such as soybean oil, palm oil, rapeseed oil, cottonseed oil, linseed oil in the automotive industry
In this study, novel bioresin was prepared together with epoxy resin with five different plant oils such as soybean oil, palm oil, rapeseed oil, cottonseed oil, and flaxseed oil. The samples were formed by adding jute/flax intraply fiber to the bioresin formed by adding these vegetable oils to the epoxy at 10%, 20%, 30%, and 40%. While producing these composites, vacuum assisted resin transfer molding method was preferred. Tensile, flexural, impact test, thermogravimetric and differential scanning calorimetric analysis were applied to samples. Moreover, fiber behavior and delamination of composites were examined by morphological analysis. Tensile test outcomes showed cottonseed oil with 40% oil additive and canola oil with 10% oil addition gave higher strength values to the pure epoxy sample. In the impact test, samples with 20% oil added had an average of 2.7–3.44 times higher absorbed energy. Thermal analysis results indicated 10% and 20% oil addition to epoxy raised the glass transition temperature by an average of 6.65–18.6°C and lowered the decomposition temperatures by 11–24°C. These samples, created by adding vegetable oil to the epoxy without chemical treatment, give the composites considerable elasticity and will be used in areas such as the automotive, construction and aerospace industries.Highlights: Adding plant oil to epoxy creates sustainable and environmentally composite. The usage of plant oils will reduce dependence on petroleum‐based epoxy. The use of plant oil will further pave the way for green composites. Elasticity and energy absorption characteristics of the material are improved. Elongation percent and glass transition temperature of the material improved.
- 31 July 2024
- Published by Duzce Universitesi Bilim ve Teknoloji Dergisi in Düzce Üniversitesi Bilim ve Teknoloji Dergisi
- Vol. 12 (3) , 1315-1333
A Short Review: The Use and Application of Matrix Resins Formed with Some Plant-Based Oils in Bio-Composite Materials
Increasing environmental problems, waste recycling problems, and non-biodegradable resources have led researchers to different searches for composite materials in recent years. In these studies, interest in bio-composite materials known as green composites has increased significantly due to their potential to replace traditional materials in material production. The creation of biocomposite materials from natural fibers or natural resins instead of synthetic fibers and synthetic resins has made natural resources the focus of researchers. Among these natural resin formations, the use of vegetable-based oils in various applications has started to be seen frequently due to their low cost, biodegradability, and availability. In addition to being recyclable, vegetable-based oils are an important alternative in many sectors, especially in the chemical industry, both environmentally and economically, with a wide variety of chemical conversion possibilities. The desire to explore the versatility of vegetable oil components formed by the complex multi-component mixtures of fatty acids and glycerol ester accelerates the studies in this field even more. In this study, the chemical compositions of vegetable oils hybridized with different resins, the chemical structures of pure vegetable oils, the different varieties among these vegetable oils, and various types of biocomposites produced using vegetable oil-based resins were investigated. In addition, the latest trends in other applications of these bio-composites, especially in automotive, were examined.
- 31 July 2024
- Published by Duzce Universitesi Bilim ve Teknoloji Dergisi in Düzce Üniversitesi Bilim ve Teknoloji Dergisi
- Vol. 12 (3) , 1315-1333
A Short Review: The Use and Application of Matrix Resins Formed with Some Plant-Based Oils in Bio-Composite Materials
Increasing environmental problems, waste recycling problems, and non-biodegradable resources have led researchers to different searches for composite materials in recent years. In these studies, interest in bio-composite materials known as green composites has increased significantly due to their potential to replace traditional materials in material production. The creation of biocomposite materials from natural fibers or natural resins instead of synthetic fibers and synthetic resins has made natural resources the focus of researchers. Among these natural resin formations, the use of vegetable-based oils in various applications has started to be seen frequently due to their low cost, biodegradability, and availability. In addition to being recyclable, vegetable-based oils are an important alternative in many sectors, especially in the chemical industry, both environmentally and economically, with a wide variety of chemical conversion possibilities. The desire to explore the versatility of vegetable oil components formed by the complex multi-component mixtures of fatty acids and glycerol ester accelerates the studies in this field even more. In this study, the chemical compositions of vegetable oils hybridized with different resins, the chemical structures of pure vegetable oils, the different varieties among these vegetable oils, and various types of biocomposites produced using vegetable oil-based resins were investigated. In addition, the latest trends in other applications of these bio-composites, especially in automotive, were examined.
- Open Access
- 11 March 2024
- Published by Osmaniye Korkut Ata Universitesi in Osmaniye Korkut Ata Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 7 (2) , 751-766
Investigation of the Use of Hybrid Composite Materials Formed Using Two Different Resins in Vehicle Bumpers
As efforts to reduce vehicle weight in today's vehicles accelerate, efforts to find new types of materials that can replace traditional materials have accelerated. In this study, carbon fiber was used as a reinforcement element together with glass fiber for lightening in vehicle bumpers. While vinyl ester and polyester were chosen as the matrix material for the piece to be produced, production was made by the hand lay-up method. The produced samples were first subjected to tensile test and their mechanical values were determined. The mechanical test results were introduced to the ANSYS program, and separate analyzes were made for the materials produced on the same bumper design and the results were compared. According to the results of the analysis, there was 2.13 times decrease in total deformations in glass fiber/carbon fiber/Vinyl ester hybrid composites compared to glass fiber/vinyl ester homogeneous composites. In terms of equivalent stresses, 8% reduction was achieved in the carbon fiber /glass fiber/Vinyl ester hybrid composite compared to the carbon/Vinyl ester homogeneous composite. It was concluded that the choice of reinforcement and matrix is important for creating bumper material and improving the mechanical values of the bumper
- 11 March 2024
- Published by Osmaniye Korkut Ata Universitesi in Osmaniye Korkut Ata Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 7 (2) , 751-766
Open AccessInvestigation of the Use of Hybrid Composite Materials Formed Using Two Different Resins in Vehicle Bumpers
As efforts to reduce vehicle weight in today's vehicles accelerate, efforts to find new types of materials that can replace traditional materials have accelerated. In this study, carbon fiber was used as a reinforcement element together with glass fiber for lightening in vehicle bumpers. While vinyl ester and polyester were chosen as the matrix material for the piece to be produced, production was made by the hand lay-up method. The produced samples were first subjected to tensile test and their mechanical values were determined. The mechanical test results were introduced to the ANSYS program, and separate analyzes were made for the materials produced on the same bumper design and the results were compared. According to the results of the analysis, there was 2.13 times decrease in total deformations in glass fiber/carbon fiber/Vinyl ester hybrid composites compared to glass fiber/vinyl ester homogeneous composites. In terms of equivalent stresses, 8% reduction was achieved in the carbon fiber /glass fiber/Vinyl ester hybrid composite compared to the carbon/Vinyl ester homogeneous composite. It was concluded that the choice of reinforcement and matrix is important for creating bumper material and improving the mechanical values of the bumper
- 12 December 2023
- Published by Springer Nature in Iranian Polymer Journal
- Vol. 33 (3) , 289-304
The influence of hybridization and different manufacturing methods on the mechanical properties of the composites reinforced with basalt, jute, and flax fibers
- 12 December 2023
- Published by Springer Nature in Iranian Polymer Journal
- Vol. 33 (3) , 289-304
The influence of hybridization and different manufacturing methods on the mechanical properties of the composites reinforced with basalt, jute, and flax fibers