Yaocong Wang
Yaocong Wang has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Fujian Zhou
State Key Laboratory of Petroleum Resources and Engineering, China University of Petroleum, Beijing 102249, China
2 shared publications - Yunjin Wang
State Key Laboratory of Petroleum Resources and Prospecting, China University of Petroleum (Beijing), Beijing 102249, China
2 shared publications - Chong Liang
Research Institute of Petroleum Exploration & Development, PetroChina, Beijing 100083, China
1 shared publication - Dawei Zhu
PetroChina Research Institute of Petroleum Exploration & Development, Beijing 100083, China
1 shared publication - Fei Yao
Research Institute of Petroleum Exploration and Development, PetroChina, Beijing 100083, China
1 shared publication - Honglan Zou
Research Institute of Petroleum Exploration and Development, PetroChina, Beijing 100083, China
1 shared publication
Latest Publications
- Open Access
Preparation and Performance Study of Microemulsion Acid for Comprehensive Plugging Removal in Carbonate Reservoir
Matrix acidification is one of the most effective stimulations to dissolve scales and remove damage in carbonate reservoirs. However, existing acid systems are difficult to dissolve organic and inorganic scales simultaneously, and complex multi-stage alternative injection often introduces new precipitation and damages the reservoir. Here, based on the retardation ability of emulsified acid and the stable structure of microemulsion, an oil-phase solvent was preferably selected, and the surfactant and cosurfactant were optimized to prepare an acid-in-oil type microemulsion acid capable of dissolving both organic and inorganic scales and high solubilizing for hydrochloric acid. Based on the rotating disc experiment, scale dissolution experiment and acid driving experiment, the acid-rock reaction kinetics, scale dissolution ability and acidizing and plugging removal performance of microemulsion acid in a carbonate reservoir were systematically studied and compared. The results show that Solvesso 150 (aromatic solvent) has the advantages of low toxicity, high flash point and high-scale dissolving ability. At NP−4: OP−10: A (cosurfactant) = 3:3:4, the microemulsion acid system has the strongest ability to solubilize hydrochloric acid and can solve the problem of low H+ concentration. The particle size of microemulsion acid is smaller compared to emulsified acid. At 60 °C, the mass transfer coefficient of microemulsion acid is 3.2 × 10−8 cm2/s, which is one order of magnitude less than that of emulsified acid. Microemulsion acid shows good solubility performance in dissolving organic and inorganic scales, and the comprehensive solubility of mixed scales can reach 98.28%. The stronger scale solubilization ability and lower acid-rock reaction rate enable microemulsion acid to form a thin and straight main wormhole, thus enhancing the acidizing and plugging removal effect. This study can solve the problem of poor hydrochloric acid solubilization ability of microemulsion acid to a certain extent, which provides theoretical and data support for the research and development of microemulsion acid and the efficient plugging removal technology for carbonate reservoirs.
Open AccessPreparation and Performance Study of Microemulsion Acid for Comprehensive Plugging Removal in Carbonate Reservoir
Matrix acidification is one of the most effective stimulations to dissolve scales and remove damage in carbonate reservoirs. However, existing acid systems are difficult to dissolve organic and inorganic scales simultaneously, and complex multi-stage alternative injection often introduces new precipitation and damages the reservoir. Here, based on the retardation ability of emulsified acid and the stable structure of microemulsion, an oil-phase solvent was preferably selected, and the surfactant and cosurfactant were optimized to prepare an acid-in-oil type microemulsion acid capable of dissolving both organic and inorganic scales and high solubilizing for hydrochloric acid. Based on the rotating disc experiment, scale dissolution experiment and acid driving experiment, the acid-rock reaction kinetics, scale dissolution ability and acidizing and plugging removal performance of microemulsion acid in a carbonate reservoir were systematically studied and compared. The results show that Solvesso 150 (aromatic solvent) has the advantages of low toxicity, high flash point and high-scale dissolving ability. At NP−4: OP−10: A (cosurfactant) = 3:3:4, the microemulsion acid system has the strongest ability to solubilize hydrochloric acid and can solve the problem of low H+ concentration. The particle size of microemulsion acid is smaller compared to emulsified acid. At 60 °C, the mass transfer coefficient of microemulsion acid is 3.2 × 10−8 cm2/s, which is one order of magnitude less than that of emulsified acid. Microemulsion acid shows good solubility performance in dissolving organic and inorganic scales, and the comprehensive solubility of mixed scales can reach 98.28%. The stronger scale solubilization ability and lower acid-rock reaction rate enable microemulsion acid to form a thin and straight main wormhole, thus enhancing the acidizing and plugging removal effect. This study can solve the problem of poor hydrochloric acid solubilization ability of microemulsion acid to a certain extent, which provides theoretical and data support for the research and development of microemulsion acid and the efficient plugging removal technology for carbonate reservoirs.
- Open Access
Acid System and Stimulation Efficiency of Multistage Acid Fracturing in Porous Carbonate Reservoirs
With little to no natural fracture development and the high calcite content in porous carbonate reservoirs, for multistage acid fracturing, different fluids are used to form a viscous fingering in the fracture, thus enhancing the degree of nonuniform etching. However, existing studies on multistage acid fracturing mainly focused on the combination of fracturing fluid and acid, which is less specific for porous carbonate rocks. Here, the rheological properties of five fluids, including guar-based fluid, cross-linked guar, gelled acid, cross-linked acid, and diverting acid, were studied at each temperature condition, and the viscosity relationship between each fluid was clarified. Based on the rheological properties, the differences between the seven liquid combinations on the etched morphology of the fracture walls were studied and analyzed. The conductivity of the seven acid-etched fractures under different closure stress was simulated. The experimental results showed that the viscosity relationships between the fluids at different temperatures were cross-linked guar > cross-linked acid > diverting acid (spent acid) > gelled acid > guar-based liquid > diverting acid (fresh acid). Because cross-linked acid has higher viscosity than gelled acid, it can form more obvious viscous fingering with a variety of liquids, which is more suitable for acid fracturing stimulation of porous carbonate reservoirs. In addition, the combination of cross-linked and diverting acids was screened out. The multistage alternate injection of this fluid combination could form tortuous and complex etching channels, and its acid-etching fracture conductivity was significantly higher than that of other fluid combinations at different closure stress. In this study, we optimized the fluid combination of porous carbonates and clarified the effect and mechanism of nonuniform etching to provide guidance for the fluid combination selection of multistage alternate acid fracturing process for porous carbonate reservoirs.
Open AccessAcid System and Stimulation Efficiency of Multistage Acid Fracturing in Porous Carbonate Reservoirs
With little to no natural fracture development and the high calcite content in porous carbonate reservoirs, for multistage acid fracturing, different fluids are used to form a viscous fingering in the fracture, thus enhancing the degree of nonuniform etching. However, existing studies on multistage acid fracturing mainly focused on the combination of fracturing fluid and acid, which is less specific for porous carbonate rocks. Here, the rheological properties of five fluids, including guar-based fluid, cross-linked guar, gelled acid, cross-linked acid, and diverting acid, were studied at each temperature condition, and the viscosity relationship between each fluid was clarified. Based on the rheological properties, the differences between the seven liquid combinations on the etched morphology of the fracture walls were studied and analyzed. The conductivity of the seven acid-etched fractures under different closure stress was simulated. The experimental results showed that the viscosity relationships between the fluids at different temperatures were cross-linked guar > cross-linked acid > diverting acid (spent acid) > gelled acid > guar-based liquid > diverting acid (fresh acid). Because cross-linked acid has higher viscosity than gelled acid, it can form more obvious viscous fingering with a variety of liquids, which is more suitable for acid fracturing stimulation of porous carbonate reservoirs. In addition, the combination of cross-linked and diverting acids was screened out. The multistage alternate injection of this fluid combination could form tortuous and complex etching channels, and its acid-etching fracture conductivity was significantly higher than that of other fluid combinations at different closure stress. In this study, we optimized the fluid combination of porous carbonates and clarified the effect and mechanism of nonuniform etching to provide guidance for the fluid combination selection of multistage alternate acid fracturing process for porous carbonate reservoirs.