Serhiy L. Schwab
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Serhiy L. Schwab has a total of 48 co-authors. Here are the top co-authors by number of shared publications:
- Mykhailo Mykhailovych Voron
Physico-Technological Institute of Metals and Alloys of the National Academy of Sciences of Ukraine, Kyiv, Ukraine
23 shared publications - Anastasiia Yuriivna Semenko
Physico-Technological Institute of Metals and Alloys of the National Academy of Sciences of Ukraine, Kyiv, Ukraine
7 shared publications - Andrii M. Tymoshenko
Physico‐Technological Institute of Metals and Alloys of the National Academy of Sciences of Ukraine Kyiv Ukraine
7 shared publications - Oleksiy Mykolaiovych Smirnov
Physico-Technological Institute of Metals and Alloys of the National Academy of Sciences of Ukraine, Kyiv, Ukraine
7 shared publications - Roman V. Selin
Institut elektrozvaruvanna imeni E O Patona Nacional'na akademia nauk Ukraini
7 shared publications - Yuliia P. Skorobagatko
Physico-technological Institute of Metals and Alloys of the NAS of Ukraine (Kyiv, Ukraine)
7 shared publications
Latest Publications
- Open Access
- 18 June 2026
- Published by Elsevier in SSRN Electronic Journal
MICROSTRUCTURE AND TRIBO-MECHANICAL RESPONSE OF Ti20Nb20Zr ALLOY AFTER GAS NITRIDING UNDER A WIDE TIME-TEMPERATURE RANGE
A Ti–20Nb–20Zr (wt.%) alloy cast by electron beam remelting with an initial coarse-grained β-structure was studied. Isothermal gas nitriding was carried out in a high-purity nitrogen atmosphere (1 atm N2) over a wide time-temperature range (750–850 °C for 5–15 hrs, with a step of 50 °C and 5 hrs, respectively). The phase composition, microstructure, mechanical, and tribological properties were evaluated by XRD, TEM, optical microscopy, micro-indentation, and reciprocating wear tests. It was found that gas nitriding forms a modified compound layer: an upper thin nanostructured chemical layer consisting of mononitrides of the alloy’s elements (TiN, ZrN, and NbN) and a sublayer of micron-sized polyhedral Ti2N grains. Below the compound layer, a diffusion-strengthened Ti(N) zone was formed due to a solid-solution phenomenon, which is represented by a two-phase α+β-structure. With increased temperature-time parameters during nitriding, the surface microhardness and elastic modulus increase, while the process temperature has a significant effect on the level of hardening, whereas the exposure time primarily determines the elastic properties. It was shown that nitriding at 850 °C for 15 hrs provides maximum surface hardening (microhardness 7 GPa, modulus of elasticity 105 GPa) with a diffusion layer depth of up to ~20 μm. In addition, this treatment regime caused the lowest friction complex of the alloy: a stable, low coefficient of friction (0.8 vs 1.3) and almost two orders of magnitude higher wear resistance (525.5±25·10-6 vs 3.5±2·10-6 mm3·N–1·m–1) compared to the untreated one.
- 18 June 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessMICROSTRUCTURE AND TRIBO-MECHANICAL RESPONSE OF Ti20Nb20Zr ALLOY AFTER GAS NITRIDING UNDER A WIDE TIME-TEMPERATURE RANGE
A Ti–20Nb–20Zr (wt.%) alloy cast by electron beam remelting with an initial coarse-grained β-structure was studied. Isothermal gas nitriding was carried out in a high-purity nitrogen atmosphere (1 atm N2) over a wide time-temperature range (750–850 °C for 5–15 hrs, with a step of 50 °C and 5 hrs, respectively). The phase composition, microstructure, mechanical, and tribological properties were evaluated by XRD, TEM, optical microscopy, micro-indentation, and reciprocating wear tests. It was found that gas nitriding forms a modified compound layer: an upper thin nanostructured chemical layer consisting of mononitrides of the alloy’s elements (TiN, ZrN, and NbN) and a sublayer of micron-sized polyhedral Ti2N grains. Below the compound layer, a diffusion-strengthened Ti(N) zone was formed due to a solid-solution phenomenon, which is represented by a two-phase α+β-structure. With increased temperature-time parameters during nitriding, the surface microhardness and elastic modulus increase, while the process temperature has a significant effect on the level of hardening, whereas the exposure time primarily determines the elastic properties. It was shown that nitriding at 850 °C for 15 hrs provides maximum surface hardening (microhardness 7 GPa, modulus of elasticity 105 GPa) with a diffusion layer depth of up to ~20 μm. In addition, this treatment regime caused the lowest friction complex of the alloy: a stable, low coefficient of friction (0.8 vs 1.3) and almost two orders of magnitude higher wear resistance (525.5±25·10-6 vs 3.5±2·10-6 mm3·N–1·m–1) compared to the untreated one.
- 23 March 2026
- Published by Wiley in Steel Research International
Influence of Welding Processes on Microstructure and Hardness of Welded Joints of UHSL Steel Fe‐26Mn‐10Al‐1.2Si‐2.2Cr‐1.8Ni‐0.15V‐1C
Ultrahigh‐Strength Lightweight Steels (UHSL steels) are advanced structural materials designed to combine extremely high strength with reduced density. They typically achieve tensile strengths above 1.5 GPa while maintaining good ductility and toughness. This is often accomplished by alloying with elements such as Mn, Al, and Si, which lower the steel's density and stabilize complex microstructures like austenite and martensite. Owing to their excellent strength‐to‐weight ratio, UHSL steels are promising for aerospace, automotive, and defense applications, where both mechanical performance and weight reduction are critical. This paper presents experiments on welding Fe‐26 Mn‐10Al‐1.2Si‐2.2Cr‐1.8Ni‐0.15V‐1C steel using two methods: MMA and MAG, and investigates the microstructural features of the formation of welded joints with a thickness of 9 mm, as well as their hardness.
- 23 March 2026
- Published by Wiley in Steel Research International
Influence of Welding Processes on Microstructure and Hardness of Welded Joints of UHSL Steel Fe‐26Mn‐10Al‐1.2Si‐2.2Cr‐1.8Ni‐0.15V‐1C
Ultrahigh‐Strength Lightweight Steels (UHSL steels) are advanced structural materials designed to combine extremely high strength with reduced density. They typically achieve tensile strengths above 1.5 GPa while maintaining good ductility and toughness. This is often accomplished by alloying with elements such as Mn, Al, and Si, which lower the steel's density and stabilize complex microstructures like austenite and martensite. Owing to their excellent strength‐to‐weight ratio, UHSL steels are promising for aerospace, automotive, and defense applications, where both mechanical performance and weight reduction are critical. This paper presents experiments on welding Fe‐26 Mn‐10Al‐1.2Si‐2.2Cr‐1.8Ni‐0.15V‐1C steel using two methods: MMA and MAG, and investigates the microstructural features of the formation of welded joints with a thickness of 9 mm, as well as their hardness.
- 17 January 2026
- Published by Springer Nature in Welding in the World
- Vol. 70 (10) , 1-12
Obtaining a medium entropy alloy based on the Ti–Zr–Hf–Nb–Ta system using filler cored wire and WAAM technology
- 17 January 2026
- Published by Springer Nature in Welding in the World
- Vol. 70 (10) , 1-12
Obtaining a medium entropy alloy based on the Ti–Zr–Hf–Nb–Ta system using filler cored wire and WAAM technology
- 6 November 2025
- Published by Springer Nature in Materials Science
- Vol. 61 (3) , 409-418
Structure, modulus of elasticity, and corrosion resistance of Ti–20Nb–20Zr alloy
- 6 November 2025
- Published by Springer Nature in Materials Science
- Vol. 61 (3) , 409-418
Structure, modulus of elasticity, and corrosion resistance of Ti–20Nb–20Zr alloy
- 27 October 2025
- Published by Wiley in Steel Research International
- Vol. 97 (5) , 2421-2428
Nonmetallic Inclusions in Fe–26Mn–10Al–1.2Si–3Cr–3Ni–1.4C–0.1V Induction‐Melted Steel and their Influence on Fracture Under Hot Plastic Deformation
The work represents study of the nonmetallic inclusions formation and their influence on the fracture of induction‐melted Fe–26Mn–10Al–1.2Si–3Cr–3Ni–1.4C–0.1V steel in as‐cast state and under conditions of hot plastic deformation. The microstructure of steel in initial state is investigated, as well as cold and hot fractures. It is shown that the investigated steel has several types of noticeable defects after casting. The first one is represented by small Mn‐rich oxides and eutectic‐like areas, while the other one seems to be Al 2 O 3 films, which leads to microcrack formation. The reason for low deformability is also in a rough columnar grain structure, which points to slow crystallization and impurity movement to the grain boundaries. After 90 min annealing with further rolling from 1050 °C, steel remains prone to hot crack formation. It is mainly caused by initial structure, inclusions, and formation of carbides at the grain boundary, especially in near eutectic areas that contain S and P. XRD investigations show that hot crack surface contains N and C‐rich austenite, iron nitride, as well as Mn and Al oxides with complex Fe–Mn oxides.
- 27 October 2025
- Published by Wiley in Steel Research International
- Vol. 97 (5) , 2421-2428
Nonmetallic Inclusions in Fe–26Mn–10Al–1.2Si–3Cr–3Ni–1.4C–0.1V Induction‐Melted Steel and their Influence on Fracture Under Hot Plastic Deformation
The work represents study of the nonmetallic inclusions formation and their influence on the fracture of induction‐melted Fe–26Mn–10Al–1.2Si–3Cr–3Ni–1.4C–0.1V steel in as‐cast state and under conditions of hot plastic deformation. The microstructure of steel in initial state is investigated, as well as cold and hot fractures. It is shown that the investigated steel has several types of noticeable defects after casting. The first one is represented by small Mn‐rich oxides and eutectic‐like areas, while the other one seems to be Al 2 O 3 films, which leads to microcrack formation. The reason for low deformability is also in a rough columnar grain structure, which points to slow crystallization and impurity movement to the grain boundaries. After 90 min annealing with further rolling from 1050 °C, steel remains prone to hot crack formation. It is mainly caused by initial structure, inclusions, and formation of carbides at the grain boundary, especially in near eutectic areas that contain S and P. XRD investigations show that hot crack surface contains N and C‐rich austenite, iron nitride, as well as Mn and Al oxides with complex Fe–Mn oxides.
- 17 October 2025
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Physicochemical Mechanics of Materials
- Vol. 61 (5) , 30-37
Influence of the granulometric composition of flux cored wire on the deposition stability and structure of 50Kh2N2MFS metal
The influence of the granulometric composition of ferroalloy components in the core of metal-cored wire (MCW) on the stability of the arc surfacing process, MCW melting characteristics, deposition quality, microstructural features, and properties of the multilayer deposited metal was investigated. The MCW core contained an identical mixture of ferroalloy components designed to produce deposited metal of the 50Kh2N2MFS type. The difference between the studied CWs consisted in the granulometric composition of their core: 50…300 μm for the reference MCW and 50…100 μm for the experimental MCW. The feasibility of using ferroalloy compositions with a minimal particle size distribution (50…100 μm) in the MCW core for arc surfacing was demonstrated, as it improved MCW melting characteristics, process stability, and deposition quality, which in turn positively affected the structure and properties of the deposited metal.
- 17 October 2025
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Physicochemical Mechanics of Materials
- Vol. 61 (5) , 30-37
Influence of the granulometric composition of flux cored wire on the deposition stability and structure of 50Kh2N2MFS metal
The influence of the granulometric composition of ferroalloy components in the core of metal-cored wire (MCW) on the stability of the arc surfacing process, MCW melting characteristics, deposition quality, microstructural features, and properties of the multilayer deposited metal was investigated. The MCW core contained an identical mixture of ferroalloy components designed to produce deposited metal of the 50Kh2N2MFS type. The difference between the studied CWs consisted in the granulometric composition of their core: 50…300 μm for the reference MCW and 50…100 μm for the experimental MCW. The feasibility of using ferroalloy compositions with a minimal particle size distribution (50…100 μm) in the MCW core for arc surfacing was demonstrated, as it improved MCW melting characteristics, process stability, and deposition quality, which in turn positively affected the structure and properties of the deposited metal.
- 1 October 2025
- Published by Springer Nature in Materials Science
- Vol. 61 (5) , 599-606
Influence of the granulometric composition of flux-cored wire on the surfacing stability and structure of 50Kh2N2MFS metal
- 1 October 2025
- Published by Springer Nature in Materials Science
- Vol. 61 (5) , 599-606
Influence of the granulometric composition of flux-cored wire on the surfacing stability and structure of 50Kh2N2MFS metal
- Open Access
- 30 September 2025
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Metaloznavstvo ta obrobka metalìv
- Vol. 31 (3) , 3-12
Microstructural changes of high-strength steel Fe-26Mn-10Al-1.2Si-2.2Cr-1.8Ni-0.15V-1C after ballistic damage
The manuscript is devoted to the study of structural changes in the penetration zone of Fe-26Mn-10Al-1.2Si-2.2Cr-1.8Ni-0.15V-1C steel, which was developed for ballistic damage protection. Obtaining thin plates from lightweight high-strength steels based on the Fe-Mn-Al-C system for such use is an extremely promising and unexplored task. The work analyzes the influence of mechanical properties and mechanisms of microstructural changes, according to which armor metallic materials and studied type steels can resist bullet damage most effectively. To provide the research, as-cast steel billet was obtained under conditions of open induction melting, and then it was subsequently subjected to hot plastic deformation and normalization. The resulting plate was ballistic tested and the structure of the near-bullet hollow area was investigated. Studies of mechanical properties revealed extremely high strength of steel, the required level of plasticity and average hardness: UTS=2240 MPa, YS=1784 MPa, δ=6.2%, ψ=16.8%, HRC=42-46. Studies of the bullet hollow cross-section area showed the formation of two zones. The first zone repeated the shaper of the bullet and demonstrated significant local plastic deformation of the steel near the strike surface. In the near-surface region, local recrystallization and a microhardness decrease was observed due to thermal influence. When moving closer to the central zone, surface hardening is observed, which is expressed in a noticeable increase in microhardness. The second zone shows signs of brittle fracture. In its microstructure, adiabatic shear bands and places of stress accumulation that form microcracks are observed. In the zone of l plate failure, the formation of microdefects coalescence areas was detected, the shape of which repeats the load distribution inside the material. The obtained data indicate that the proposed steel is suitable for protection against ballistic damage, but at greater thicknesses. It is able to resist ballistic loads due to the effective absorption of impact energy, which is expressed in the implementation of several mechanisms simultaneously - local hardening, formation of ASB, accumulation of defects and stresses and the sequential formation of microcracks, as well as in their coalescence during the deformation of the material.
- 30 September 2025
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Metaloznavstvo ta obrobka metalìv
- Vol. 31 (3) , 3-12
Open AccessMicrostructural changes of high-strength steel Fe-26Mn-10Al-1.2Si-2.2Cr-1.8Ni-0.15V-1C after ballistic damage
The manuscript is devoted to the study of structural changes in the penetration zone of Fe-26Mn-10Al-1.2Si-2.2Cr-1.8Ni-0.15V-1C steel, which was developed for ballistic damage protection. Obtaining thin plates from lightweight high-strength steels based on the Fe-Mn-Al-C system for such use is an extremely promising and unexplored task. The work analyzes the influence of mechanical properties and mechanisms of microstructural changes, according to which armor metallic materials and studied type steels can resist bullet damage most effectively. To provide the research, as-cast steel billet was obtained under conditions of open induction melting, and then it was subsequently subjected to hot plastic deformation and normalization. The resulting plate was ballistic tested and the structure of the near-bullet hollow area was investigated. Studies of mechanical properties revealed extremely high strength of steel, the required level of plasticity and average hardness: UTS=2240 MPa, YS=1784 MPa, δ=6.2%, ψ=16.8%, HRC=42-46. Studies of the bullet hollow cross-section area showed the formation of two zones. The first zone repeated the shaper of the bullet and demonstrated significant local plastic deformation of the steel near the strike surface. In the near-surface region, local recrystallization and a microhardness decrease was observed due to thermal influence. When moving closer to the central zone, surface hardening is observed, which is expressed in a noticeable increase in microhardness. The second zone shows signs of brittle fracture. In its microstructure, adiabatic shear bands and places of stress accumulation that form microcracks are observed. In the zone of l plate failure, the formation of microdefects coalescence areas was detected, the shape of which repeats the load distribution inside the material. The obtained data indicate that the proposed steel is suitable for protection against ballistic damage, but at greater thicknesses. It is able to resist ballistic loads due to the effective absorption of impact energy, which is expressed in the implementation of several mechanisms simultaneously - local hardening, formation of ASB, accumulation of defects and stresses and the sequential formation of microcracks, as well as in their coalescence during the deformation of the material.
- 15 September 2025
- Published by Springer Nature in Materials Science
- Vol. 61 (2) , 165-173
The influence of the heredity effect on the structure of multilayer metal deposited with flux-cored wires
- 15 September 2025
- Published by Springer Nature in Materials Science
- Vol. 61 (2) , 165-173
The influence of the heredity effect on the structure of multilayer metal deposited with flux-cored wires
- 21 August 2025
- Published by International Association Welding
- Vol. 2025 (3) , 51-58
Causes for Fe–25Mn–10Al–1Si–2Ni–2Cr–1.4C–0.1V steel fracture due to hot plastic deformation after electroslag remelting of a cast electrode with an increased content of non-metallic inclusions
Electrometallurgy Today, 2025, №03. SOVREMENNAYA ELEKTROMETALLURGIYA Quarterly scientific-technical and production journal. ISSN: 2415-8445, Since 1985. Text in Russian, contents and summaries in English. The journal presents the results of theoretical and experimental research carried out at the PWI in the field of electrometallurgy. Special attention is given to electroslag technology (electroslag melting, refining and casting). The journal is divided into the following main sections: electroslag technology; electron beam processes; plasma arc technology; vacuum arc remelting and vacuum induction melting; general problems of special electrometallurgy.
- 21 August 2025
- Published by International Association Welding
- Vol. 2025 (3) , 51-58
Causes for Fe–25Mn–10Al–1Si–2Ni–2Cr–1.4C–0.1V steel fracture due to hot plastic deformation after electroslag remelting of a cast electrode with an increased content of non-metallic inclusions
Electrometallurgy Today, 2025, №03. SOVREMENNAYA ELEKTROMETALLURGIYA Quarterly scientific-technical and production journal. ISSN: 2415-8445, Since 1985. Text in Russian, contents and summaries in English. The journal presents the results of theoretical and experimental research carried out at the PWI in the field of electrometallurgy. Special attention is given to electroslag technology (electroslag melting, refining and casting). The journal is divided into the following main sections: electroslag technology; electron beam processes; plasma arc technology; vacuum arc remelting and vacuum induction melting; general problems of special electrometallurgy.