Feiyu Teng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Feiyu Teng has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Mingshun Jiang
Shandong University
7 shared publications - Lei Zhang
The School of Control Science and Engineering, Shandong University, Jinan 250061, China
6 shared publications - Juntao Wei
School of Control Science and Engineering, Shandong University, Jinan, China
5 shared publications - Hong Zhang
School of Control Science and Engineering, Shandong University, Jinan, China
3 shared publications - Lingyu Sun
College of Control Science and Engineering, China University of Petroleum (East China), Qingdao, China
3 shared publications - Shanshan Lv
School of Electrical Engineering and Automation, Qilu University of Technology (Shandong Academy of Sciences), JiNan, China
3 shared publications
Latest Publications
- 2 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 75 (00189456) , 1-13
Quantitative Identification of Corrosion Degree in Plate-Like Structures Based on Multifeature Fusion and Sensor Path Optimization
Pitting corrosion on the surface of an aluminum alloy plate will reduce its structural strength and affect structural safety. In this paper, a quantitative identification method of corrosion degree based on the combination of multiple damage characteristics and sensor path optimization is proposed. First, finite element (FE) analysis is used to simulate the effect of different degrees of corrosion on Lamb waves. Nine parameters were analyzed for their correlation with corrosion degree, from which three damage indices (DIs) based on the amplitude and energy of the scattered signals were ultimately selected. Correlation functions between three damage indices and corrosion degree were then established for quantitative identification. Additionally, the influence of the number of paths on the results was studied, and the optimal number of paths for identification was determined. And multiple simulation experiments were conducted involving different corrosion locations and degrees, resulting in the mean absolute error (MAE) of less than 46 mm³. Finally, an experimental system was built to conduct corrosion identification experiments, achieving an MAE of less than 50 mm³, closely matching the simulation results. These research findings demonstrate that the correlation functions derived from simulation exhibits good accuracy and stability in the detection of corrosion with regular shapes.
- 2 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 75 (00189456) , 1-13
Quantitative Identification of Corrosion Degree in Plate-Like Structures Based on Multifeature Fusion and Sensor Path Optimization
Pitting corrosion on the surface of an aluminum alloy plate will reduce its structural strength and affect structural safety. In this paper, a quantitative identification method of corrosion degree based on the combination of multiple damage characteristics and sensor path optimization is proposed. First, finite element (FE) analysis is used to simulate the effect of different degrees of corrosion on Lamb waves. Nine parameters were analyzed for their correlation with corrosion degree, from which three damage indices (DIs) based on the amplitude and energy of the scattered signals were ultimately selected. Correlation functions between three damage indices and corrosion degree were then established for quantitative identification. Additionally, the influence of the number of paths on the results was studied, and the optimal number of paths for identification was determined. And multiple simulation experiments were conducted involving different corrosion locations and degrees, resulting in the mean absolute error (MAE) of less than 46 mm³. Finally, an experimental system was built to conduct corrosion identification experiments, achieving an MAE of less than 50 mm³, closely matching the simulation results. These research findings demonstrate that the correlation functions derived from simulation exhibits good accuracy and stability in the detection of corrosion with regular shapes.
- 6 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. PP (00189456) , 1
Recognition of weld damage in T-welded steel based on a modified reconstruction algorithm for probabilistic inspection of damage
Using ultrasonic guided wave(UGW) technology to realize on-line crack damage identification of T-welded steel has been a research hotspot in recent years. However, in practical engineering applications, the localization results of the traditional reconstruction algorithm for probabilistic inspection of damage (RAPID) are affected by the path sparsity. In addition, the modes of the guided wave (GW) signals are complex and seriously aliased, which makes it challenging to apply high-precision damage localization methods based on time-of-flight (TOF), such as the time-reversal method. To this end, this paper proposes a modified RAPID based on imaging path pairs. A T-welded steel experiment system is built, and firstly, the laws of GW signals under different excitation parameters are analyzed. After that, the effects of the welds on various types of path signals are determined. Then, the subregion where the damage is located is determined based on the damage indices (DIs) of the constituent paths and assessment paths. Finally, probabilistic imaging is performed using imaging path pairs. Simulated and real damages are utilized to validate the effectiveness of the proposed method. The results show that the average localization error of the proposed method is 5.8 mm, which is a significant advantage over the traditional RAPID and TOF-based RAPID.
- 6 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. PP (00189456) , 1
Recognition of weld damage in T-welded steel based on a modified reconstruction algorithm for probabilistic inspection of damage
Using ultrasonic guided wave(UGW) technology to realize on-line crack damage identification of T-welded steel has been a research hotspot in recent years. However, in practical engineering applications, the localization results of the traditional reconstruction algorithm for probabilistic inspection of damage (RAPID) are affected by the path sparsity. In addition, the modes of the guided wave (GW) signals are complex and seriously aliased, which makes it challenging to apply high-precision damage localization methods based on time-of-flight (TOF), such as the time-reversal method. To this end, this paper proposes a modified RAPID based on imaging path pairs. A T-welded steel experiment system is built, and firstly, the laws of GW signals under different excitation parameters are analyzed. After that, the effects of the welds on various types of path signals are determined. Then, the subregion where the damage is located is determined based on the damage indices (DIs) of the constituent paths and assessment paths. Finally, probabilistic imaging is performed using imaging path pairs. Simulated and real damages are utilized to validate the effectiveness of the proposed method. The results show that the average localization error of the proposed method is 5.8 mm, which is a significant advantage over the traditional RAPID and TOF-based RAPID.
- 1 April 2025
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 34 (4) , 045002
Dual-signal reconstruction algorithm under empirical mode decomposition in ultrasonic guided waves for temperature compensation
Pipeline structures are widely used in industry, but the increase in service life may lead to damage to the pipeline structure, bringing economic losses. Ultrasonic guided wave has been widely used for accurate damage detection of pipeline structures. However, temperature variations can also lead to changes in guided wave signals. In order to reduce the influence brought by the external environment, this paper proposes a dual-signal reconstruction method based on empirical mode decomposition. By simultaneously performing empirical mode decomposition on the baseline signal and the test signal and quantifying the correlation between their intrinsic mode functions, the similarity between the two signals can be effectively enhanced, thereby mitigating the impact of signal fluctuations caused by environmental variations. The experiments were conducted with 28.25 ∘C as the baseline, and 100 % accuracy of condition monitoring was achieved under a temperature fluctuation of 9.5 ∘C.
- 1 April 2025
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 34 (4) , 045002
Dual-signal reconstruction algorithm under empirical mode decomposition in ultrasonic guided waves for temperature compensation
Pipeline structures are widely used in industry, but the increase in service life may lead to damage to the pipeline structure, bringing economic losses. Ultrasonic guided wave has been widely used for accurate damage detection of pipeline structures. However, temperature variations can also lead to changes in guided wave signals. In order to reduce the influence brought by the external environment, this paper proposes a dual-signal reconstruction method based on empirical mode decomposition. By simultaneously performing empirical mode decomposition on the baseline signal and the test signal and quantifying the correlation between their intrinsic mode functions, the similarity between the two signals can be effectively enhanced, thereby mitigating the impact of signal fluctuations caused by environmental variations. The experiments were conducted with 28.25 ∘C as the baseline, and 100 % accuracy of condition monitoring was achieved under a temperature fluctuation of 9.5 ∘C.
- 30 November 2024
- Published by SAGE Publications in Structural Health Monitoring
- Vol. 25 (2) , 725-741
Design and implementation of a digital smart layer for ultrasonic-guided wave-based structural health monitoring
Ultrasonic-guided wave (UGW) is an important technology for realizing structural health monitoring (SHM), and the piezoelectric transducer (PZT) is a commonly used actuator and sensor. The PZT layer is fabricated using a flexible printed circuit (FPC), and the interface of the PZTs is connected to the host of the monitoring system via cables. The flexible PZT layer (FPL) is easy to install, highly reliable, and widely used in industrial sites. However, as the distance between the host and the FPL gradually increases, the problem of guided wave (GW) signal attenuation caused by cables cannot be ignored. In addition, the use of shielded cables has the problem of heavy quality and high cost, and the use of unshielded cables has the problem of signal interference. Therefore, this paper proposes a digital smart layer (DSL) composed of a flexible signal acquisition system and a PZT array. The DSL acquires excitation and GW signals acquisition and performs PZT diagnostics. It connects to the host via a fixed six-wire cable and uses digital signals for communication. Multiple DSLs can be interconnected to form a network and perform damage detection simultaneously, improving the monitoring area and damage detection efficiency of the system. An experimental system was constructed on an aluminum plate to verify the functionality of the DSL. The results prove that the DSL solves the problems of signal attenuation and interference susceptibility of GW signal in long-distance cable transmission and realizes the diagnosis of PZT faults such as debonding and breakage. This paper provides a highly reliable and practical means of monitoring the condition of equipment structures such as airplanes, trains, and bridges.
- 30 November 2024
- Published by SAGE Publications in Structural Health Monitoring
- Vol. 25 (2) , 725-741
Design and implementation of a digital smart layer for ultrasonic-guided wave-based structural health monitoring
Ultrasonic-guided wave (UGW) is an important technology for realizing structural health monitoring (SHM), and the piezoelectric transducer (PZT) is a commonly used actuator and sensor. The PZT layer is fabricated using a flexible printed circuit (FPC), and the interface of the PZTs is connected to the host of the monitoring system via cables. The flexible PZT layer (FPL) is easy to install, highly reliable, and widely used in industrial sites. However, as the distance between the host and the FPL gradually increases, the problem of guided wave (GW) signal attenuation caused by cables cannot be ignored. In addition, the use of shielded cables has the problem of heavy quality and high cost, and the use of unshielded cables has the problem of signal interference. Therefore, this paper proposes a digital smart layer (DSL) composed of a flexible signal acquisition system and a PZT array. The DSL acquires excitation and GW signals acquisition and performs PZT diagnostics. It connects to the host via a fixed six-wire cable and uses digital signals for communication. Multiple DSLs can be interconnected to form a network and perform damage detection simultaneously, improving the monitoring area and damage detection efficiency of the system. An experimental system was constructed on an aluminum plate to verify the functionality of the DSL. The results prove that the DSL solves the problems of signal attenuation and interference susceptibility of GW signal in long-distance cable transmission and realizes the diagnosis of PZT faults such as debonding and breakage. This paper provides a highly reliable and practical means of monitoring the condition of equipment structures such as airplanes, trains, and bridges.
- 20 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 73 (00189456) , 1-14
Damage Location Method of Pipeline Structure by Ultrasonic Guided Wave Based on Probability Fusion
Pipeline structures are widely used in construction, oil transportation and other industrial fields, but with increasing service life, pipeline structures can develop health problems such as perforations and cracks, which can cause pipeline fractures and bring serious safety accidents and economic losses if they aren’t detected at an early stage. Ultrasonic guided wave detection technology has been widely applied in precise damage detection of pipeline structures. To facilitate the grasp of structural health status, a pipeline structural damage imaging method combined with time-of-flight (ToF) compensation and probabilistic reconstruction is proposed. This method analyzes the response signals collected under different states, uses the correlation of the signals as the damage index, constructs an elliptical probability distribution, and determines the axial position of the damage. Afterwards, using ToF as the characteristic parameter, a circular probability distribution is constructed to determine the circumferential location of the damage, and finally the precise location of the damage is obtained. 45 test points were selected for the experiment. The average positioning error is 7 mm. The experimental results show that the method has certain recognition ability for single or multiple damages, and has higher accuracy and stability compared to traditional probability reconstruction algorithms.
- 20 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 73 (00189456) , 1-14
Damage Location Method of Pipeline Structure by Ultrasonic Guided Wave Based on Probability Fusion
Pipeline structures are widely used in construction, oil transportation and other industrial fields, but with increasing service life, pipeline structures can develop health problems such as perforations and cracks, which can cause pipeline fractures and bring serious safety accidents and economic losses if they aren’t detected at an early stage. Ultrasonic guided wave detection technology has been widely applied in precise damage detection of pipeline structures. To facilitate the grasp of structural health status, a pipeline structural damage imaging method combined with time-of-flight (ToF) compensation and probabilistic reconstruction is proposed. This method analyzes the response signals collected under different states, uses the correlation of the signals as the damage index, constructs an elliptical probability distribution, and determines the axial position of the damage. Afterwards, using ToF as the characteristic parameter, a circular probability distribution is constructed to determine the circumferential location of the damage, and finally the precise location of the damage is obtained. 45 test points were selected for the experiment. The average positioning error is 7 mm. The experimental results show that the method has certain recognition ability for single or multiple damages, and has higher accuracy and stability compared to traditional probability reconstruction algorithms.
- 19 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 71 (00189456) , 1-13
Ultrasonic Guided Wave Damage Localization in Hole-Structural Bearing Crossbeam Based on Improved RAPID Algorithm
The hole-structural bearing crossbeam plays an important role in high-speed trains. In the service process, however, the long-term fatigue load may lead to structural damage such as cracks, resulting in performance degradation and failure. Ultrasonic guided wave (GW) technology is one of the most effective damage localization methods in structural health monitoring (SHM), with a high damage sensitivity and wide monitoring range. To address the damage localization in bearing crossbeams, a modified reconstruction algorithm for probabilistic inspection of damage (RAPID) based on the corrected probability distribution function is proposed. First, the valid sensor paths affected by damage are obtained using damage index (DI) based on correlation analysis. Then, the positional relationships between valid paths and damage are classified based on the time of flight (TOF). Finally, the damage diagnostic image and localization are obtained by fusion imaging using the corresponding probability distribution functions and shape factors, depending on different types of the path. The effectiveness was verified by numerical simulation and experiment. By taking the crossbeam of the high-speed train as the research object, through the static simulation of the crossbeam stress distribution under load, the damaged hot-spots area is obtained, and the sensor network is designed. And then, the SHM experimental system is constructed to perform damage localization experiments. The localization absolute error was less than 8 mm. Experimental results show that the proposed method can effectively locate the damage position in the crossbeam and has better accuracy and reliability than the traditional RAPID algorithm.
- 19 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 71 (00189456) , 1-13
Ultrasonic Guided Wave Damage Localization in Hole-Structural Bearing Crossbeam Based on Improved RAPID Algorithm
The hole-structural bearing crossbeam plays an important role in high-speed trains. In the service process, however, the long-term fatigue load may lead to structural damage such as cracks, resulting in performance degradation and failure. Ultrasonic guided wave (GW) technology is one of the most effective damage localization methods in structural health monitoring (SHM), with a high damage sensitivity and wide monitoring range. To address the damage localization in bearing crossbeams, a modified reconstruction algorithm for probabilistic inspection of damage (RAPID) based on the corrected probability distribution function is proposed. First, the valid sensor paths affected by damage are obtained using damage index (DI) based on correlation analysis. Then, the positional relationships between valid paths and damage are classified based on the time of flight (TOF). Finally, the damage diagnostic image and localization are obtained by fusion imaging using the corresponding probability distribution functions and shape factors, depending on different types of the path. The effectiveness was verified by numerical simulation and experiment. By taking the crossbeam of the high-speed train as the research object, through the static simulation of the crossbeam stress distribution under load, the damaged hot-spots area is obtained, and the sensor network is designed. And then, the SHM experimental system is constructed to perform damage localization experiments. The localization absolute error was less than 8 mm. Experimental results show that the proposed method can effectively locate the damage position in the crossbeam and has better accuracy and reliability than the traditional RAPID algorithm.