Rui Hao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Rui Hao has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Weiwei Lin
Department of Civil Engineering, Aalto University, Espoo 02150, Finland
5 shared publications - Di Su
The University of Tokyo
2 shared publications - Lingfang Li
Department of Civil and Environmental Engineering, The Hong Kong Polytechnic University, Kowloon, Hong Kong, China
2 shared publications Weiwei Lin
2 shared publications- Youqi Zhang
Aalto University
2 shared publications - Zhenkun Li
Department of Civil Engineering, Aalto University, 02150 Espoo, Finland
2 shared publications
Latest Publications
- Open Access
- 24 August 2025
- Published by Elsevier in Theoretical and Applied Fracture Mechanics
- Vol. 140
Fatigue crack propagation behaviors of two weathering steels and the compatible welding material
- 24 August 2025
- Published by Elsevier in Theoretical and Applied Fracture Mechanics
- Vol. 140
Open AccessFatigue crack propagation behaviors of two weathering steels and the compatible welding material
- Open Access
- 12 July 2024
- Published by Taylor & Francis
- p. 2767-2774
Robustness evaluation of a twin I-girder bridge
With the increasing popularity of twin I-girder bridges, lack of robustness of this bridge type has always been a major concern. Though the AASHTO (2012) specification considers all twin I-girder bridges as non-redundant and fracture critical structures, the robustness of these structures can be improved through design criteria updates and the addition of auxiliary members. This study aims to evaluate the robustness of simply supported twin I-girder bridges. Experimental testing was conducted on two scaled bridge specimens (intact and damaged) under asymmetric loading conditions, and the structural responses were analyzed. Obtained test data were used to validate the developed finite element model and non-linear analyses were performed for further investigation. In this study, the robustness of twin I-girder bridge is studied with different vertical positions of crossbeam, considering different damage locations. The results obtained indicate an enhanced system robustness when the crossbeams are positioned at the lower end of the girder.
- 12 July 2024
- Published by Taylor & Francis
- p. 2767-2774
Open AccessRobustness evaluation of a twin I-girder bridge
With the increasing popularity of twin I-girder bridges, lack of robustness of this bridge type has always been a major concern. Though the AASHTO (2012) specification considers all twin I-girder bridges as non-redundant and fracture critical structures, the robustness of these structures can be improved through design criteria updates and the addition of auxiliary members. This study aims to evaluate the robustness of simply supported twin I-girder bridges. Experimental testing was conducted on two scaled bridge specimens (intact and damaged) under asymmetric loading conditions, and the structural responses were analyzed. Obtained test data were used to validate the developed finite element model and non-linear analyses were performed for further investigation. In this study, the robustness of twin I-girder bridge is studied with different vertical positions of crossbeam, considering different damage locations. The results obtained indicate an enhanced system robustness when the crossbeams are positioned at the lower end of the girder.
- Open Access
- 8 November 2023
- Published by Elsevier in Structures
- Vol. 58
Evolution of surface roughness of notched steel details under fatigue loading
- 8 November 2023
- Published by Elsevier in Structures
- Vol. 58
Open AccessEvolution of surface roughness of notched steel details under fatigue loading
- Open Access
- 26 July 2023
- Published by Elsevier in Mechanical Systems and Signal Processing
- Vol. 200
High-fidelity time-series data synthesis based on finite element simulation and data space mapping
- 26 July 2023
- Published by Elsevier in Mechanical Systems and Signal Processing
- Vol. 200
Open AccessHigh-fidelity time-series data synthesis based on finite element simulation and data space mapping
- Open Access
Fatigue Life Prediction of Notched Details Using SWT Model and LEFM-Based Approach
The fatigue crack initiation life of unwelded steel components accounts for the majority of the total fatigue life, and the accurate prediction of it is of vital importance. In this study, a numerical model utilizing the extended finite element method (XFEM) and Smith–Watson–Topper (SWT) model is established to predict the fatigue crack initiation life of notched details extensively used in orthotropic steel deck bridges. Using the user subroutine UDMGINI in Abaqus, a new algorithm was proposed to calculate the damage parameter of SWT under high-cycle fatigue loads. The virtual crack-closure technique (VCCT) was introduced to monitor crack propagation. Nineteen tests were performed, and the results were used to validate the proposed algorithm and XFEM model. The simulation results show that the proposed XFEM model with UDMGINI and VCCT can reasonably predict the fatigue lives of the notched specimens within the regime of high-cycle fatigue with a load ratio of 0.1. The error for the prediction of fatigue initiation life ranges from −27.5% to 41.1%, and the prediction of total fatigue life has a good agreement with the experimental results with a scatter factor of around 2.
Open AccessFatigue Life Prediction of Notched Details Using SWT Model and LEFM-Based Approach
The fatigue crack initiation life of unwelded steel components accounts for the majority of the total fatigue life, and the accurate prediction of it is of vital importance. In this study, a numerical model utilizing the extended finite element method (XFEM) and Smith–Watson–Topper (SWT) model is established to predict the fatigue crack initiation life of notched details extensively used in orthotropic steel deck bridges. Using the user subroutine UDMGINI in Abaqus, a new algorithm was proposed to calculate the damage parameter of SWT under high-cycle fatigue loads. The virtual crack-closure technique (VCCT) was introduced to monitor crack propagation. Nineteen tests were performed, and the results were used to validate the proposed algorithm and XFEM model. The simulation results show that the proposed XFEM model with UDMGINI and VCCT can reasonably predict the fatigue lives of the notched specimens within the regime of high-cycle fatigue with a load ratio of 0.1. The error for the prediction of fatigue initiation life ranges from −27.5% to 41.1%, and the prediction of total fatigue life has a good agreement with the experimental results with a scatter factor of around 2.
- Open Access
Fatigue Tests and Analysis on Welded Joints of Weathering Steel
To investigate the fatigue performance of vertical web stiffener to deck plate welded joints in weathering steel box girders, six specimens of the weathering steel (WS) Q345qNH, four specimens of WS Q420qNH, and four specimens of the plain carbon steel (CS) Q345q for comparison were tested by a vibratory fatigue testing machine, considering different steel grades, yield strengths, stiffener plate thicknesses, and weld types. The fatigue strength was evaluated based on S-N curves and the crack propagation was analyzed by linear elastic fracture mechanics (LEFM). The results show that the fatigue crack of the welded joints was initiated from the end weld toe of the deck plate and subsequently propagated both along the thickness of the deck plate and in the direction perpendicular to the stiffener plate. The fatigue crack initiation and propagation life of WS Q345qNH specimens were longer than those of CS Q345q specimens. The fatigue crack propagation life of WS Q345qNH specimens was longer than that of WS Q420qNH specimens, while the initiation life bore little relationship to the yield strength. Increasing the stiffener plate thickness effectively delayed crack initiation and slowed down its propagation. Compared with fillet welds, full penetration welds extended the fatigue crack propagation life, while no significant improvement was implied for the initiation life. The WS and CS specimens could be classified as having the same fatigue strengths by nominal stress, hot spot stress, and effective notch stress approaches, which were FAT 50, FAT 100, and FAT 225, respectively. Meanwhile, their material constants for LEFM were relatively close to each other.
Open AccessFatigue Tests and Analysis on Welded Joints of Weathering Steel
To investigate the fatigue performance of vertical web stiffener to deck plate welded joints in weathering steel box girders, six specimens of the weathering steel (WS) Q345qNH, four specimens of WS Q420qNH, and four specimens of the plain carbon steel (CS) Q345q for comparison were tested by a vibratory fatigue testing machine, considering different steel grades, yield strengths, stiffener plate thicknesses, and weld types. The fatigue strength was evaluated based on S-N curves and the crack propagation was analyzed by linear elastic fracture mechanics (LEFM). The results show that the fatigue crack of the welded joints was initiated from the end weld toe of the deck plate and subsequently propagated both along the thickness of the deck plate and in the direction perpendicular to the stiffener plate. The fatigue crack initiation and propagation life of WS Q345qNH specimens were longer than those of CS Q345q specimens. The fatigue crack propagation life of WS Q345qNH specimens was longer than that of WS Q420qNH specimens, while the initiation life bore little relationship to the yield strength. Increasing the stiffener plate thickness effectively delayed crack initiation and slowed down its propagation. Compared with fillet welds, full penetration welds extended the fatigue crack propagation life, while no significant improvement was implied for the initiation life. The WS and CS specimens could be classified as having the same fatigue strengths by nominal stress, hot spot stress, and effective notch stress approaches, which were FAT 50, FAT 100, and FAT 225, respectively. Meanwhile, their material constants for LEFM were relatively close to each other.
- Open Access
- 7 July 2022
- Published by Elsevier in SSRN Electronic Journal
High-Fidelity Time-Series Data Synthesis based on Finite Element Simulation and Data Space Projection
Dynamic responses of structures simulated by finite element (FE) analysis can provide rich information for many downstream tasks, e.g., analysis of structural behaviors, design optimization, data-driven identification tasks, etc. The fidelity of simulated time-series data has a crucial effect on the results of those downstream tasks. Insufficient fidelity of simulation data can cause a typical problem: methods work perfectly on simulation data but are not effective on the actual structures. Meanwhile, owing to the successful adoption of Deep Learning (DL) in the engineering field, the demand for high-fidelity simulation data has greatly increased. FE model updating can partially address this problem. However, the time-series data generated by an updated FE model may still not satisfy the quality requirements of the downstream tasks. The simulated time-series data with higher fidelity are needed to further benefit the downstream tasks. Therefore, we proposed a method to synthesize realistic time-series data using finite element simulation and space projection. Two models, including a Dense Neural Network (DNN) and a Dilated Causal Convolutional Neural Network (DCCNN), were designed for realizing the space projection. Vibration experiments were conducted on an I-shaped steel beam to validate the proposed method. In addition to a case with sufficient training data, a few-short learning case is also investigated. The quality of the synthetic data is quantitively analyzed. Furthermore, the effects of sensor location and impact location on the quality of synthetic data are also discussed. Overall, the high quality of the synthetic time-series data generated by the proposed method is fully demonstrated.
- 7 July 2022
- Published by Elsevier in SSRN Electronic Journal
Open AccessHigh-Fidelity Time-Series Data Synthesis based on Finite Element Simulation and Data Space Projection
Dynamic responses of structures simulated by finite element (FE) analysis can provide rich information for many downstream tasks, e.g., analysis of structural behaviors, design optimization, data-driven identification tasks, etc. The fidelity of simulated time-series data has a crucial effect on the results of those downstream tasks. Insufficient fidelity of simulation data can cause a typical problem: methods work perfectly on simulation data but are not effective on the actual structures. Meanwhile, owing to the successful adoption of Deep Learning (DL) in the engineering field, the demand for high-fidelity simulation data has greatly increased. FE model updating can partially address this problem. However, the time-series data generated by an updated FE model may still not satisfy the quality requirements of the downstream tasks. The simulated time-series data with higher fidelity are needed to further benefit the downstream tasks. Therefore, we proposed a method to synthesize realistic time-series data using finite element simulation and space projection. Two models, including a Dense Neural Network (DNN) and a Dilated Causal Convolutional Neural Network (DCCNN), were designed for realizing the space projection. Vibration experiments were conducted on an I-shaped steel beam to validate the proposed method. In addition to a case with sufficient training data, a few-short learning case is also investigated. The quality of the synthetic data is quantitively analyzed. Furthermore, the effects of sensor location and impact location on the quality of synthetic data are also discussed. Overall, the high quality of the synthetic time-series data generated by the proposed method is fully demonstrated.
- Open Access
- 13 May 2022
- Published by Elsevier in Construction and Building Materials
- Vol. 340
Short-term and long-term behavior of RC beams strengthened by galvanized steel mesh laminate
- 13 May 2022
- Published by Elsevier in Construction and Building Materials
- Vol. 340
Open AccessShort-term and long-term behavior of RC beams strengthened by galvanized steel mesh laminate