Chukwuka Onyenwoke
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Chukwuka Onyenwoke has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Duncan Cree
Department of Mechanical Engineering, McMaster University, 1280 Main Street West, Hamilton, ON L8S 4L8, Canada
4 shared publications - Edmund Mupondwa
Department of Chemical and Biological Engineering, University of Saskatchewan, 57 Campus Drive, Saskatoon, SK S7N 5A9, Canada
4 shared publications - Lope G. Tabil
Department of Chemical and Biological Engineering, University of Saskatchewan, 57 Campus Drive, Saskatoon, SK, S7N 5A9, Canada
4 shared publications - Timothy J. Dumonceaux
Agriculture and Agri-Food Canada, Saskatoon Research and Development Centre , Saskatoon, SK , S7N 0X2
3 shared publications - Phani Adapa
National Hydrology Research Centre, Global Institute for Water Security (GIWS), University of Saskatchewan, 11 Innovation Boulevard, Saskatoon, SK S7N 3H5, Canada
2 shared publications - Xue Li
Department of Chemical and Biological Engineering, University of Saskatchewan, 57 Campus Drive, Saskatoon, SK, S7N 5A9, Canada; Bioproducts and Bioprocesses, Science and Technology Branch, Agriculture and Agri-Food Canada, Government of Canada, Saskatoon Research and Development Center, 107 Science Place, Saskatoon, SK, S7N 0X2, Canada
2 shared publications
Latest Publications
- Open Access
Technoeconomic Analysis of Torrefaction and Steam Explosion Pretreatment Prior to Pelletization of Selected Biomass
Lignocellulosic biomass has demonstrated great potential as feedstock for pellet production, notwithstanding the fact that the industrial production of pellets is faced with some economic challenges. This study presents a technoeconomic analysis of six scenarios to develop a process model for pellet production from sawdust and oat straw that employs torrefaction and steam explosion pretreatment prior to pelletization. SuperPro Designer was used to carry out this evaluation. The pellet plants were designed to have a capacity of 9.09 t/h of sawdust and oat straw each. The pellet yield ranged from 59 kt to 72 kt/year. The scenarios analyzed included variations of steam explosion and torrefaction. In some scenarios, materials were lost in the form of liquid and gas due to the pretreatment process. The breakdown of equipment purchase cost showed that the torrefaction reactor is the most expensive unit with approximately 51% of the purchase cost. Facility-dependent and feedstock costs were the major significant contributors to the pellet production cost. The minimum selling prices of the pellets obtained from Scenarios 1–6 were $113.4/t, $118.7/t, $283.4/t, $298.7/t, $200.5/t, and $208.4/t, respectively. The profitability of pellet production as determined by the net present value (NPV), internal rate of return (IRR), and payback period was found to be sensitive to variations in feedstock cost.
Open AccessTechnoeconomic Analysis of Torrefaction and Steam Explosion Pretreatment Prior to Pelletization of Selected Biomass
Lignocellulosic biomass has demonstrated great potential as feedstock for pellet production, notwithstanding the fact that the industrial production of pellets is faced with some economic challenges. This study presents a technoeconomic analysis of six scenarios to develop a process model for pellet production from sawdust and oat straw that employs torrefaction and steam explosion pretreatment prior to pelletization. SuperPro Designer was used to carry out this evaluation. The pellet plants were designed to have a capacity of 9.09 t/h of sawdust and oat straw each. The pellet yield ranged from 59 kt to 72 kt/year. The scenarios analyzed included variations of steam explosion and torrefaction. In some scenarios, materials were lost in the form of liquid and gas due to the pretreatment process. The breakdown of equipment purchase cost showed that the torrefaction reactor is the most expensive unit with approximately 51% of the purchase cost. Facility-dependent and feedstock costs were the major significant contributors to the pellet production cost. The minimum selling prices of the pellets obtained from Scenarios 1–6 were $113.4/t, $118.7/t, $283.4/t, $298.7/t, $200.5/t, and $208.4/t, respectively. The profitability of pellet production as determined by the net present value (NPV), internal rate of return (IRR), and payback period was found to be sensitive to variations in feedstock cost.
- Open Access
- 13 November 2023
- Published by MDPI AG in Preprints.org
Technoeconomic Analysis of Torrefaction and Steam Explosion Pretreatment Prior to Pelletization of Selected Biomass
Lignocellulosic biomass has demonstrated great potential as feedstock for pellet production, notwithstanding the fact that the industrial production of pellets is faced with some economic challenges. This study presents a technoeconomic analysis of six case scenarios to develop a process model for pellet production from sawdust and oat straw that employs torrefaction and steam explosion pretreatment prior to pelletization. SuperPro Designer was used to carry out this evaluation. The pellet plants were designed to have a capacity of 9.09 t/h of sawdust and oat straw each. The pellet yield ranged from 59 kt– 72 kt/year. Scenarios analyzed included variations of steam explosion and torrefaction. In some scenarios materials were lost in the form of liquid and gas due to the pretreatment process. The breakdown of equipment purchase cost showed that the torrefaction reactor is the most expensive unit with about 51% of the purchase cost. Facility-dependent and feedstock costs were the major significant contributors to the pellet production cost. The profitability of pellet production as determined by the net present value (NPV), internal rate of return (IRR), and payback period and was found to be sensitive to variations in feedstock cost.
- 13 November 2023
- Published by MDPI AG in Preprints.org
Open AccessTechnoeconomic Analysis of Torrefaction and Steam Explosion Pretreatment Prior to Pelletization of Selected Biomass
Lignocellulosic biomass has demonstrated great potential as feedstock for pellet production, notwithstanding the fact that the industrial production of pellets is faced with some economic challenges. This study presents a technoeconomic analysis of six case scenarios to develop a process model for pellet production from sawdust and oat straw that employs torrefaction and steam explosion pretreatment prior to pelletization. SuperPro Designer was used to carry out this evaluation. The pellet plants were designed to have a capacity of 9.09 t/h of sawdust and oat straw each. The pellet yield ranged from 59 kt– 72 kt/year. Scenarios analyzed included variations of steam explosion and torrefaction. In some scenarios materials were lost in the form of liquid and gas due to the pretreatment process. The breakdown of equipment purchase cost showed that the torrefaction reactor is the most expensive unit with about 51% of the purchase cost. Facility-dependent and feedstock costs were the major significant contributors to the pellet production cost. The profitability of pellet production as determined by the net present value (NPV), internal rate of return (IRR), and payback period and was found to be sensitive to variations in feedstock cost.
- Open Access
Effect of Torrefaction on the Physiochemical Properties of White Spruce Sawdust for Biofuel Production
Torrefaction pretreatment is a mild form of pyrolysis that has the potential to produce a high-quality raw material for making biofuel that serves as a replacement for coal in the bioenergy industry. Microwave-assisted torrefaction was conducted on white spruce sawdust (WSS) at temperatures of 200 °C, 250 °C, and 300 °C and retention times of 5 min, 7 min, and 9 min in an inert environment. The torrefaction process produces a solid carbon, commonly known as biochar, and condensable (torrefaction liquid (TL)) and non-condensable gases. In this study, torrefaction characteristics were investigated to observe its effects on the thermal and physiochemical properties of the pellets produced. During the torrefaction process, a significant mass loss associated with the decomposition of hemicellulose was observed. The hemicellulose content drastically reduced to approximately 1.8% and the cellulose content was reduced by approximately 10%, while the lignin gained approximately 35% as the severity increased. This led to an improvement in the higher heating value (HHV), hydrophobicity, bulk, particle density, pellet dimensional stability, and pellet density. However, the pellet tensile strength decreased as the torrefaction severity increased. Pellet tensile strength is a critical indicator of biomass pellets that expresses the force required to crush or damage a pellet. Therefore, to enhance the tensile strength of the pellets, the introduction of a binder was necessary. Torrefaction liquid and sawdust were used as additives at different proportions during pelletization. The addition of binders (torrefaction liquid and sawdust) to the pellet formulation increased the tensile strength of the torrefied WSS by approximately 50%. The OH groups in the biomass break down to a limited degree due to dehydration. This hinders the formation of H bonds, thereby increasing the chances that the pretreated biomass will become hydrophobic. The SEM graphs showed that the torrefied WSS pellets demonstrated more firmly glued surfaces with fewer pores spaces when set side by side with the raw pellets. The thermogravimetric analysis conducted showed that the torrefaction of WSS slightly reduced its thermal stability.
Open AccessEffect of Torrefaction on the Physiochemical Properties of White Spruce Sawdust for Biofuel Production
Torrefaction pretreatment is a mild form of pyrolysis that has the potential to produce a high-quality raw material for making biofuel that serves as a replacement for coal in the bioenergy industry. Microwave-assisted torrefaction was conducted on white spruce sawdust (WSS) at temperatures of 200 °C, 250 °C, and 300 °C and retention times of 5 min, 7 min, and 9 min in an inert environment. The torrefaction process produces a solid carbon, commonly known as biochar, and condensable (torrefaction liquid (TL)) and non-condensable gases. In this study, torrefaction characteristics were investigated to observe its effects on the thermal and physiochemical properties of the pellets produced. During the torrefaction process, a significant mass loss associated with the decomposition of hemicellulose was observed. The hemicellulose content drastically reduced to approximately 1.8% and the cellulose content was reduced by approximately 10%, while the lignin gained approximately 35% as the severity increased. This led to an improvement in the higher heating value (HHV), hydrophobicity, bulk, particle density, pellet dimensional stability, and pellet density. However, the pellet tensile strength decreased as the torrefaction severity increased. Pellet tensile strength is a critical indicator of biomass pellets that expresses the force required to crush or damage a pellet. Therefore, to enhance the tensile strength of the pellets, the introduction of a binder was necessary. Torrefaction liquid and sawdust were used as additives at different proportions during pelletization. The addition of binders (torrefaction liquid and sawdust) to the pellet formulation increased the tensile strength of the torrefied WSS by approximately 50%. The OH groups in the biomass break down to a limited degree due to dehydration. This hinders the formation of H bonds, thereby increasing the chances that the pretreated biomass will become hydrophobic. The SEM graphs showed that the torrefied WSS pellets demonstrated more firmly glued surfaces with fewer pores spaces when set side by side with the raw pellets. The thermogravimetric analysis conducted showed that the torrefaction of WSS slightly reduced its thermal stability.
- Open Access
Investigation of Steam Explosion Pretreatment of Sawdust and Oat Straw to Improve Their Quality as Biofuel Pellets
Steam explosion pretreatment of sawdust and oat straw under mild, medium, and severe conditions was conducted to improve the quality of pellets generated from these feedstocks. This work examined the effects of temperature, time, and moisture content on the mechanical properties of biomass pellets. From the ANOVA conducted, the p-values of the regression models for all the response variables (dimensional stability, tensile strength, and pellet density) studied were significant (p < 0.05), except for the pellet density of steam-pretreated oat straw pellets. The interaction of these three factors did not significantly affect the response variables of oat straw pellets. In addition, the higher heating value (HHV) of treated biomass increased up to a maximum of about 9.5% and 7% as compared with the non-treated sawdust and oat straw, respectively. In addition, an increment of about 3.6-fold and 3.1-fold in pellet tensile strength of steam-pretreated sawdust and oat straw was observed, respectively. Microstructural examination of the pellets from steam-pretreated biomass revealed that the material contained particles that were more closely bonded and featured a cemented surface with fewer pores when compared to particles from untreated oat straw and sawdust.
Open AccessInvestigation of Steam Explosion Pretreatment of Sawdust and Oat Straw to Improve Their Quality as Biofuel Pellets
Steam explosion pretreatment of sawdust and oat straw under mild, medium, and severe conditions was conducted to improve the quality of pellets generated from these feedstocks. This work examined the effects of temperature, time, and moisture content on the mechanical properties of biomass pellets. From the ANOVA conducted, the p-values of the regression models for all the response variables (dimensional stability, tensile strength, and pellet density) studied were significant (p < 0.05), except for the pellet density of steam-pretreated oat straw pellets. The interaction of these three factors did not significantly affect the response variables of oat straw pellets. In addition, the higher heating value (HHV) of treated biomass increased up to a maximum of about 9.5% and 7% as compared with the non-treated sawdust and oat straw, respectively. In addition, an increment of about 3.6-fold and 3.1-fold in pellet tensile strength of steam-pretreated sawdust and oat straw was observed, respectively. Microstructural examination of the pellets from steam-pretreated biomass revealed that the material contained particles that were more closely bonded and featured a cemented surface with fewer pores when compared to particles from untreated oat straw and sawdust.