Edmund Mupondwa
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Edmund Mupondwa has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Lope G. Tabil
Department of Chemical and Biological Engineering, University of Saskatchewan, 57 Campus Drive, Saskatoon, SK, S7N 5A9, Canada
19 shared publications - Duncan Cree
Department of Mechanical Engineering, McMaster University, 1280 Main Street West, Hamilton, ON L8S 4L8, Canada
11 shared publications Xue Li
Bioproducts and Bioprocesses, Science and Technology Branch, Agriculture and Agri-Food Canada, Government of Canada, Saskatoon Research and Development Centre, 107 Science Place, Saskatoon, SK, Canada S7N0X2
8 shared publications- Timothy J. Dumonceaux
Agriculture and Agri-Food Canada, Saskatoon Research and Development Centre , Saskatoon, SK , S7N 0X2
7 shared publications - Chukwuka Onyenwoke
Department of Chemical and Biological Engineering, University of Saskatchewan, 57 Campus Drive, Saskatoon, SK S7N 5A9, Canada
4 shared publications - Obiora Samuel Agu
Department of Chemical and Biological Engineering, University of Saskatchewan, 57 Campus Drive, Saskatoon, SK S7N 5A9, Canada
4 shared publications
Latest Publications
- Open Access
Grindability of Torrefied Camelina Straw and Microparticle Evaluation by Confocal Laser Scanning Microscopy for Use as Biofuel
This study examined the combined effect of torrefaction and microwave absorbers on improving biomass thermochemical characteristics and grindability for heat, power, and value-added products. Camelina straw in two grinds, ground (6.4 mm screen size) and chopped with biochar addition (0%, 10% and 20%), was torrefied in a bench-scale microwave reactor at torrefaction temperatures of 250 °C and 300 °C with residence times of 10, 15 and 20 min under inert conditions and nitrogen-activated. After torrefaction, the geometric mean particle and size distribution, moisture content, ash content, bulk and particle densities were determined, and the grinding performance values of torrefied ground and chopped with and without biochar were determined and compared with the raw camelina straw. The results showed that the geometric diameter decreased after torrefaction in both grinds. The specific energy required for grinding torrefied biomass decreased significantly with biochar addition, longer residence times, and increased torrefaction temperatures. Torrefied ground camelina straw with biochar after grinding had the lowest grinding energy of 34.30 kJ at 300 °C/20 min. The surface morphology by confocal laser scanning microscopy of torrefied camelina straw particles indicated that biochar addition (>10%) and a torrefaction temperature at 250 °C can create profound surface distortion, and beyond 300 °C, colossal surface damage and carbonized weight fractions were produced.
Open AccessGrindability of Torrefied Camelina Straw and Microparticle Evaluation by Confocal Laser Scanning Microscopy for Use as Biofuel
This study examined the combined effect of torrefaction and microwave absorbers on improving biomass thermochemical characteristics and grindability for heat, power, and value-added products. Camelina straw in two grinds, ground (6.4 mm screen size) and chopped with biochar addition (0%, 10% and 20%), was torrefied in a bench-scale microwave reactor at torrefaction temperatures of 250 °C and 300 °C with residence times of 10, 15 and 20 min under inert conditions and nitrogen-activated. After torrefaction, the geometric mean particle and size distribution, moisture content, ash content, bulk and particle densities were determined, and the grinding performance values of torrefied ground and chopped with and without biochar were determined and compared with the raw camelina straw. The results showed that the geometric diameter decreased after torrefaction in both grinds. The specific energy required for grinding torrefied biomass decreased significantly with biochar addition, longer residence times, and increased torrefaction temperatures. Torrefied ground camelina straw with biochar after grinding had the lowest grinding energy of 34.30 kJ at 300 °C/20 min. The surface morphology by confocal laser scanning microscopy of torrefied camelina straw particles indicated that biochar addition (>10%) and a torrefaction temperature at 250 °C can create profound surface distortion, and beyond 300 °C, colossal surface damage and carbonized weight fractions were produced.
- Open Access
Technoeconomic Analysis of Torrefaction and Steam Explosion Pretreatment Prior to Pelletization of Selected Biomass
Lignocellulosic biomass has demonstrated great potential as feedstock for pellet production, notwithstanding the fact that the industrial production of pellets is faced with some economic challenges. This study presents a technoeconomic analysis of six scenarios to develop a process model for pellet production from sawdust and oat straw that employs torrefaction and steam explosion pretreatment prior to pelletization. SuperPro Designer was used to carry out this evaluation. The pellet plants were designed to have a capacity of 9.09 t/h of sawdust and oat straw each. The pellet yield ranged from 59 kt to 72 kt/year. The scenarios analyzed included variations of steam explosion and torrefaction. In some scenarios, materials were lost in the form of liquid and gas due to the pretreatment process. The breakdown of equipment purchase cost showed that the torrefaction reactor is the most expensive unit with approximately 51% of the purchase cost. Facility-dependent and feedstock costs were the major significant contributors to the pellet production cost. The minimum selling prices of the pellets obtained from Scenarios 1–6 were $113.4/t, $118.7/t, $283.4/t, $298.7/t, $200.5/t, and $208.4/t, respectively. The profitability of pellet production as determined by the net present value (NPV), internal rate of return (IRR), and payback period was found to be sensitive to variations in feedstock cost.
Open AccessTechnoeconomic Analysis of Torrefaction and Steam Explosion Pretreatment Prior to Pelletization of Selected Biomass
Lignocellulosic biomass has demonstrated great potential as feedstock for pellet production, notwithstanding the fact that the industrial production of pellets is faced with some economic challenges. This study presents a technoeconomic analysis of six scenarios to develop a process model for pellet production from sawdust and oat straw that employs torrefaction and steam explosion pretreatment prior to pelletization. SuperPro Designer was used to carry out this evaluation. The pellet plants were designed to have a capacity of 9.09 t/h of sawdust and oat straw each. The pellet yield ranged from 59 kt to 72 kt/year. The scenarios analyzed included variations of steam explosion and torrefaction. In some scenarios, materials were lost in the form of liquid and gas due to the pretreatment process. The breakdown of equipment purchase cost showed that the torrefaction reactor is the most expensive unit with approximately 51% of the purchase cost. Facility-dependent and feedstock costs were the major significant contributors to the pellet production cost. The minimum selling prices of the pellets obtained from Scenarios 1–6 were $113.4/t, $118.7/t, $283.4/t, $298.7/t, $200.5/t, and $208.4/t, respectively. The profitability of pellet production as determined by the net present value (NPV), internal rate of return (IRR), and payback period was found to be sensitive to variations in feedstock cost.
- Open Access
- 13 November 2023
- Published by MDPI AG in Preprints.org
Technoeconomic Analysis of Torrefaction and Steam Explosion Pretreatment Prior to Pelletization of Selected Biomass
Lignocellulosic biomass has demonstrated great potential as feedstock for pellet production, notwithstanding the fact that the industrial production of pellets is faced with some economic challenges. This study presents a technoeconomic analysis of six case scenarios to develop a process model for pellet production from sawdust and oat straw that employs torrefaction and steam explosion pretreatment prior to pelletization. SuperPro Designer was used to carry out this evaluation. The pellet plants were designed to have a capacity of 9.09 t/h of sawdust and oat straw each. The pellet yield ranged from 59 kt– 72 kt/year. Scenarios analyzed included variations of steam explosion and torrefaction. In some scenarios materials were lost in the form of liquid and gas due to the pretreatment process. The breakdown of equipment purchase cost showed that the torrefaction reactor is the most expensive unit with about 51% of the purchase cost. Facility-dependent and feedstock costs were the major significant contributors to the pellet production cost. The profitability of pellet production as determined by the net present value (NPV), internal rate of return (IRR), and payback period and was found to be sensitive to variations in feedstock cost.
- 13 November 2023
- Published by MDPI AG in Preprints.org
Open AccessTechnoeconomic Analysis of Torrefaction and Steam Explosion Pretreatment Prior to Pelletization of Selected Biomass
Lignocellulosic biomass has demonstrated great potential as feedstock for pellet production, notwithstanding the fact that the industrial production of pellets is faced with some economic challenges. This study presents a technoeconomic analysis of six case scenarios to develop a process model for pellet production from sawdust and oat straw that employs torrefaction and steam explosion pretreatment prior to pelletization. SuperPro Designer was used to carry out this evaluation. The pellet plants were designed to have a capacity of 9.09 t/h of sawdust and oat straw each. The pellet yield ranged from 59 kt– 72 kt/year. Scenarios analyzed included variations of steam explosion and torrefaction. In some scenarios materials were lost in the form of liquid and gas due to the pretreatment process. The breakdown of equipment purchase cost showed that the torrefaction reactor is the most expensive unit with about 51% of the purchase cost. Facility-dependent and feedstock costs were the major significant contributors to the pellet production cost. The profitability of pellet production as determined by the net present value (NPV), internal rate of return (IRR), and payback period and was found to be sensitive to variations in feedstock cost.
- Open Access
Actualization and Adoption of Renewable Energy Usage in Remote Communities in Canada by 2050: A Review
Remote community initiatives for renewable energy are rapidly emerging across Canada but with varying numbers, success rates, and strategies. To meet low-carbon transition goals, the need to coordinate technology deployment and long-term policy to guide the adoption is critical. Renewable resources such as wind, solar, hydro, and biomass can provide energy at a subsidized cost, create sustainable infrastructure, and provide new economic viability in social value integration. The renewable energy transition is crucial to Canada in sustaining remote and indigenous communities by providing local, clean, and low-carbon-emission energy for heat, power, and possibly transportation. This paper identified 635 renewable resources projects deployed to improve and increase electricity supply. To an extent, balancing demand within the remote and indigenous communities of Canada and highlighting sustainable renewable energy development through ownership participation within the communities is achievable before 2050 and beyond through energy efficiency and the social value of energy. The article identifies clean energy targets as mandated by the different provinces in Canada to reach net-zero GHG emissions.
Open AccessActualization and Adoption of Renewable Energy Usage in Remote Communities in Canada by 2050: A Review
Remote community initiatives for renewable energy are rapidly emerging across Canada but with varying numbers, success rates, and strategies. To meet low-carbon transition goals, the need to coordinate technology deployment and long-term policy to guide the adoption is critical. Renewable resources such as wind, solar, hydro, and biomass can provide energy at a subsidized cost, create sustainable infrastructure, and provide new economic viability in social value integration. The renewable energy transition is crucial to Canada in sustaining remote and indigenous communities by providing local, clean, and low-carbon-emission energy for heat, power, and possibly transportation. This paper identified 635 renewable resources projects deployed to improve and increase electricity supply. To an extent, balancing demand within the remote and indigenous communities of Canada and highlighting sustainable renewable energy development through ownership participation within the communities is achievable before 2050 and beyond through energy efficiency and the social value of energy. The article identifies clean energy targets as mandated by the different provinces in Canada to reach net-zero GHG emissions.
- Open Access
Effect of Torrefaction on the Physiochemical Properties of White Spruce Sawdust for Biofuel Production
Torrefaction pretreatment is a mild form of pyrolysis that has the potential to produce a high-quality raw material for making biofuel that serves as a replacement for coal in the bioenergy industry. Microwave-assisted torrefaction was conducted on white spruce sawdust (WSS) at temperatures of 200 °C, 250 °C, and 300 °C and retention times of 5 min, 7 min, and 9 min in an inert environment. The torrefaction process produces a solid carbon, commonly known as biochar, and condensable (torrefaction liquid (TL)) and non-condensable gases. In this study, torrefaction characteristics were investigated to observe its effects on the thermal and physiochemical properties of the pellets produced. During the torrefaction process, a significant mass loss associated with the decomposition of hemicellulose was observed. The hemicellulose content drastically reduced to approximately 1.8% and the cellulose content was reduced by approximately 10%, while the lignin gained approximately 35% as the severity increased. This led to an improvement in the higher heating value (HHV), hydrophobicity, bulk, particle density, pellet dimensional stability, and pellet density. However, the pellet tensile strength decreased as the torrefaction severity increased. Pellet tensile strength is a critical indicator of biomass pellets that expresses the force required to crush or damage a pellet. Therefore, to enhance the tensile strength of the pellets, the introduction of a binder was necessary. Torrefaction liquid and sawdust were used as additives at different proportions during pelletization. The addition of binders (torrefaction liquid and sawdust) to the pellet formulation increased the tensile strength of the torrefied WSS by approximately 50%. The OH groups in the biomass break down to a limited degree due to dehydration. This hinders the formation of H bonds, thereby increasing the chances that the pretreated biomass will become hydrophobic. The SEM graphs showed that the torrefied WSS pellets demonstrated more firmly glued surfaces with fewer pores spaces when set side by side with the raw pellets. The thermogravimetric analysis conducted showed that the torrefaction of WSS slightly reduced its thermal stability.
Open AccessEffect of Torrefaction on the Physiochemical Properties of White Spruce Sawdust for Biofuel Production
Torrefaction pretreatment is a mild form of pyrolysis that has the potential to produce a high-quality raw material for making biofuel that serves as a replacement for coal in the bioenergy industry. Microwave-assisted torrefaction was conducted on white spruce sawdust (WSS) at temperatures of 200 °C, 250 °C, and 300 °C and retention times of 5 min, 7 min, and 9 min in an inert environment. The torrefaction process produces a solid carbon, commonly known as biochar, and condensable (torrefaction liquid (TL)) and non-condensable gases. In this study, torrefaction characteristics were investigated to observe its effects on the thermal and physiochemical properties of the pellets produced. During the torrefaction process, a significant mass loss associated with the decomposition of hemicellulose was observed. The hemicellulose content drastically reduced to approximately 1.8% and the cellulose content was reduced by approximately 10%, while the lignin gained approximately 35% as the severity increased. This led to an improvement in the higher heating value (HHV), hydrophobicity, bulk, particle density, pellet dimensional stability, and pellet density. However, the pellet tensile strength decreased as the torrefaction severity increased. Pellet tensile strength is a critical indicator of biomass pellets that expresses the force required to crush or damage a pellet. Therefore, to enhance the tensile strength of the pellets, the introduction of a binder was necessary. Torrefaction liquid and sawdust were used as additives at different proportions during pelletization. The addition of binders (torrefaction liquid and sawdust) to the pellet formulation increased the tensile strength of the torrefied WSS by approximately 50%. The OH groups in the biomass break down to a limited degree due to dehydration. This hinders the formation of H bonds, thereby increasing the chances that the pretreated biomass will become hydrophobic. The SEM graphs showed that the torrefied WSS pellets demonstrated more firmly glued surfaces with fewer pores spaces when set side by side with the raw pellets. The thermogravimetric analysis conducted showed that the torrefaction of WSS slightly reduced its thermal stability.
- Open Access
Technoeconomic Feasibility of Bioenergy Production from Wood Sawdust
In this study, the technoeconomic feasibility of bioenergy production from sawdust under four different case scenarios is simulated and compared. These scenarios include: (1) heat and electricity generation from raw sawdust; (2) pellet production from sawdust; (3) and (4) integrated biorefinery approach for the simultaneous manufacturing of multiple products (steam-exploded and torrefied pellets) and co-products (furfural, hydroxy methyl furfural (HMF), acetic acid), along with heat and electricity generation. Economic assessments such as cost analysis, payback time (PBT), net present value (NPV) and internal rate of return (IRR) were determined for these scenarios. The results showed that the approach of producing torrefied pellets, furfural, and acetic acid, along with co-generated heat and electricity, in terms of multiproducts and profitability (NPV (at 7%): USD 38.29 M) was preferable over other alternatives. In terms of simplified technology and other economic indices (PBT: 2.49 year, IRR: 51.33%, and return on investment (ROI): 40.1%), the scenario for producing pellets from wood sawdust was more promising than others. If plant capacity was not a limiting factor, the optimal size for the combined heat and power (CHP) plant was between 250–300 kt for the main product. Additionally, untreated and treated pellet plants equipped with CHP had an optimal size of 150–200 kt of wood pellets per year.
Open AccessTechnoeconomic Feasibility of Bioenergy Production from Wood Sawdust
In this study, the technoeconomic feasibility of bioenergy production from sawdust under four different case scenarios is simulated and compared. These scenarios include: (1) heat and electricity generation from raw sawdust; (2) pellet production from sawdust; (3) and (4) integrated biorefinery approach for the simultaneous manufacturing of multiple products (steam-exploded and torrefied pellets) and co-products (furfural, hydroxy methyl furfural (HMF), acetic acid), along with heat and electricity generation. Economic assessments such as cost analysis, payback time (PBT), net present value (NPV) and internal rate of return (IRR) were determined for these scenarios. The results showed that the approach of producing torrefied pellets, furfural, and acetic acid, along with co-generated heat and electricity, in terms of multiproducts and profitability (NPV (at 7%): USD 38.29 M) was preferable over other alternatives. In terms of simplified technology and other economic indices (PBT: 2.49 year, IRR: 51.33%, and return on investment (ROI): 40.1%), the scenario for producing pellets from wood sawdust was more promising than others. If plant capacity was not a limiting factor, the optimal size for the combined heat and power (CHP) plant was between 250–300 kt for the main product. Additionally, untreated and treated pellet plants equipped with CHP had an optimal size of 150–200 kt of wood pellets per year.
- Open Access
Optimization of Solid-State Fermentation of Switchgrass Using White-Rot Fungi for Biofuel Production
Biological delignification using white-rot fungi is a possible approach in the pretreatment of lignocellulosic biomass. Despite the considerable promise of this low-input, environmentally-friendly pretreatment strategy, its large-scale application is still limited. Therefore, understanding the best combination of factors which affect biological pretreatment and its impact on enzymatic hydrolysis is essential for its commercialization. The present study was conducted to evaluate the impact of fungal pretreatment on the enzymatic digestibility of switchgrass under solid-state fermentation (SSF) using Phanerochaete chrysosporium (PC), Trametes versicolor 52J (Tv 52J), and a mutant strain of Trametes versicolor that is cellobiose dehydrogenase-deficient (Tv m4D). Response surface methodology and analysis of variance (ANOVA) were employed to ascertain the optimum pretreatment conditions and the effects of pretreatment factors on delignification, cellulose loss, and total available carbohydrate (TAC). Pretreatment with Tv m4D gave the highest TAC (73.4%), while the highest delignification (23.6%) was observed in the PC-treated sample. Fermentation temperature significantly affected the response variables for the wild-type fungal strains, while fermentation time was the main significant factor for Tv m4D. The result of enzymatic hydrolysis with fungus-treated switchgrass at optimum pretreatment conditions showed that pretreatment with the white-rot fungi enhanced enzymatic digestibility with wild-type T. versicolor (52J)-treated switchgrass, yielding approximately 64.9% and 74% more total reducing sugar before and after densification, respectively, than the untreated switchgrass sample. Pretreatment using PC and Tv 52J at low severity positively contributed to enzymatic digestibility but resulted in switchgrass pellets with low unit density and tensile strength compared to the pellets from the untreated switchgrass.
Open AccessOptimization of Solid-State Fermentation of Switchgrass Using White-Rot Fungi for Biofuel Production
Biological delignification using white-rot fungi is a possible approach in the pretreatment of lignocellulosic biomass. Despite the considerable promise of this low-input, environmentally-friendly pretreatment strategy, its large-scale application is still limited. Therefore, understanding the best combination of factors which affect biological pretreatment and its impact on enzymatic hydrolysis is essential for its commercialization. The present study was conducted to evaluate the impact of fungal pretreatment on the enzymatic digestibility of switchgrass under solid-state fermentation (SSF) using Phanerochaete chrysosporium (PC), Trametes versicolor 52J (Tv 52J), and a mutant strain of Trametes versicolor that is cellobiose dehydrogenase-deficient (Tv m4D). Response surface methodology and analysis of variance (ANOVA) were employed to ascertain the optimum pretreatment conditions and the effects of pretreatment factors on delignification, cellulose loss, and total available carbohydrate (TAC). Pretreatment with Tv m4D gave the highest TAC (73.4%), while the highest delignification (23.6%) was observed in the PC-treated sample. Fermentation temperature significantly affected the response variables for the wild-type fungal strains, while fermentation time was the main significant factor for Tv m4D. The result of enzymatic hydrolysis with fungus-treated switchgrass at optimum pretreatment conditions showed that pretreatment with the white-rot fungi enhanced enzymatic digestibility with wild-type T. versicolor (52J)-treated switchgrass, yielding approximately 64.9% and 74% more total reducing sugar before and after densification, respectively, than the untreated switchgrass sample. Pretreatment using PC and Tv 52J at low severity positively contributed to enzymatic digestibility but resulted in switchgrass pellets with low unit density and tensile strength compared to the pellets from the untreated switchgrass.
- Open Access
- 15 November 2022
- Published by MDPI AG in Clean Technologies
- Vol. 4 (4) , 1175-1192
Steam Explosion Pre-Treatment of Sawdust for Biofuel Pellets
The current study explores steam explosion pre-treatment of wood sawdust to develop high-quality biofuel pellets. In order to determine optimized conditions (temperature and residence time) for steam-treated biomass, seven test responses were chosen, including bulk, particle and pellet densities as well as tensile strength, dimensional stability, ash content and higher heating value (HHV). Parameters tested for steam treatment process included the combination of temperatures 180, 200 and 220 °C and durations of 3, 6 and 9 min. Results showed that when the severity of steam pre-treatment increased from 2.83 to 4.49, most of the qualities except HHV and ash content were favorable for steam pretreated materials. The pellet density of pretreated sawdust in comparison to raw sawdust resulted in 20% improvement (1262 kg/m3 for pretreated material compared with 1049 kg/m3 for non-treated material). Another important factor in determining the best pellet quality is tensile strength, which can be as high as 5.59 MPa for pretreated pellets compared with 0.32 MPa for non-treated pellets. As a result, transportation and handling properties can be enhanced for steam pretreated biomass pellets. After optimization, the selected treatment was analyzed for elemental and chemical composition. Lower nitrogen and sulfur contents compared with fossil fuels make steam pretreated pellets a cleaner option for home furnaces and industrial boilers. High-quality pellets were produced based on optimized pre-treatment conditions and are therefore suggested for bioenergy applications.
- 15 November 2022
- Published by MDPI AG in Clean Technologies
- Vol. 4 (4) , 1175-1192
Open AccessSteam Explosion Pre-Treatment of Sawdust for Biofuel Pellets
The current study explores steam explosion pre-treatment of wood sawdust to develop high-quality biofuel pellets. In order to determine optimized conditions (temperature and residence time) for steam-treated biomass, seven test responses were chosen, including bulk, particle and pellet densities as well as tensile strength, dimensional stability, ash content and higher heating value (HHV). Parameters tested for steam treatment process included the combination of temperatures 180, 200 and 220 °C and durations of 3, 6 and 9 min. Results showed that when the severity of steam pre-treatment increased from 2.83 to 4.49, most of the qualities except HHV and ash content were favorable for steam pretreated materials. The pellet density of pretreated sawdust in comparison to raw sawdust resulted in 20% improvement (1262 kg/m3 for pretreated material compared with 1049 kg/m3 for non-treated material). Another important factor in determining the best pellet quality is tensile strength, which can be as high as 5.59 MPa for pretreated pellets compared with 0.32 MPa for non-treated pellets. As a result, transportation and handling properties can be enhanced for steam pretreated biomass pellets. After optimization, the selected treatment was analyzed for elemental and chemical composition. Lower nitrogen and sulfur contents compared with fossil fuels make steam pretreated pellets a cleaner option for home furnaces and industrial boilers. High-quality pellets were produced based on optimized pre-treatment conditions and are therefore suggested for bioenergy applications.
- Open Access
Impact of Biochar Addition in Microwave Torrefaction of Camelina Straw and Switchgrass for Biofuel Production
The possibility of applying biochar in mild torrefaction treatment to improve the thermochemical characteristics of ground biomass was the focus of the study. Camelina straw and switchgrass were torrefied in a reactor using microwave irradiation at torrefaction temperatures of 250 °C and 300 °C with residence times 10, 15 and 20 min, under nitrogen-activated inert conditions. Both biochar addition of more than 10% and residence time significantly affected the product yields, as MW torrefaction temperatures shifted from 250 °C to 300 °C. Overall, the results indicated a slight increase in ash content, mass loss percentage intensification, heating values, and fixed carbon, while moisture content and volatile matter decreased in camelina straw and switchgrass, with or without biochar. Biochar addition with a long residence time (20 min) at 250 °C reduced energy requirement during the microwave torrefaction process. The combustion index values showed that torrefied camelina straw or switchgrass with biochar addition suits co-combustion with coal in a coal-fired plant and is a potential biomaterial for biofuel pellets.
Open AccessImpact of Biochar Addition in Microwave Torrefaction of Camelina Straw and Switchgrass for Biofuel Production
The possibility of applying biochar in mild torrefaction treatment to improve the thermochemical characteristics of ground biomass was the focus of the study. Camelina straw and switchgrass were torrefied in a reactor using microwave irradiation at torrefaction temperatures of 250 °C and 300 °C with residence times 10, 15 and 20 min, under nitrogen-activated inert conditions. Both biochar addition of more than 10% and residence time significantly affected the product yields, as MW torrefaction temperatures shifted from 250 °C to 300 °C. Overall, the results indicated a slight increase in ash content, mass loss percentage intensification, heating values, and fixed carbon, while moisture content and volatile matter decreased in camelina straw and switchgrass, with or without biochar. Biochar addition with a long residence time (20 min) at 250 °C reduced energy requirement during the microwave torrefaction process. The combustion index values showed that torrefied camelina straw or switchgrass with biochar addition suits co-combustion with coal in a coal-fired plant and is a potential biomaterial for biofuel pellets.
- Open Access
Investigation of Steam Explosion Pretreatment of Sawdust and Oat Straw to Improve Their Quality as Biofuel Pellets
Steam explosion pretreatment of sawdust and oat straw under mild, medium, and severe conditions was conducted to improve the quality of pellets generated from these feedstocks. This work examined the effects of temperature, time, and moisture content on the mechanical properties of biomass pellets. From the ANOVA conducted, the p-values of the regression models for all the response variables (dimensional stability, tensile strength, and pellet density) studied were significant (p < 0.05), except for the pellet density of steam-pretreated oat straw pellets. The interaction of these three factors did not significantly affect the response variables of oat straw pellets. In addition, the higher heating value (HHV) of treated biomass increased up to a maximum of about 9.5% and 7% as compared with the non-treated sawdust and oat straw, respectively. In addition, an increment of about 3.6-fold and 3.1-fold in pellet tensile strength of steam-pretreated sawdust and oat straw was observed, respectively. Microstructural examination of the pellets from steam-pretreated biomass revealed that the material contained particles that were more closely bonded and featured a cemented surface with fewer pores when compared to particles from untreated oat straw and sawdust.
Open AccessInvestigation of Steam Explosion Pretreatment of Sawdust and Oat Straw to Improve Their Quality as Biofuel Pellets
Steam explosion pretreatment of sawdust and oat straw under mild, medium, and severe conditions was conducted to improve the quality of pellets generated from these feedstocks. This work examined the effects of temperature, time, and moisture content on the mechanical properties of biomass pellets. From the ANOVA conducted, the p-values of the regression models for all the response variables (dimensional stability, tensile strength, and pellet density) studied were significant (p < 0.05), except for the pellet density of steam-pretreated oat straw pellets. The interaction of these three factors did not significantly affect the response variables of oat straw pellets. In addition, the higher heating value (HHV) of treated biomass increased up to a maximum of about 9.5% and 7% as compared with the non-treated sawdust and oat straw, respectively. In addition, an increment of about 3.6-fold and 3.1-fold in pellet tensile strength of steam-pretreated sawdust and oat straw was observed, respectively. Microstructural examination of the pellets from steam-pretreated biomass revealed that the material contained particles that were more closely bonded and featured a cemented surface with fewer pores when compared to particles from untreated oat straw and sawdust.