Andrés Biedma-Pérez
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Andrés Biedma-Pérez has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Ángel Palomares-Caballero
Department of Signal Theory, Telematics and Communications, Centre for Information and Communication Technologies (CITIC-UGR), University of Granada, Granada, Spain
9 shared publications - Pablo Padilla
Department of Signal Theory, Telematics and Communications, Centre for Information and Communication Technologies (CITIC-UGR), University of Granada, Granada, Spain
7 shared publications - Cleofás Segura-Gómez
Department of Signal Theory, Telematics and Communications. Research Centre for Information and Communication Technologies, University of Granada, Granada, Spain
6 shared publications - Mario Pérez-Escribano
Departamento de Ingeniería de Comunicaciones, Escuela Técnica Superior de Ingeniería de Telecomunicación, Universidad de Málaga
2 shared publications Pablo Padilla
2 shared publications- Carlos Molero
Department of Electronics and Electromagnetism Faculty of Physics, University of Seville, Seville, Spain
1 shared publication
Latest Publications
- Open Access
- 27 October 2026
- Published by Elsevier in SSRN Electronic Journal
Millimeter-Wave Transmitarray Using Post-Wall Slotline Technology
This paper presents a transmitarray (TA) operating around 40 GHz, in the 5G FR2 bands n259 andn260, built from interchangeable printed circuit board (PCB) plates in post-wall slotline (PWS)technology. The unit cell is a meandered PWS delay line whose transmission phase is set only bythe meander amplitude. The metallization of both faces keeps the air gaps between adjacent platesbelow cut-off, and two via fences confine the guided field within each plate. Eight unit cells providea 3-bit phase resolution, with a simulated reflection coefficient below -15 dB and an insertion lossof about 1 dB over 37–43.5 GHz. Each of the 15 plates holds 15 identical unit cells in a single phasestate, so the H-plane beam direction is reconfigured by reordering the plates. A full-wave simulation ofthe complete aperture confirms that each plate keeps its periodic response. With four plates per state,the fabricated prototype steers the beam over 4◦–38◦ and 42◦–50◦. Measured in four configurationsfrom 10◦ to 42◦, the beams point within 1.2◦ of their targets at 40 GHz, with side-lobe levels of about-10 dB, and the estimated directivity agrees with simulation within 0.4 dB on average.
- 27 October 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessMillimeter-Wave Transmitarray Using Post-Wall Slotline Technology
This paper presents a transmitarray (TA) operating around 40 GHz, in the 5G FR2 bands n259 andn260, built from interchangeable printed circuit board (PCB) plates in post-wall slotline (PWS)technology. The unit cell is a meandered PWS delay line whose transmission phase is set only bythe meander amplitude. The metallization of both faces keeps the air gaps between adjacent platesbelow cut-off, and two via fences confine the guided field within each plate. Eight unit cells providea 3-bit phase resolution, with a simulated reflection coefficient below -15 dB and an insertion lossof about 1 dB over 37–43.5 GHz. Each of the 15 plates holds 15 identical unit cells in a single phasestate, so the H-plane beam direction is reconfigured by reordering the plates. A full-wave simulation ofthe complete aperture confirms that each plate keeps its periodic response. With four plates per state,the fabricated prototype steers the beam over 4◦–38◦ and 42◦–50◦. Measured in four configurationsfrom 10◦ to 42◦, the beams point within 1.2◦ of their targets at 40 GHz, with side-lobe levels of about-10 dB, and the estimated directivity agrees with simulation within 0.4 dB on average.
- Open Access
- 29 September 2026
- Published by Elsevier in SSRN Electronic Journal
K-band Reflection-type Attenuator Controlled by a single P-I-N diode
This paper presents a design approach for K-band reflection-type variable attenuator based on the bias voltage of a single p-i-n diode. At millimeter-wave frequencies, parasitic effects mask the intrinsic diode resistance, which can be effectively used to produce the attenuation. To overcome this, a hybrid design strategy is proposed, combining full-wave and circuit simulations. The proposed variable attenuator is implemented in microstrip technology. Its layout is optimized to achieve more than 10 dB attenuation difference between the OFF and conducting states of the p-i-n diode at 25 GHz. The proposed variable attenuator is fabricated and experimentally verified. The measured performance demonstrates a dynamic attenuation range from 0.89~dB to 25 dB at 24.8 GHz. A continuous attenuation greater than 10 dB is also achieved across the 24.34 - 25.4~GHz band by tuning the DC bias voltage from -1 V to 1.4 V.
- 29 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessK-band Reflection-type Attenuator Controlled by a single P-I-N diode
This paper presents a design approach for K-band reflection-type variable attenuator based on the bias voltage of a single p-i-n diode. At millimeter-wave frequencies, parasitic effects mask the intrinsic diode resistance, which can be effectively used to produce the attenuation. To overcome this, a hybrid design strategy is proposed, combining full-wave and circuit simulations. The proposed variable attenuator is implemented in microstrip technology. Its layout is optimized to achieve more than 10 dB attenuation difference between the OFF and conducting states of the p-i-n diode at 25 GHz. The proposed variable attenuator is fabricated and experimentally verified. The measured performance demonstrates a dynamic attenuation range from 0.89~dB to 25 dB at 24.8 GHz. A continuous attenuation greater than 10 dB is also achieved across the 24.34 - 25.4~GHz band by tuning the DC bias voltage from -1 V to 1.4 V.
- Open Access
- 3 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 114901-114910
Compact H-Plane CLAF-SIW Horn Antenna With Phase Front Correction
This work presents an H-plane contactless air-filled substrate-integrated waveguide (CLAF-SIW) horn antenna, whose directivity is enhanced by incorporating a metalens along the horn flaring. By tuning the distribution of the unit cells of the metalens, it is possible to reduce phase errors at the aperture, a common issue in horn antennas. The unit cell of the metalens is designed by using a metallic patch on a substrate-integrated hole. By varying the size of the metal patches, different refraction indices can be tuned, resulting in a wideband performance. An analysis of the distribution of these unit cells along the horn antenna is conducted to achieve the desired equivalent effective refraction index through the metalens. The directivity achieved is comparable to that of a horn antenna with optimal dimensions, but with a 41% reduction in length. The measured results demonstrate an impedance bandwidth below −10 dB from 32.8 to 50 GHz, with a realized gain above 9.3 dBi.
- 3 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 114901-114910
Open AccessCompact H-Plane CLAF-SIW Horn Antenna With Phase Front Correction
This work presents an H-plane contactless air-filled substrate-integrated waveguide (CLAF-SIW) horn antenna, whose directivity is enhanced by incorporating a metalens along the horn flaring. By tuning the distribution of the unit cells of the metalens, it is possible to reduce phase errors at the aperture, a common issue in horn antennas. The unit cell of the metalens is designed by using a metallic patch on a substrate-integrated hole. By varying the size of the metal patches, different refraction indices can be tuned, resulting in a wideband performance. An analysis of the distribution of these unit cells along the horn antenna is conducted to achieve the desired equivalent effective refraction index through the metalens. The directivity achieved is comparable to that of a horn antenna with optimal dimensions, but with a 41% reduction in length. The measured results demonstrate an impedance bandwidth below −10 dB from 32.8 to 50 GHz, with a realized gain above 9.3 dBi.
- Open Access
- 2 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 24 (9) , 3183-3187
Substrate Integrated Monopulse Leaky Horn Antenna
This paper presents a leaky horn antenna based on a substrate integrated waveguide (SIW) with monopulse performance. The proposed leaky horn antenna consists of two SIW leaky-wave antennas (LWAs) angularly separated to form the horn's flaring. By properly designing this angular separation taking into account the main radiation direction of both LWAs, a flat wavefront is achieved in the leaky horn aperture. To provide the monopulse behavior to the SIW leaky horn, a hybrid coupler, and phase shifters are included in the feeding. Depending on the input port chosen on the hybrid coupler, the LWAs forming the leaky horn are fed in phase or counter-phase and generate the sum and difference radiation patterns. A prototype has been fabricated to validate the design. In the operating band, an impedance matching below −13.9 dB is achieved at both input ports with an isolation between ports better than 16.6 dB. The measured radiation patterns show a monopulse behavior with a proper agreement with the simulated results. The proposed leaky horn presents a depth of −25.8 dB (difference between the sum diagram and the difference in the boresight axis), a peak realized gain of 12.9 dBi, and a half-power beamwidth of 6.4° at 27.5 GHz.
- 2 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 24 (9) , 3183-3187
Open AccessSubstrate Integrated Monopulse Leaky Horn Antenna
This paper presents a leaky horn antenna based on a substrate integrated waveguide (SIW) with monopulse performance. The proposed leaky horn antenna consists of two SIW leaky-wave antennas (LWAs) angularly separated to form the horn's flaring. By properly designing this angular separation taking into account the main radiation direction of both LWAs, a flat wavefront is achieved in the leaky horn aperture. To provide the monopulse behavior to the SIW leaky horn, a hybrid coupler, and phase shifters are included in the feeding. Depending on the input port chosen on the hybrid coupler, the LWAs forming the leaky horn are fed in phase or counter-phase and generate the sum and difference radiation patterns. A prototype has been fabricated to validate the design. In the operating band, an impedance matching below −13.9 dB is achieved at both input ports with an isolation between ports better than 16.6 dB. The measured radiation patterns show a monopulse behavior with a proper agreement with the simulated results. The proposed leaky horn presents a depth of −25.8 dB (difference between the sum diagram and the difference in the boresight axis), a peak realized gain of 12.9 dBi, and a half-power beamwidth of 6.4° at 27.5 GHz.
- Open Access
- 5 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 24 (7) , 1824-1828
Metal-Only 3-D Unit Cell for Reflectarrays With Independent Dual-Band Operation
This paper presents a metal-only reflectarray based on a 3D unit cell with dual-band capability. The 3D unit cell is a square waveguide whose vertical walls include resonator elements with independent frequency performance. Different resonator geometries are analyzed to obtain a reflected phase variation in the target frequency band and to be feasible for 3-D manufacturing. $C$-shaped, triangle-shaped, and circle-shaped resonators are selected to obtain the required phase shift in reflection. A reflectarray (RA) prototype is designed, including pairs of resonators where the $C$-shaped resonator controls the low-frequency band, and the triangle resonators do so for the high-frequency band. The main reflected beam directions for each frequency band are different to show the independent phase tuning of the resonators. The prototype is manufactured using stereolithography (SLA) with a subsequent silver coating. Measured results show realized gains of 21.2 dBi in the 18 GHz band and 23.63 dBi in the 26.75 GHz band, with a good agreement with the simulated results.
- 5 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 24 (7) , 1824-1828
Open AccessMetal-Only 3-D Unit Cell for Reflectarrays With Independent Dual-Band Operation
This paper presents a metal-only reflectarray based on a 3D unit cell with dual-band capability. The 3D unit cell is a square waveguide whose vertical walls include resonator elements with independent frequency performance. Different resonator geometries are analyzed to obtain a reflected phase variation in the target frequency band and to be feasible for 3-D manufacturing. $C$-shaped, triangle-shaped, and circle-shaped resonators are selected to obtain the required phase shift in reflection. A reflectarray (RA) prototype is designed, including pairs of resonators where the $C$-shaped resonator controls the low-frequency band, and the triangle resonators do so for the high-frequency band. The main reflected beam directions for each frequency band are different to show the independent phase tuning of the resonators. The prototype is manufactured using stereolithography (SLA) with a subsequent silver coating. Measured results show realized gains of 21.2 dBi in the 18 GHz band and 23.63 dBi in the 26.75 GHz band, with a good agreement with the simulated results.
- Open Access
- 22 February 2025
- Published by Elsevier in AEU - International Journal of Electronics and Communications
- Vol. 193
Cavity-stacked filter in CLAF-SIW technology for millimeter waves
- 22 February 2025
- Published by Elsevier in AEU - International Journal of Electronics and Communications
- Vol. 193
Open AccessCavity-stacked filter in CLAF-SIW technology for millimeter waves
- Open Access
- 11 May 2024
- Published by Elsevier in AEU - International Journal of Electronics and Communications
- Vol. 179
Contactless AF-SIW phase shifters based on periodic structures at mmWaves
- 11 May 2024
- Published by Elsevier in AEU - International Journal of Electronics and Communications
- Vol. 179
Open AccessContactless AF-SIW phase shifters based on periodic structures at mmWaves
- Open Access
- 17 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in TechRxiv
Holey SIW Horn Antenna Based on an H-plane Lens-wise Wavefront Collimation
This paper presents an H-plane SIW horn antenna whose directivity is enhanced using holey unit cells along the horn flaring. By wisely drilling the horn antenna, it is possible to reduce the phase error in the aperture which is a common problem in horn antennas if the optimum dimensions are not employed. An analysis of the distribution of the unit cells along the horn antenna has been carried out to achieve the desired equivalent refractive indices. By changing the hole radius, different equivalent refractive indices can be tuned with a wideband performance. This fact enables the implementation of a collimation zone inside the horn antenna which transforms the pseudo-circular wavefront into a quasi-planar one in the radiating aperture. The produced directivity is similar to the horn antenna with the optimum dimensions but a longitudinal reduction of 53.7% and a higher realized gain are achieved. A holey SIW horn antenna is designed and manufactured. The measured results show an impedance bandwidth performance below -10 dB from 34.3 GHz to 44.5 GHz (25.9%) with a realized gain above 10 dBi. The gain difference regarding a SIW horn antenna without the collimation zone is about 2-3 dBi in the operating frequency range.
- 17 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in TechRxiv
Open AccessHoley SIW Horn Antenna Based on an H-plane Lens-wise Wavefront Collimation
This paper presents an H-plane SIW horn antenna whose directivity is enhanced using holey unit cells along the horn flaring. By wisely drilling the horn antenna, it is possible to reduce the phase error in the aperture which is a common problem in horn antennas if the optimum dimensions are not employed. An analysis of the distribution of the unit cells along the horn antenna has been carried out to achieve the desired equivalent refractive indices. By changing the hole radius, different equivalent refractive indices can be tuned with a wideband performance. This fact enables the implementation of a collimation zone inside the horn antenna which transforms the pseudo-circular wavefront into a quasi-planar one in the radiating aperture. The produced directivity is similar to the horn antenna with the optimum dimensions but a longitudinal reduction of 53.7% and a higher realized gain are achieved. A holey SIW horn antenna is designed and manufactured. The measured results show an impedance bandwidth performance below -10 dB from 34.3 GHz to 44.5 GHz (25.9%) with a realized gain above 10 dBi. The gain difference regarding a SIW horn antenna without the collimation zone is about 2-3 dBi in the operating frequency range.
- 5 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 71 (1) , 1023-1028
Holey SIW Horn Antenna Based on an H-Plane Lenswise Wavefront Collimation
This paper presents an H-plane SIW horn antenna whose directivity is enhanced using holey unit cells along the horn flaring. By wisely drilling the horn antenna, it is possible to reduce the phase error in the aperture which is a common problem in horn antennas if the optimum dimensions are not employed. An analysis of the distribution of the unit cells along the horn antenna has been carried out to achieve the desired equivalent refractive indices. By changing the hole radius, different equivalent refractive indices can be tuned with a wideband performance. This fact enables the implementation of a collimation zone inside the horn antenna which transforms the pseudo-circular wavefront into a quasi-planar one in the radiating aperture. The produced directivity is similar to the horn antenna with the optimum dimensions but a longitudinal reduction of 53.7% and a higher realized gain are achieved. A holey SIW horn antenna is designed and manufactured. The measured results show an impedance bandwidth performance below -10 dB from 34.3 GHz to 44.5 GHz (25.9%) with a realized gain above 10 dBi. The gain difference regarding a SIW horn antenna without the collimation zone is about 2-3 dBi in the operating frequency range.
- 5 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 71 (1) , 1023-1028
Holey SIW Horn Antenna Based on an H-Plane Lenswise Wavefront Collimation
This paper presents an H-plane SIW horn antenna whose directivity is enhanced using holey unit cells along the horn flaring. By wisely drilling the horn antenna, it is possible to reduce the phase error in the aperture which is a common problem in horn antennas if the optimum dimensions are not employed. An analysis of the distribution of the unit cells along the horn antenna has been carried out to achieve the desired equivalent refractive indices. By changing the hole radius, different equivalent refractive indices can be tuned with a wideband performance. This fact enables the implementation of a collimation zone inside the horn antenna which transforms the pseudo-circular wavefront into a quasi-planar one in the radiating aperture. The produced directivity is similar to the horn antenna with the optimum dimensions but a longitudinal reduction of 53.7% and a higher realized gain are achieved. A holey SIW horn antenna is designed and manufactured. The measured results show an impedance bandwidth performance below -10 dB from 34.3 GHz to 44.5 GHz (25.9%) with a realized gain above 10 dBi. The gain difference regarding a SIW horn antenna without the collimation zone is about 2-3 dBi in the operating frequency range.