Ting Xu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Ting Xu has a total of 42 co-authors. Here are the top co-authors by number of shared publications:
- Yefa Tan
College of Field Engineering, Army Engineering University of PLA, Nanjing 210007, China
4 shared publications Lizhou An
College of Field Engineering, Army Engineering University of PLA 1 , Nanjing, Jiangsu 210007
2 shared publications- Qin Yin
College of Field Engineering, Army Engineering University of PLA 1 , Nanjing, Jiangsu 210007
2 shared publications Yumin Jiao
94789 Troop of PLA 2 , Nanjing, Jiangsu 210018
2 shared publications- Bin Cai
Key Laboratory of Material Physics, Ministry of Education, School of Physics, Zhengzhou University, Zhengzhou 450001, China
1 shared publication - Ce Liu
College of Field Engineering, Army Engineering University of PLA , Nanjing 210007, Jiangsu
1 shared publication
Latest Publications
- Open Access
- 1 October 2026
- Published by AIP Publishing in AIP Advances
- Vol. 16 (10)
Effect of TiC particle content on microstructure and tribological properties of laser cladding TiC particle reinforced Ni60PTA alloy composite coating
To enhance the hardness and wear resistance of 45 steel surfaces, this study employed laser cladding technology to fabricate a TiC/Ni60PTA composite coating on 45 steel. The effects of varying TiC particle contents (0 wt. %, 5 wt. %, 15 wt. %, 25 wt. %, and 35 wt. %) on the macroscopic morphology, microstructure, phase composition, microhardness, and wear performance of the composite coating were investigated, with its wear mechanism elucidated. The results demonstrated that the TiC/Ni60PTA composite coating primarily consists of γ(Ni), FeNi3, CrB, M7C3 (M = Fe or Cr), M23C6, TiC, and TiCx phases. Compared to pure Ni60PTA alloy coatings, the microhardness of the composite coating increased initially and then decreased with increasing TiC particle content. Notably, the TC25 composite coating exhibited the highest microhardness (673.92 HV0.2), representing a 172% improvement over the base material. Its friction coefficient of wear dropped to 0.5465, a 25.95% reduction from the base material, while the weight loss during wear was minimized to 0.1 g, a 44.43% decrease. This performance was attributed to the uniform distribution of TiC particles in the composite coating, with the wear mechanism primarily involving adhesive wear and minor plastic deformation wear. Based on the comprehensive evaluation of microhardness and tribological properties, the TC25 composite coating exhibits the best wear resistance and can be considered the preferred choice for laser cladding TiC/Ni60PTA composite coatings on 45 steel surfaces. This provides a theoretical basis and technical support for the development and application of such composite coatings.
- 1 October 2026
- Published by AIP Publishing in AIP Advances
- Vol. 16 (10)
Open AccessEffect of TiC particle content on microstructure and tribological properties of laser cladding TiC particle reinforced Ni60PTA alloy composite coating
To enhance the hardness and wear resistance of 45 steel surfaces, this study employed laser cladding technology to fabricate a TiC/Ni60PTA composite coating on 45 steel. The effects of varying TiC particle contents (0 wt. %, 5 wt. %, 15 wt. %, 25 wt. %, and 35 wt. %) on the macroscopic morphology, microstructure, phase composition, microhardness, and wear performance of the composite coating were investigated, with its wear mechanism elucidated. The results demonstrated that the TiC/Ni60PTA composite coating primarily consists of γ(Ni), FeNi3, CrB, M7C3 (M = Fe or Cr), M23C6, TiC, and TiCx phases. Compared to pure Ni60PTA alloy coatings, the microhardness of the composite coating increased initially and then decreased with increasing TiC particle content. Notably, the TC25 composite coating exhibited the highest microhardness (673.92 HV0.2), representing a 172% improvement over the base material. Its friction coefficient of wear dropped to 0.5465, a 25.95% reduction from the base material, while the weight loss during wear was minimized to 0.1 g, a 44.43% decrease. This performance was attributed to the uniform distribution of TiC particles in the composite coating, with the wear mechanism primarily involving adhesive wear and minor plastic deformation wear. Based on the comprehensive evaluation of microhardness and tribological properties, the TC25 composite coating exhibits the best wear resistance and can be considered the preferred choice for laser cladding TiC/Ni60PTA composite coatings on 45 steel surfaces. This provides a theoretical basis and technical support for the development and application of such composite coatings.
- Open Access
- 1 October 2024
- Published by AIP Publishing in AIP Advances
- Vol. 14 (10)
Influence of different composite curing agents on the rapid curing characteristics and mechanical performance of epoxy resins
To address the need for rapid in situ plugging and repair of hydraulic machinery and chemical pipelines and to resolve the issue that a single curing agent cannot simultaneously achieve rapid curing and excellent mechanical properties in epoxy resin systems, this study explores the use of composite curing agents. In particular, effective formulations are designed for mixing fast and slow curing agents, studying their effects on the curing behavior, curing quality, and mechanical properties of epoxy resins and elucidating their influence mechanisms. The results indicate that three resin systems meet the requirements for rapid curing (curing time within 30 min): 4A6B/EP, 2A8B/EP, and 0A10B/EP. Among them, 4A6B/EP exhibits the best curing quality and mechanical properties. In particular, 4A6B/EP demonstrates the lowest values of curing shrinkage rate, internal curing stress, average pore size, porosity, and cumulative pore volume. Its low internal stress and low defects reduce the stress concentration, while more efficient deflection and branching of internal cracks enhance its deformation resistance. Consequently, 4A6B/EP shows the highest microhardness, fracture toughness, tensile strength, Young’s modulus, and elongation after fracture. Based on the comprehensive evaluation of rapid curing characteristics and mechanical properties, the 4A6B/EP system offers the best overall performance. Therefore, it is recommended as the preferred resin system for rapid plugging and repair of composite materials, providing a theoretical basis and technical support for boosting the application of epoxy resin composite materials in high-tech fields.
- 1 October 2024
- Published by AIP Publishing in AIP Advances
- Vol. 14 (10)
Open AccessInfluence of different composite curing agents on the rapid curing characteristics and mechanical performance of epoxy resins
To address the need for rapid in situ plugging and repair of hydraulic machinery and chemical pipelines and to resolve the issue that a single curing agent cannot simultaneously achieve rapid curing and excellent mechanical properties in epoxy resin systems, this study explores the use of composite curing agents. In particular, effective formulations are designed for mixing fast and slow curing agents, studying their effects on the curing behavior, curing quality, and mechanical properties of epoxy resins and elucidating their influence mechanisms. The results indicate that three resin systems meet the requirements for rapid curing (curing time within 30 min): 4A6B/EP, 2A8B/EP, and 0A10B/EP. Among them, 4A6B/EP exhibits the best curing quality and mechanical properties. In particular, 4A6B/EP demonstrates the lowest values of curing shrinkage rate, internal curing stress, average pore size, porosity, and cumulative pore volume. Its low internal stress and low defects reduce the stress concentration, while more efficient deflection and branching of internal cracks enhance its deformation resistance. Consequently, 4A6B/EP shows the highest microhardness, fracture toughness, tensile strength, Young’s modulus, and elongation after fracture. Based on the comprehensive evaluation of rapid curing characteristics and mechanical properties, the 4A6B/EP system offers the best overall performance. Therefore, it is recommended as the preferred resin system for rapid plugging and repair of composite materials, providing a theoretical basis and technical support for boosting the application of epoxy resin composite materials in high-tech fields.
- Open Access
Non-Covalent Functionalization of Graphene Oxide with POSS to Improve the Mechanical Properties of Epoxy Composites
Phenyl polyhedral oligomeric silsesquioxane (POSS) is modified onto the GO surface by using the strong π–π coupling between a large number of benzene rings at the end of the phenyl POSS structure and the graphite structure in the GO sheet, realizing the non-covalent functionalization of GO (POSS-GO). The POSS-GO-reinforced EP (POSS-GO/EP) composite material is prepared using the casting molding process. The surface morphology of GO before and after modification and its peel dispersion in EP are examined. Furthermore, the mechanical properties, cross-sectional morphology, and reinforcement mechanism of POSS-GO/EP are thoroughly examined. The results show that the cage-like skeleton structure of POSS is embedded between the GO layers, increasing the spacing between the GO layers and leading to a steric hindrance effect, which effectively prevents their stacking and aggregation and improves the dispersion performance of GO. In particular, the 0.4 phr POSS-GO/EP sample shows the best mechanical properties. This is because, on the one hand, POSS-GO is uniformly dispersed in the EP matrix, which can more efficiently induce crack deflection and bifurcation and can also cause certain plastic deformations in the EP matrix. On the other hand, the POSS-GO/EP fracture cross-section with a stepped morphology of interlaced “canine teeth” shape is rougher and more uneven, leading to more complex crack propagation paths and greater energy consumption. Moreover, the mechanical meshing effect between the rough POSS-GO surface and the EP matrix is stronger, which is conducive to the transfer of interfacial stress and the strengthening and toughening effects of POSS-GO.
Open AccessNon-Covalent Functionalization of Graphene Oxide with POSS to Improve the Mechanical Properties of Epoxy Composites
Phenyl polyhedral oligomeric silsesquioxane (POSS) is modified onto the GO surface by using the strong π–π coupling between a large number of benzene rings at the end of the phenyl POSS structure and the graphite structure in the GO sheet, realizing the non-covalent functionalization of GO (POSS-GO). The POSS-GO-reinforced EP (POSS-GO/EP) composite material is prepared using the casting molding process. The surface morphology of GO before and after modification and its peel dispersion in EP are examined. Furthermore, the mechanical properties, cross-sectional morphology, and reinforcement mechanism of POSS-GO/EP are thoroughly examined. The results show that the cage-like skeleton structure of POSS is embedded between the GO layers, increasing the spacing between the GO layers and leading to a steric hindrance effect, which effectively prevents their stacking and aggregation and improves the dispersion performance of GO. In particular, the 0.4 phr POSS-GO/EP sample shows the best mechanical properties. This is because, on the one hand, POSS-GO is uniformly dispersed in the EP matrix, which can more efficiently induce crack deflection and bifurcation and can also cause certain plastic deformations in the EP matrix. On the other hand, the POSS-GO/EP fracture cross-section with a stepped morphology of interlaced “canine teeth” shape is rougher and more uneven, leading to more complex crack propagation paths and greater energy consumption. Moreover, the mechanical meshing effect between the rough POSS-GO surface and the EP matrix is stronger, which is conducive to the transfer of interfacial stress and the strengthening and toughening effects of POSS-GO.
- Open Access
Effects of Air Plasma Modification on Aramid Fiber Surface and Its Composite Interface and Mechanical Properties
In order to improve the interface and mechanical properties of aramid fiber (AF)-reinforced epoxy resin (EP) composites (AF/EPs), the surface modification of AF was carried out with atmospheric pressure air plasma, and the effects of plasma treatment time and discharge power on the AF surface and the interface and mechanical properties of AF/EPs were investigated. The results show that, when plasma treatment time was 10 min and discharge power was 400 W, AF showed the best modification effect. Compared to the unmodified material, the total content of active groups on the surface of AF increased by 82.4%; the contact angle between AF and EP decreased by 20%; the interfacial energy and work of adhesion increased by 77.1% and 19.1%, respectively; the loss of AF monofilament tensile strength was controlled at only 8.6%; and the interlaminar shear strength and tensile strength of AF/EPs increased by 45.5% and 10.4%, respectively. The improvement in AF/EP interfacial and mechanical properties is due to the introduction of more active groups on the AF surface with suitable plasma processing parameters, which strengthens the chemical bonding between the AF and EP matrix. At the same time, plasma treatment effectively increases the surface roughness of AF, and the mechanical meshing effect between the AF and EP matrix is improved. The synergistic effect of chemical bonding and mechanical meshing improves the wettability and interfacial bonding strength between the AF and EP matrix, which enables the load to be transferred from the resin to the fiber more efficiently, thereby improving the mechanical properties of the AF/EP.
Open AccessEffects of Air Plasma Modification on Aramid Fiber Surface and Its Composite Interface and Mechanical Properties
In order to improve the interface and mechanical properties of aramid fiber (AF)-reinforced epoxy resin (EP) composites (AF/EPs), the surface modification of AF was carried out with atmospheric pressure air plasma, and the effects of plasma treatment time and discharge power on the AF surface and the interface and mechanical properties of AF/EPs were investigated. The results show that, when plasma treatment time was 10 min and discharge power was 400 W, AF showed the best modification effect. Compared to the unmodified material, the total content of active groups on the surface of AF increased by 82.4%; the contact angle between AF and EP decreased by 20%; the interfacial energy and work of adhesion increased by 77.1% and 19.1%, respectively; the loss of AF monofilament tensile strength was controlled at only 8.6%; and the interlaminar shear strength and tensile strength of AF/EPs increased by 45.5% and 10.4%, respectively. The improvement in AF/EP interfacial and mechanical properties is due to the introduction of more active groups on the AF surface with suitable plasma processing parameters, which strengthens the chemical bonding between the AF and EP matrix. At the same time, plasma treatment effectively increases the surface roughness of AF, and the mechanical meshing effect between the AF and EP matrix is improved. The synergistic effect of chemical bonding and mechanical meshing improves the wettability and interfacial bonding strength between the AF and EP matrix, which enables the load to be transferred from the resin to the fiber more efficiently, thereby improving the mechanical properties of the AF/EP.
- Open Access
- 29 September 2022
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 7 (40) , 35610-35625
Study on the Construction of Dopamine/Poly(ethyleneimine)/Aminoated Carbon Nanotube Multilayer Films on Aramid Fiber Surfaces to Improve the Mechanical Properties of Aramid Fibers/Epoxy Composites
- 29 September 2022
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 7 (40) , 35610-35625
Open AccessStudy on the Construction of Dopamine/Poly(ethyleneimine)/Aminoated Carbon Nanotube Multilayer Films on Aramid Fiber Surfaces to Improve the Mechanical Properties of Aramid Fibers/Epoxy Composites
- 1 May 2021
- Published by Elsevier in Optical Fiber Technology
- Vol. 63, 102531
No-core PDMS fiber for large-scale strain and concentration measurement
- 1 May 2021
- Published by Elsevier in Optical Fiber Technology
- Vol. 63, 102531
No-core PDMS fiber for large-scale strain and concentration measurement
- 1 April 2016
- Published by Elsevier in Applied Surface Science
- Vol. 369, 207-214
Tunable fabrication of hierarchical hybrids via the incorporation of poly(dopamine) functional interlayer
- 1 April 2016
- Published by Elsevier in Applied Surface Science
- Vol. 369, 207-214
Tunable fabrication of hierarchical hybrids via the incorporation of poly(dopamine) functional interlayer
- 1 August 2011
- Published by Elsevier in Transactions of Nonferrous Metals Society of China
- Vol. 21 (8) , 1741-1749
Effects of graphite content on microstructure and tribological properties of graphite/TiC/Ni-base alloy composite coatings
- 1 August 2011
- Published by Elsevier in Transactions of Nonferrous Metals Society of China
- Vol. 21 (8) , 1741-1749
Effects of graphite content on microstructure and tribological properties of graphite/TiC/Ni-base alloy composite coatings