Martin Mikolajčík
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Martin Mikolajčík has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Zuzana Šurdová
Department of Materials Engineering, Faculty of Mechanical Engineering, University of Žilina, Univerzitná 8215/1, 010 26 Žilina, Slovakia
8 shared publications - Eva Tillová
University of Žilina , Slovakia
7 shared publications - Lenka Kuchariková
Department of Materials Engineering, Faculty of Mechanical Engineering, University of Žilina, Univerzitná 8215/1, 010 26 Žilina, Slovakia
6 shared publications - Milan Uhríčik
University of Žilina
3 shared publications - Mária Chalupová
Department of Materials Engineering, Faculty of Mechanical Engineering, University of Žilina, Univerzitná 8215/1, 010 26 Žilina, Slovakia
3 shared publications - Jon Mikel Sanchez
TECNALIA, Basque Research and Technology Alliance (BRTA), Donostia 2009, Spain
2 shared publications
Latest Publications
- Open Access
Enhancing Fatigue Lifetime of Secondary AlZn10Si8Mg Alloys Through Shot Peening: Influence of Iron Content and Surface Defects
The rising demand for aluminium and environmental concerns highlight the need for a circular economy using recycled alloys. This study examines the effect of shot peening on the high-cycle fatigue life of secondary AlZn10Si8Mg alloys with different iron contents: Alloy A (0.14 wt.% Fe) and Alloy B (0.56 wt.% Fe). Although both alloys showed similar tensile properties, Alloy B had higher porosity and finer β-Al5FeSi intermetallics. Shot peening was applied at 100% and 1000% coverage to evaluate changes in surface roughness, porosity, residual stresses, and fatigue performance. The treatment significantly reduced surface-connected porosity via plastic deformation, enhancing fatigue life despite increased roughness. Fatigue tests showed a 21% increase in fatigue limit for Alloy A and a 6% gain for Alloy B at higher coverage. Fractographic analysis revealed that 95% of fatigue cracks initiated at surface pores. Residual stress measurements confirmed compressive stresses were limited to the near-surface layer, with minimal influence on subsurface crack propagation. Overall, shot peening proves to be an effective method for improving fatigue resistance in recycled aluminium alloys, even in alloys with elevated iron content, reinforcing their potential for structural applications under cyclic loading.
Open AccessEnhancing Fatigue Lifetime of Secondary AlZn10Si8Mg Alloys Through Shot Peening: Influence of Iron Content and Surface Defects
The rising demand for aluminium and environmental concerns highlight the need for a circular economy using recycled alloys. This study examines the effect of shot peening on the high-cycle fatigue life of secondary AlZn10Si8Mg alloys with different iron contents: Alloy A (0.14 wt.% Fe) and Alloy B (0.56 wt.% Fe). Although both alloys showed similar tensile properties, Alloy B had higher porosity and finer β-Al5FeSi intermetallics. Shot peening was applied at 100% and 1000% coverage to evaluate changes in surface roughness, porosity, residual stresses, and fatigue performance. The treatment significantly reduced surface-connected porosity via plastic deformation, enhancing fatigue life despite increased roughness. Fatigue tests showed a 21% increase in fatigue limit for Alloy A and a 6% gain for Alloy B at higher coverage. Fractographic analysis revealed that 95% of fatigue cracks initiated at surface pores. Residual stress measurements confirmed compressive stresses were limited to the near-surface layer, with minimal influence on subsurface crack propagation. Overall, shot peening proves to be an effective method for improving fatigue resistance in recycled aluminium alloys, even in alloys with elevated iron content, reinforcing their potential for structural applications under cyclic loading.
- Open Access
- 28 February 2025
- Published by Stowarzyszenie Menedzerow Jakosci i Produkcji in Production Engineering Archives
- Vol. 31 (1) , 54-64
Effect of Fe and Mn on Corrosion Resistance of Recycled Self-hardening AlZn10Si8Mg Alloy
Recycled aluminium alloys are a highly valued alternative for manufacturers, particularly in the automotive and aerospace industries, due to increasing demands on the environmental performance and sustainability of the industry. Self-hardening aluminium alloys, which achieve the required mechanical properties without heat treatment, enable the emissions generated by production to be reduced even further. In addition to an advantageous strength-to-weight ratio and excellent machinability, corrosion resistance in a variety of environments is also important in most applications of aluminium alloys. Repeated recycling cycles negatively influence the quality of aluminium because of an increase in iron content, which is considered an impurity. This is due to the formation of intermetallic phases which negatively affect the mechanical, fatigue and corrosion properties. In this paper, the effect of Fe and Mn on the microstructure and corrosion resistance of self-hardening recycled AlZn10Si8Mg alloy was investigated using the AUDI test, atmospheric long-terming test and 3.5% NaCl solution test. The corrosion mechanism was subsequently determined by sectioning the samples. Alloy A with the lowest iron content exhibited the best corrosion behaviour, as it was subjected to only localised forms of corrosion even in the aggressive environment of the AUDI test. In this environment, the other alloys were attacked by general corrosion of the entire surface. Manganese alloying caused a subtle improvement in the corrosion resistance of alloy D but was limited by the high porosity. The eutectic and intermetallic phases corroded the most, while the alpha phase was more resistant.
- 28 February 2025
- Published by Stowarzyszenie Menedzerow Jakosci i Produkcji in Production Engineering Archives
- Vol. 31 (1) , 54-64
Open AccessEffect of Fe and Mn on Corrosion Resistance of Recycled Self-hardening AlZn10Si8Mg Alloy
Recycled aluminium alloys are a highly valued alternative for manufacturers, particularly in the automotive and aerospace industries, due to increasing demands on the environmental performance and sustainability of the industry. Self-hardening aluminium alloys, which achieve the required mechanical properties without heat treatment, enable the emissions generated by production to be reduced even further. In addition to an advantageous strength-to-weight ratio and excellent machinability, corrosion resistance in a variety of environments is also important in most applications of aluminium alloys. Repeated recycling cycles negatively influence the quality of aluminium because of an increase in iron content, which is considered an impurity. This is due to the formation of intermetallic phases which negatively affect the mechanical, fatigue and corrosion properties. In this paper, the effect of Fe and Mn on the microstructure and corrosion resistance of self-hardening recycled AlZn10Si8Mg alloy was investigated using the AUDI test, atmospheric long-terming test and 3.5% NaCl solution test. The corrosion mechanism was subsequently determined by sectioning the samples. Alloy A with the lowest iron content exhibited the best corrosion behaviour, as it was subjected to only localised forms of corrosion even in the aggressive environment of the AUDI test. In this environment, the other alloys were attacked by general corrosion of the entire surface. Manganese alloying caused a subtle improvement in the corrosion resistance of alloy D but was limited by the high porosity. The eutectic and intermetallic phases corroded the most, while the alpha phase was more resistant.
- Open Access
- 16 February 2025
- Published by Walter de Gruyter GmbH in System Safety: Human - Technical Facility - Environment
- Vol. 7 (1) , 1-9
Improving the Properties of Recycled Self-Hardening Aluminium Alloy for Application in Electric Vehicles
In recent years, the topic of environmental issues has become increasingly important in all areas of industry. As a result of European Union policy, there has been a significant increase in the number of electric vehicles. At the same time, there is an increasing emphasis on ecological and sustainable production. Due to their advantageous strength-to-weight ratio, aluminium alloys are widely used in automobiles and are a logical choice for electric vehicles. Aluminium recycling is a very efficient way of reducing production costs and emissions. Self-hardening aluminium alloys enable heat treatment to be omitted, leading to further energy savings. The limiting factor of secondary production is the insufficient purity of aluminium scrap, which leads to contamination with impurities. In particular, the negative impact of iron, which is found in higher content in recycled alloys after repeated recycling cycles, is well known. Its presence leads to a deterioration of the mechanical, fatigue and corrosion properties of aluminium alloys. This work examines ways to reduce iron content in AlZn10Si8Mg self-hardening alloy using a sedimentation experiment. The crystallization temperature of iron phases is higher than that of the matrix. Therefore, holding the material at a specific temperature is expected to cause iron phases to settle, reducing the iron content.
- 16 February 2025
- Published by Walter de Gruyter GmbH in System Safety: Human - Technical Facility - Environment
- Vol. 7 (1) , 1-9
Open AccessImproving the Properties of Recycled Self-Hardening Aluminium Alloy for Application in Electric Vehicles
In recent years, the topic of environmental issues has become increasingly important in all areas of industry. As a result of European Union policy, there has been a significant increase in the number of electric vehicles. At the same time, there is an increasing emphasis on ecological and sustainable production. Due to their advantageous strength-to-weight ratio, aluminium alloys are widely used in automobiles and are a logical choice for electric vehicles. Aluminium recycling is a very efficient way of reducing production costs and emissions. Self-hardening aluminium alloys enable heat treatment to be omitted, leading to further energy savings. The limiting factor of secondary production is the insufficient purity of aluminium scrap, which leads to contamination with impurities. In particular, the negative impact of iron, which is found in higher content in recycled alloys after repeated recycling cycles, is well known. Its presence leads to a deterioration of the mechanical, fatigue and corrosion properties of aluminium alloys. This work examines ways to reduce iron content in AlZn10Si8Mg self-hardening alloy using a sedimentation experiment. The crystallization temperature of iron phases is higher than that of the matrix. Therefore, holding the material at a specific temperature is expected to cause iron phases to settle, reducing the iron content.
- Open Access
- 1 December 2024
- Published by Walter de Gruyter GmbH in System Safety: Human - Technical Facility - Environment
- Vol. 6 (1) , 430-438
The Study of Porosity in A356 Secondary Aluminium Alloys with Higher Iron Content
The production of secondary (recycled) aluminium has gained significant importance in recent years, driven by the need to reduce electricity consumption and waste associated with primary aluminium production. Secondary aluminium alloys thus play a vital role in sustainable industrial practices, particularly within sectors such as automotive, aerospace and marine. Recently, these alloys have gained traction in electric vehicle components manufacturing, where lightweight and sustainable materials are critical to enhancing energy efficiency and extending vehicle range. However, secondary aluminium alloys are prone to impurities and casting defects, notably porosity, which presents challenges in achieving optimal mechanical properties and surface quality. Porosity reduces corrosion resistance, fatigue, and tensile strength, thus impacting overall material performance. This porosity can be categorised by size (microporosity and macroporosity) and origin, with gas and shrinkage porosity being the primary types. This study examined experimental A356 secondary aluminium alloys with varying iron contents in as-cast and T6 heat-treated conditions. The analysis focused on the quantitative assessment of casting defects within the microstructure, specifically, the types of pores present, the area percentage of pores, and average pore size. These insights contribute to a deeper understanding of how casting defects impact the performance of recycled aluminium alloys in sustainable applications, particularly in the context of next-generation electric vehicles.
- 1 December 2024
- Published by Walter de Gruyter GmbH in System Safety: Human - Technical Facility - Environment
- Vol. 6 (1) , 430-438
Open AccessThe Study of Porosity in A356 Secondary Aluminium Alloys with Higher Iron Content
The production of secondary (recycled) aluminium has gained significant importance in recent years, driven by the need to reduce electricity consumption and waste associated with primary aluminium production. Secondary aluminium alloys thus play a vital role in sustainable industrial practices, particularly within sectors such as automotive, aerospace and marine. Recently, these alloys have gained traction in electric vehicle components manufacturing, where lightweight and sustainable materials are critical to enhancing energy efficiency and extending vehicle range. However, secondary aluminium alloys are prone to impurities and casting defects, notably porosity, which presents challenges in achieving optimal mechanical properties and surface quality. Porosity reduces corrosion resistance, fatigue, and tensile strength, thus impacting overall material performance. This porosity can be categorised by size (microporosity and macroporosity) and origin, with gas and shrinkage porosity being the primary types. This study examined experimental A356 secondary aluminium alloys with varying iron contents in as-cast and T6 heat-treated conditions. The analysis focused on the quantitative assessment of casting defects within the microstructure, specifically, the types of pores present, the area percentage of pores, and average pore size. These insights contribute to a deeper understanding of how casting defects impact the performance of recycled aluminium alloys in sustainable applications, particularly in the context of next-generation electric vehicles.
- Open Access
- 1 December 2024
- Published by Walter de Gruyter GmbH in System Safety: Human - Technical Facility - Environment
- Vol. 6 (1) , 473-484
Various Metallography Techniques for Microstructure Analysis of Ni-Based Superalloys
The Ni-based superalloys are known for the number of phases presented in alloy microstructure. Depending on alloying elements, phases such as austenitic FCC gamma matrix, L 12 gamma prime, DO 22 gamma double prime, BCT delta phase, and MC or M 23 C 6 (or M 6 C) carbides have occurred. With these microstructure components’ variety, the usual optical microscopy analysis is not satisfactory many times. For a better understanding of how single structures affect the lifetime of Ni-based superalloys components (turbine blades or turbine discs) and how they are changing during their operation load is SEM a very powerful tool. Two different types of superalloys were used for experimental evaluation. The first were cast superalloys ZhS6K and IN 738. Both cast superalloys in bar form were subjected to additional heat treatment at 800°C for 10 and 15 hours followed by air-cooling. The influence of gamma prime phase morphology changes on alloy lifetime and Vickers hardness were evaluated by SEM coherent testing grid methods. The second was wrought superalloy IN 718 and Nimonic 80A in bar form to present the various grain size evaluation techniques according to ASTM E112 standards. Various analyses were employed (SEM fractography, BSE observation, EDS mapping, etc.) for microstructure evaluation. The main goal is to show how effective light microscopy and SEM on Ni-based superalloy analysis are when microstructure change evaluation is needed.
- 1 December 2024
- Published by Walter de Gruyter GmbH in System Safety: Human - Technical Facility - Environment
- Vol. 6 (1) , 473-484
Open AccessVarious Metallography Techniques for Microstructure Analysis of Ni-Based Superalloys
The Ni-based superalloys are known for the number of phases presented in alloy microstructure. Depending on alloying elements, phases such as austenitic FCC gamma matrix, L 12 gamma prime, DO 22 gamma double prime, BCT delta phase, and MC or M 23 C 6 (or M 6 C) carbides have occurred. With these microstructure components’ variety, the usual optical microscopy analysis is not satisfactory many times. For a better understanding of how single structures affect the lifetime of Ni-based superalloys components (turbine blades or turbine discs) and how they are changing during their operation load is SEM a very powerful tool. Two different types of superalloys were used for experimental evaluation. The first were cast superalloys ZhS6K and IN 738. Both cast superalloys in bar form were subjected to additional heat treatment at 800°C for 10 and 15 hours followed by air-cooling. The influence of gamma prime phase morphology changes on alloy lifetime and Vickers hardness were evaluated by SEM coherent testing grid methods. The second was wrought superalloy IN 718 and Nimonic 80A in bar form to present the various grain size evaluation techniques according to ASTM E112 standards. Various analyses were employed (SEM fractography, BSE observation, EDS mapping, etc.) for microstructure evaluation. The main goal is to show how effective light microscopy and SEM on Ni-based superalloy analysis are when microstructure change evaluation is needed.
- Open Access
Influence of Copper Addition on the Mechanical Properties and Corrosion Resistance of Self-Hardening Secondary Aluminium Alloy AlZn10Si8Mg
Aluminium alloys have a wide range of applications, mainly due to their advantageous strength-to-weight ratio, denoted as specific strength and corrosion resistance. In recent decades, there has been a notable surge in the usage of recycled alloys, attributed to their reduced production costs and emissions. One of the conditions for secondary production is the optimal sorting of used scrap. Once the aluminium scrap has been melted, it is tough to reduce the content of the various additives. Copper is the primary alloying element in some aluminium alloys, which leads to an increased amount of copper in the aluminium scrap. Therefore, it is important to investigate its effect on the properties of aluminium alloys in which it is not commonly present. For this reason, this paper is concerned with the influence of copper on the microstructure and properties of the secondary aluminium alloy AlZn10Si8Mg. Specifically, it compares two melts of self-hardening AlZn10Si8Mg alloys differing in copper content (0.019% and 1.72%). A complex quantitative and metallographic analysis by optical and electron microscopy has been performed. Mechanical properties were investigated by tensile test, Brinell hardness, and Vickers microhardness measurements. The corrosion resistance of the individual melts was verified by the Audi test.
Open AccessInfluence of Copper Addition on the Mechanical Properties and Corrosion Resistance of Self-Hardening Secondary Aluminium Alloy AlZn10Si8Mg
Aluminium alloys have a wide range of applications, mainly due to their advantageous strength-to-weight ratio, denoted as specific strength and corrosion resistance. In recent decades, there has been a notable surge in the usage of recycled alloys, attributed to their reduced production costs and emissions. One of the conditions for secondary production is the optimal sorting of used scrap. Once the aluminium scrap has been melted, it is tough to reduce the content of the various additives. Copper is the primary alloying element in some aluminium alloys, which leads to an increased amount of copper in the aluminium scrap. Therefore, it is important to investigate its effect on the properties of aluminium alloys in which it is not commonly present. For this reason, this paper is concerned with the influence of copper on the microstructure and properties of the secondary aluminium alloy AlZn10Si8Mg. Specifically, it compares two melts of self-hardening AlZn10Si8Mg alloys differing in copper content (0.019% and 1.72%). A complex quantitative and metallographic analysis by optical and electron microscopy has been performed. Mechanical properties were investigated by tensile test, Brinell hardness, and Vickers microhardness measurements. The corrosion resistance of the individual melts was verified by the Audi test.
- Open Access
- 1 September 2023
- Published by Materials Research Forum, LLC in Materials Research Proceedings
- Vol. 34
Impact of Increased Iron Content and Manganese Addition on Intermetallic Phases and Fatigue Resistance of AlSi7Mg0.6 Secondary Alloy
Impact of Increased Iron Content and Manganese Addition on Intermetallic Phases and Fatigue Resistance of AlSi7Mg0.6 Secondary Alloy MIKOLAJČÍK Martin, TILL
- 1 September 2023
- Published by Materials Research Forum, LLC in Materials Research Proceedings
- Vol. 34
Open AccessImpact of Increased Iron Content and Manganese Addition on Intermetallic Phases and Fatigue Resistance of AlSi7Mg0.6 Secondary Alloy
Impact of Increased Iron Content and Manganese Addition on Intermetallic Phases and Fatigue Resistance of AlSi7Mg0.6 Secondary Alloy MIKOLAJČÍK Martin, TILL
- Open Access
- 11 December 2022
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 22 (5) , 598-604
The Influence of Fe Content on Corrosion Resistance of secondary AlSi7Mg0.3 Cast Alloy with Increased Fe-content
Production of primary aluminium is energetically enormously expensive. The use of secondary (recycled) aluminium, has therefore a high potential to save money and energy while reducing the negative environmental impact of aluminium production. Although the properties of secondary aluminium alloys are generally comparable to those of primary aluminium alloys, the increased Fe content can lead to a significant reduction in the corrosion resistance of these alloys. Secondary (recycled) AlSi7Mg0.3 cast alloy with different iron contents (0.123, 0.454, 0.679 and 1.209 wt. %) in the as-cast and after heat treatment (T6) condition was investigated. The quantitative analysis was focused on the evaluation of the Fe-phases, especially the needle-like Al 5 FeSi phase. The corrosion resistance was measured by a rapid corrosion test (AUDI test). The corrosion damage of the surface was observed macroscopically. The results show that Fe content higher than 0.454 % has no significant effect on the amount and size of needle-like phases of Al 5 FeSi. The corrosion resistance is mainly influenced by the size and length of the Al 5 FeSi phases. Increased Fe content decreases the corrosion resistance of AlSi7Mg0.3 alloy and accelerates the initiation of corrosion.
- 11 December 2022
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 22 (5) , 598-604
Open AccessThe Influence of Fe Content on Corrosion Resistance of secondary AlSi7Mg0.3 Cast Alloy with Increased Fe-content
Production of primary aluminium is energetically enormously expensive. The use of secondary (recycled) aluminium, has therefore a high potential to save money and energy while reducing the negative environmental impact of aluminium production. Although the properties of secondary aluminium alloys are generally comparable to those of primary aluminium alloys, the increased Fe content can lead to a significant reduction in the corrosion resistance of these alloys. Secondary (recycled) AlSi7Mg0.3 cast alloy with different iron contents (0.123, 0.454, 0.679 and 1.209 wt. %) in the as-cast and after heat treatment (T6) condition was investigated. The quantitative analysis was focused on the evaluation of the Fe-phases, especially the needle-like Al 5 FeSi phase. The corrosion resistance was measured by a rapid corrosion test (AUDI test). The corrosion damage of the surface was observed macroscopically. The results show that Fe content higher than 0.454 % has no significant effect on the amount and size of needle-like phases of Al 5 FeSi. The corrosion resistance is mainly influenced by the size and length of the Al 5 FeSi phases. Increased Fe content decreases the corrosion resistance of AlSi7Mg0.3 alloy and accelerates the initiation of corrosion.
- Open Access
- 17 October 2022
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 22 (4) , 436-443
Effect of Higher Iron Content and Manganese Addition on the Corrosion Re-sistance of AlSi7Mg0.6 Secondary Alloy
- 17 October 2022
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 22 (4) , 436-443
Open AccessEffect of Higher Iron Content and Manganese Addition on the Corrosion Re-sistance of AlSi7Mg0.6 Secondary Alloy