Marina Latypova
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Marina Latypova has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Irina E. Volokitina
Karaganda industrial university, Temirtau, Kazakhstan
3 shared publications - Andrey Volokitin
Karaganda industrial university, Temirtau, Kazakhstan
2 shared publications - T. D. Fedorova
Karaganda industrial university, Temirtau, Kazakhstan
2 shared publications - Akmaral Utelbayeva
Department of Science of Production and Innovation, Department of Life Safety and Environmental Protection, M. Auezov South Kazakhstan University, Shymkent 160012, Kazakhstan
1 shared publication - Aktolkyn Agabekova
Department of Electrical engineering, H. A. Yassavi International Kazakh-Turkish University, Turkestan 161200, Kazakhstan
1 shared publication - Alexandr Kolesnikov
Department of Life Safety and Environmental Protection, M. Auezov South Kazakhstan University, Shymkent 160012, Kazakhstan
1 shared publication
Latest Publications
- Open Access
- 30 June 2025
- Published by Karagandy University of the name of academician E.A. Buketov in Eurasian Physical Technical Journal
- Vol. 22 (2 (52)) , 109-120
INVESTIGATION OF THE STRESS-STRAIN STATE DURING NEW COMBINED DEFORMATION TECHNOLOGY
This paper presents the results of finite element modeling of a novel technology of combined deformation by radial-shear broaching and traditional drawing. Using DEFORM program, the parameters of stress-strain state and deformation forces were studied. A range of models with varying initial diameters of the workpiece, single and total compressions, and different temperatures of heating the workpiece were considered. It was revealed that the optimal conditions occurred at 30-25-20 scheme at a temperature of 900°C. However, this scheme can be recommended when the strength of the deforming equipment is sufficient. In other cases, it is necessary to select a scheme that allows for deformation without exceeding the limiting loads.
- 30 June 2025
- Published by Karagandy University of the name of academician E.A. Buketov in Eurasian Physical Technical Journal
- Vol. 22 (2 (52)) , 109-120
Open AccessINVESTIGATION OF THE STRESS-STRAIN STATE DURING NEW COMBINED DEFORMATION TECHNOLOGY
This paper presents the results of finite element modeling of a novel technology of combined deformation by radial-shear broaching and traditional drawing. Using DEFORM program, the parameters of stress-strain state and deformation forces were studied. A range of models with varying initial diameters of the workpiece, single and total compressions, and different temperatures of heating the workpiece were considered. It was revealed that the optimal conditions occurred at 30-25-20 scheme at a temperature of 900°C. However, this scheme can be recommended when the strength of the deforming equipment is sufficient. In other cases, it is necessary to select a scheme that allows for deformation without exceeding the limiting loads.
- 14 August 2024
- Published by Springer Nature in Metallurgist
- Vol. 68 (4) , 530-536
Analysis of the twisting effect in an equal-channel stepped die and drawing on copper wire mechanical properties
- 14 August 2024
- Published by Springer Nature in Metallurgist
- Vol. 68 (4) , 530-536
Analysis of the twisting effect in an equal-channel stepped die and drawing on copper wire mechanical properties
- Open Access
Thermodynamic Simulation of Environmental and Population Protection by Utilization of Technogenic Tailings of Enrichment
During mining, only 4–8% is converted to final products, and the rest is accumulated in landfills. There is a lack of research on the study of various patterns and mechanisms of the formation of cement clinker minerals during the simultaneous distillation of zinc. This paper presents studies of thermodynamic stimulation of environmental and population protection by utilization of technogenic enrichment waste as secondary raw materials for clinker production and zinc extraction. In particular, a comparison of the Gibbs energy (ΔG) of clinker formation under standard chemical equations and under non-standard chemical equations is given. According to the results of the study, using thermodynamic simulation, the temperature intervals of mineral formation, the dependence of the Gibbs energy on temperature (ΔGT°), and the approximation equations were found; it was established that the presence of zinc ferrite contributes to the intensification of the formation of clinker minerals and the extraction of Zn to gas.
Open AccessThermodynamic Simulation of Environmental and Population Protection by Utilization of Technogenic Tailings of Enrichment
During mining, only 4–8% is converted to final products, and the rest is accumulated in landfills. There is a lack of research on the study of various patterns and mechanisms of the formation of cement clinker minerals during the simultaneous distillation of zinc. This paper presents studies of thermodynamic stimulation of environmental and population protection by utilization of technogenic enrichment waste as secondary raw materials for clinker production and zinc extraction. In particular, a comparison of the Gibbs energy (ΔG) of clinker formation under standard chemical equations and under non-standard chemical equations is given. According to the results of the study, using thermodynamic simulation, the temperature intervals of mineral formation, the dependence of the Gibbs energy on temperature (ΔGT°), and the approximation equations were found; it was established that the presence of zinc ferrite contributes to the intensification of the formation of clinker minerals and the extraction of Zn to gas.